ORiNOCO PC Card supported in -stable or -current?
Alexander Leidinger <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.mobile |
|---|---|
| Message-ID | <[email protected]> |
Hi,
please keep me in the CC, thanks.
I've got an OEM version of an "ORiNOCO PC Card" for my desktop system.
At least the linux driver tells me it is an "ORiNOCO PC Card" in it's
man page and in the source (and it refers to
http://www.orinocowireless.com).
I've attached the "pccardc dumpcis" output.
Is this card supported (either in -stable or in -current) and what do I
have to do to have it set up by pccardd upon insertion into the PCMCIA
bridge?
Bye,
Alexander.
--
The dark ages were caused by the Y1K problem.
http://www.Leidinger.net Alexander @ Leidinger.net
GPG fingerprint = C518 BC70 E67F 143F BE91 3365 79E2 9C60 B006 3FE7
pccard.txt
(text/plain, 2.5 KB)
Configuration data for card in slot 0
Tuple #1, code = 0x1 (Common memory descriptor), length = 3
000: 00 00 ff
Common memory device information:
Device number 1, type No device, WPS = OFF
Speed = No speed, Memory block size = 512b, 1 units
Tuple #2, code = 0x17 (Attribute memory descriptor), length = 4
000: 67 5a 08 ff
Attribute memory device information:
Device number 1, type SRAM, WPS = OFF
Speed = 5.0 x 100 ns, Memory block size = 512b, 2 units
Tuple #3, code = 0x1d (Other conditions for attribute memory), length = 5
000: 01 67 5a 08 ff
(MWAIT)
Tuple #4, code = 0x1c (Other conditions for common memory), length = 4
000: 01 00 00 ff
(MWAIT)
Tuple #5, code = 0x15 (Version 1 info), length = 39
000: 05 00 20 00 49 45 45 45 20 38 30 32 2e 31 31 20
010: 57 69 72 65 6c 65 73 73 20 4c 41 4e 2f 50 43 20
020: 43 61 72 64 00 00 ff
Version = 5.0, Manuf = [ ], card vers = [IEEE 802.11 Wireless LAN/PC Card]
Addit. info = []
Tuple #6, code = 0x20 (Manufacturer ID), length = 4
000: 01 d6 02 00
PCMCIA ID = 0xd601, OEM ID = 0x2
Tuple #7, code = 0x21 (Functional ID), length = 2
000: 06 00
Network/LAN adapter
Tuple #8, code = 0x22 (Functional EXT), length = 2
000: 01 07
Network technology: Wireless
Tuple #9, code = 0x22 (Functional EXT), length = 5
000: 02 40 42 0f 00
Network speed: 1 Mb/sec
Tuple #10, code = 0x22 (Functional EXT), length = 5
000: 02 80 84 1e 00
Network speed: 2 Mb/sec
Tuple #11, code = 0x22 (Functional EXT), length = 2
000: 03 07
Network media: 2.4 GHz
Tuple #12, code = 0x22 (Functional EXT), length = 2
000: 05 01
Network connector: closed connector standard
Tuple #13, code = 0x1a (Configuration map), length = 7
000: 03 02 e0 03 00 00 01
Reg len = 4, config register addr = 0x3e0, last config = 0x2
Registers: X-------
Tuple #14, code = 0x1b (Configuration entry), length = 16
000: c1 01 19 77 55 c5 4b d5 19 36 36 05 46 7f ff ff
Config index = 0x1(default)
Interface byte = 0x1 (I/O)
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Minimum operating supply voltage: 4 x 1V, ext = 0x4b
Maximum operating supply voltage: 5 x 1V, ext = 0x19
Max current average over 1 second: 3 x 100mA
Max current average over 10 ms: 3 x 100mA
Power down supply current: 1 x 10mA
Card decodes 6 address lines, limited 8/16 Bit I/O
IRQ modes: Level, Pulse
IRQs: NMI IOCK BERR VEND 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Tuple #15, code = 0xff (Terminator), length = 0
1 slots found