PCMCIA ATA flash card problem

Hi!

I have just aquired a Kingston Technology 48Mb PCMCIA ATA flash storage
card, and was hoping to use it on my NEWCARD FreeBSD-CURRENT system.
However, inserting the card yields the following output:

pccard1: Allocation failed for cfe 0
ata2 at port 0x110-0x11f irq 11 function 0 config 1 on pccard1
pccard1: WARNING: Resource not reserved by pccard bus
device_probe_and_attach: ata2 attach returned 6

I have searched the mailing list archives and the web, and very few other
people hae had a problem with ATA PCMCIA cards. However with full pccard
debugging enabled, here's what I get (notice the bad-sounding "not yet
implemented" messages):

pccard1: chip_socket_enable
pccard1: read_cis
cis mem map c9736000
pccard1: CIS tuple chain:
CISTPL_DEVICE type=funcspec speed=250ns
 01 03 d9 01 ff
unhandled CISTPL 18
 18 02 df 01
CISTPL_FUNCID
 21 02 04 01
CISTPL_FUNCE
 22 02 01 01
CISTPL_FUNCE
 22 03 02 04 07
CISTPL_CONFIG
 1a 06 05 03 00 02 7f 02
CISTPL_CFTABLE_ENTRY
 1b 06 c0 c0 a0 08 00 20
CISTPL_CFTABLE_ENTRY
 1b 08 c1 41 98 64 f0 ff ff 20
CISTPL_CFTABLE_ENTRY
 1b 0c 82 41 18 ea 61 f0 01 07 f6 03 01 ee
CISTPL_CFTABLE_ENTRY
 1b 0c 83 41 18 ea 61 70 01 07 76 03 01 ee
CISTPL_VERS_1
 15 11 05 00 4b 54 43 20 20 00 41 54 41 00 31 2e
 30 00 ff
unhandled CISTPL 80
 80 04 2d 48 50 2d
CISTPL_NO_LINK
 14 00
CISTPL_END
 ff
pccard1: check_cis_quirks
pccard1: CIS version PC Card Standard 5.0
pccard1: CIS info: KTC  , ATA, 1.0
pccard1: Manufacturer code 0xffffffff, product 0xffffffff
pccard1: function 0: fixed disk, ccr addr 200 mask 27f
pccard1: function 0, config table entry 0: memory card; irq mask 0; memspace 0-7ff; powerdown
pccard1: function 0, config table entry 1: I/O card; irq mask ffff; iomask 4, iospace 0-f; memspace 0-7ff; powerdown
pccard1: function 0, config table entry 2: I/O card; irq mask 4000; iomask a, iospace 1f0-1f7 3f6-3f7; memspace 0-7ff; rdybsy_active io8 io16 irqshare irqpulse irqlevel powerdown
pccard1: function 0, config table entry 3: I/O card; irq mask 4000; iomask a, iospace 170-177 376-377; memspace 0-7ff; rdybsy_active io8 io16 irqshare irqpulse irqlevel powerdown
pccard1: functions scanning
pccard1: Memory space not yet implemented.
pccard1: Neither memory nor I/O mampped
pccard1: Allocation failed for cfe 0
pccard1: I/O rid 0 start 0 end ffffffff
pccard1: Memory space not yet implemented.
pccard1: ccr_res == 84003000-840033ff, base=200
pccard1: function 0 CCR at 0 offset 200: 41 a0 2e 0, 0 0 0 0, 0
ata2 at port 0x110-0x11f irq 11 function 0 config 1 on pccard1
pccard1: WARNING: Resource not reserved by pccard bus
ata2: probe allocation failed
device_probe_and_attach: ata2 attach returned 6

Any suggestions? Where can I go from here?

With thanks,

Gavin


To Unsubscribe: send mail to [email protected]
with "unsubscribe freebsd-mobile" in the body of the message