wierd(to me) messages from setup of (supported) modem card.

I noticed the errors at the top of this pccardc dumpcis also at pccardd 
startup
at boot:

Code 128 not found
Code 128 not found
code Unknown ignored
Code 131 not found
Code 131 not found
code Unknown ignored
Configuration data for card in slot 0
Tuple #1, code = 0x1 (Common memory descriptor), length = 3
    000:  00 00 ff
	Common memory device information:
		Device number 1, type No device, WPS = OFF
		Speed = No speed, Memory block size = 512b, 1 units
Tuple #2, code = 0x15 (Version 1 info), length = 57
    000:  04 01 54 6f 73 68 69 62 61 20 41 6d 65 72 69 63
    010:  61 00 33 43 58 4d 30 35 36 2d 42 4e 57 00 33 43
    020:  4f 4d 2f 4e 6f 74 65 57 6f 72 74 68 79 20 35 36
    030:  4b 20 4d 6f 64 65 6d 00 ff
	Version = 4.1, Manuf = [Toshiba America], card vers = [3CXM056-BNW]
	Addit. info = [3COM/NoteWorthy 56K Modem]
Tuple #3, code = 0x20 (Manufacturer ID), length = 4
    000:  01 01 2f 00
	PCMCIA ID = 0x101, OEM ID = 0x2f
Tuple #4, code = 0x21 (Functional ID), length = 2
    000:  02 01
	Serial port/modem - POST initialize
Tuple #5, code = 0x1a (Configuration map), length = 5
    000:  01 23 00 03 03
	Reg len = 2, config register addr = 0x300, last config = 0x23
	Registers: XX------
Tuple #6, code = 0x1b (Configuration entry), length = 16
    000:  e0 41 99 49 55 3e 3d aa 60 f8 03 07 30 ff ff 28
	Config index = 0x20(default)
	Interface byte = 0x41 (I/O)  +RDY/-BSY active
	Vcc pwr:
		Nominal operating supply voltage: 5 x 1V
		Continuous supply current: 3.5 x 100mA
		Power down supply current: 3.5 x 10mA
	Card decodes 10 address lines, 8 Bit I/O only
		I/O address # 1: block start = 0x3f8 block length = 0x8
		IRQ modes: Level
		IRQs:  0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
	Max twin cards = 0
	Misc attr: (Audio-BVD2) (Power down supported)
Tuple #7, code = 0x1b (Configuration entry), length = 7
    000:  21 08 aa 60 f8 02 07
	Config index = 0x21
	Card decodes 10 address lines, 8 Bit I/O only
		I/O address # 1: block start = 0x2f8 block length = 0x8
Tuple #8, code = 0x1b (Configuration entry), length = 7
    000:  22 08 aa 60 e8 03 07
	Config index = 0x22
	Card decodes 10 address lines, 8 Bit I/O only
		I/O address # 1: block start = 0x3e8 block length = 0x8
Tuple #9, code = 0x1b (Configuration entry), length = 7
    000:  23 08 aa 60 e8 02 07
	Config index = 0x23
	Card decodes 10 address lines, 8 Bit I/O only
		I/O address # 1: block start = 0x2e8 block length = 0x8
Tuple #10, code = 0x22 (Functional EXT), length = 4
    000:  00 02 0f 7c
	Serial interface extension:
		16550 UART, Parity - Space,Mark,Odd,Even
		Data bit - 7bit,8bit, Stop bit - 1bit,1.5bit,2bit
Tuple #11, code = 0x22 (Functional EXT), length = 9
    000:  01 1f 0f 00 06 00 00 06 00
	Modem interface capabilities:
Tuple #12, code = 0x22 (Functional EXT), length = 12
    000:  02 06 00 3f 1c 03 03 0f 07 00 02 b5
	Data modem services available:
Tuple #13, code = 0x22 (Functional EXT), length = 8
    000:  13 06 00 0f 00 02 00 b5
	Fax1/modem services available:
Tuple #14, code = 0x22 (Functional EXT), length = 8
    000:  23 06 00 0f 00 02 00 b5
	Fax2/modem services available:
Tuple #15, code = 0x0 (Null tuple), length = 10
    000:  02 01 2f 00 21 00 07 00 00 ff
Tuple #16, code = 0x0 (Null tuple), length = 14
    000:  31 30 39 4e 31 38 39 38 32 30 48 39 00 ff
Tuple #17, code = 0x14 (No link), length = 0
Tuple #18, code = 0xff (Terminator), length = 0
2 slots found

I'm wondering if those code not found and code unknown ignored messages
are a problem, or just me having a weird setup?

I can supply a dmesg if that would help any.


-- 
Larry Rosenman                     http://www.lerctr.org/~ler
Phone: +1 972-414-9812                 E-Mail: [email protected]
US Mail: 1905 Steamboat Springs Drive, Garland, TX 75044-6749




To Unsubscribe: send mail to [email protected]
with "unsubscribe freebsd-mobile" in the body of the message