Re: CD/CD-RW drive not working on Dell Inspiron 7500

On Sun, Apr 21, 2002 at 05:10:08PM +0200, Paul Schenkeveld wrote:


Imation CDR media suck big time. I've seen Yamaha SCSI writers barf on
them, and even (occasionally) my Plextor as well.

W/

> I was able to write to a Sony CD-RW certified for 1x, 2x and 4x
> speed.  Writing to an Imation 4x-10x speed CD-RW doesn't work at
> any speed however (although Dell specifies the drive as 8x speed).
> I also tried using the Dell supplied software under XP (sorry, I
> hate that but I just wanted to be sure) with the same results.
> 
> I also wasn't able to write audio to any media.  Burncd always
> replies:
> 
>     $ burncd -s 1 audio track001.raw
>     writing from file track001.raw size 36111 KB
> 
>     only wrote -1 of 37632 bytes
> 
> and the console barks at me:
> 
>     acd0: WRITE_BIG - ILLEGAL REQUEST asc=64 ascq=00 error=00
> 
> My kernel is a RELENG_4_5 (pl 3) because a RELENG_4 kernel cannot
> access my CD-RW drive at all (get a device not configured error
> although acd0 appears in dmesg).
> 
> So far I can live with this situation as burning audio is not
> really important to me and I think I'll just throw away the
> Imation media and get some more Sony 1x-4x media to work with.
> 
> Regards,
> 
> Paul Schenkeveld
> 
> On Thu, Apr 18, 2002 at 01:50:21PM +0200, Paul Schenkeveld wrote:
> > Hi Nick, FreeBSD community,
> > 
> > I just got a Dell Inspiron showing the same error messages under
> > FreeBSD 4.5 pl3.  Since I saw no followup with a solution I was
> > wondering whether you got the CD/RW to work (ie. to write writable
> > and rewritable media).
> > 
> > I can mount and read CDs and a CDRW written on a Yamaha SCSI burner
> > but 'burncd msinfo' and 'burncd blank' already give errors.  From
> > my kernel config:
> > 
> > device		ata0	at isa? port IO_WD1 irq 14
> > device		ata1	at isa? port IO_WD2 irq 15
> > device		ata
> > device		atadisk			# ATA disk drives
> > device		atapicd			# ATAPI CDROM drives
> > #evice		atapifd			# ATAPI floppy drives
> > #evice		atapist			# ATAPI tape drives
> > 
> > >From /var/log/messages:
> > 
> > Apr 18 11:35:41 i4100 /kernel: acd0: CD-RW <HL-DT-ST CD-RW GCE-8080N> at ata1-master using PIO4
> > Apr 18 13:30:37 i4100 /kernel: acd0: READ_BIG - MEDIUM ERROR asc=02 ascq=00 error=00
> > Apr 18 13:31:34 i4100 /kernel: acd0: READ_TRACK_INFO - ILLEGAL REQUEST asc=24 ascq=00 error=00
> > Apr 18 13:31:44 i4100 /kernel: acd0: READ_TRACK_INFO - ILLEGAL REQUEST asc=24 ascq=00 error=00
> > Apr 18 13:33:43 i4100 /kernel: acd0: BLANK_CMD - ILLEGAL REQUEST asc=64 ascq=00 error=00
> > 
> > Bye,
> > 
> > Paul Schenkeveld
> > 
> > On Wed, Oct 17, 2001 at 03:17:22PM -0700, Nick Tonkin wrote:
> > > 
> > > Hello FreeBSD folks,
> > > 
> > > I cannot get the CD-CD/RW drive to work under FreeBSD 4.4 on my Dell
> > > inspiron  7500. I know this has been brought up before but I could not
> > > find a solution.
> > > 
> > > The CD drive is made by Matsushita I think, product number is UJDA310L
> > > 
> > > Note that the behavior is different depending on whether or not there
> > > is a disk in tghe drive at boot. When I start the machine with a disk in
> > > it I get this:
> > > 
> > >  root@bomba ~>dmesg | grep -n acd0
> > > 78:acd0: CDROM <UJDA310 Program Loader> at ata1-master using PIO2
> > > 86:acd0: PREVENT_ALLOW - ILLEGAL REQUEST asc=20 ascq=00 error=00
> > > 87:acd0: PREVENT_ALLOW - ILLEGAL REQUEST asc=20 ascq=00 error=00
> > > 88:acd0: PREVENT_ALLOW - ILLEGAL REQUEST asc=20 ascq=00 error=00
> > > 89:acd0: READ_BIG - ILLEGAL REQUEST asc=20 ascq=00 error=00
> > > 90:acd0: PREVENT_ALLOW - ILLEGAL REQUEST asc=20 ascq=00 error=00
> > > 
> > > ... and then:
> > > 
> > > root@bomba ~>mount /cdrom
> > > cd9660: /dev/acd0c: Input/output error
> > > 
> > > ... whereas if I start the machine without a disk in it, I get:
> > > 
> > > root@bomba ~>grep -n acd0 ~nick/foo
> > > 78:acd0: CD-RW <UJDA310> at ata1-master using PIO4
> > > 167:acd0: CD-RW <UJDA310> a4 ata1-master using PIO4
> > > 256:acd0: CD-RW <UJDA310> at ata1-master using PIO4
> > > 351:acd0: CD-RW <UJDA310> at ata1-master using PIO4
> > > 358:acd0: PREVENT_ALLOW - ILLEGAL REQUEST asc=20 ascq=00 error=00
> > > 359:acd0: PREVENT_ALLOW - ILLEGAL REQUEST asc=20 ascq=00 error=00
> > > 360:acd0: READ_BIG - ILLEGAL REQUEST asc=20 ascq=00 error=00
> > > 361:acd0: PREVENT_ALLOW - ILLEGAL REQUEST asc=20 ascq=00 error=00
> > > 
> > > ... and then I can open the drive OK, insert a disk, close the drive
> > > manually (the drawer is not drawn in by the motor as with other CD-ROM
> > > drives I have used, or as with this one under windoze), and then I get:
> > > 
> > > root@bomba ~>mount /cdrom
> > > cd9660: /dev/acd0c: Input/output error
> > >  ... followed by the same series of errors.
> > > 
> > > Any help greatly appreciated.
> > > 
> > > root@bomba ~>uname -a
> > > FreeBSD bomba.rlnt.net 4.4-RELEASE FreeBSD 4.4-RELEASE #0: Wed Oct 17
> > > 12:59:32
> > >  PDT 2001     [email protected]:/usr/src/sys/compile/WITHSOUND  i386
> > > 
> > > 
> > > ~~~~~~~~~~~
> > > Nick Tonkin
> > > 
> > > 
> > > To Unsubscribe: send mail to [email protected]
> > > with "unsubscribe freebsd-mobile" in the body of the message
> > 
> > To Unsubscribe: send mail to [email protected]
> > with "unsubscribe freebsd-mobile" in the body of the message
> 
> To Unsubscribe: send mail to [email protected]
> with "unsubscribe freebsd-mobile" in the body of the message
---end of quoted text---

-- 
|   / o / /_  _   				[email protected]
|/|/ / / /(  (_)  Bulte				Arnhem, the Netherlands

To Unsubscribe: send mail to [email protected]
with "unsubscribe freebsd-mobile" in the body of the message