ACPI and IRQ problems

I have Acer TM 620 notebook with onboard fxp NIC that failed to work on
FreeBSD.
When I bring fxp up all userland is frozen and I got "fxp0: device
timeout" message repeating.

Seems that most devices are using IRQ 10 and I suspect ACPI. Disabling
ACPI doesn't help so I tried also to correct ACPI DSDT but without
success.

I would appreciate any help with this problem.

Thanks,

Damjan


Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights
reserved.
FreeBSD 5.0-CURRENT #1: Mon May  5 09:22:35 CEST 2003
    root@:/usr/src/sys/i386/compile/DAMJAN-OLD
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0505000.
Preloaded acpi_dsdt "/boot/acpi_dsdt.aml" at 0xc05050a8.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc05050f0.
Timecounter "i8254"  frequency 1193182 Hz Timecounter "TSC"  frequency
999891727 Hz
CPU: Intel(R) Pentium(R) III Mobile CPU      1000MHz (999.89-MHz
686-class CPU)
  Origin = "GenuineIntel"  Id = 0x6b1  Stepping = 1
 
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,C
MOV,PAT,PSE36,MMX,FXSR,SSE>
real memory  = 528285696 (503 MB)
avail memory = 507650048 (484 MB)
Pentium Pro MTRR support enabled
ACPI: DSDT was overridden.
    ACPI-0375: *** Info: Table [DSDT] replaced by host OS
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <Acer   TM530   > on motherboard
pcibios: BIOS version 2.10
Using $PIR table, 7 entries at 0xc00fb700
acpi_bus_number: root bus has no _BBN, assuming 0
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI-fast"  frequency 3579545 Hz
acpi_bus_number: root bus has no _BBN, assuming 0
acpi_timer0: <24-bit timer at 3.579545MHz> port 0xf108-0xf10b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> on acpi0
acpi_tz1: <thermal zone> on acpi0
acpi_button0: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82830M (830M GMCH) SVGA controller> mem
0x90100000-0x9017ffff,0x98000000-0x9fffffff irq 11 at device 2.0 on pci0
agp0: detected 8060k stolen memory
agp0: aperture size is 128M
pci0: <display> at device 2.1 (no driver attached)
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port
0xa4a0-0xa4bf irq 11 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port
0xa4e0-0xa4ff irq 10 at device 29.1 on pci0
usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> port
0xa800-0xa81f irq 11 at device 29.2 on pci0
usb2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci1: <ACPI PCI bus> on pcib1
fwohci0: vendor=104c, dev=8026
fwohci0: <1394 Open Host Controller Interface> mem
0x80104000-0x80107fff,0x80100000-0x801007ff irq 10 at device 3.0 on pci1
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channel is 4.
fwohci0: EUI64 10:25:10:1f:00:02:f7:2f
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
sbp0: <SBP2/SCSI over firewire> on firewire0
fwohci0: Initiate bus reset
pci1: <network, ethernet> at device 8.0 (no driver attached)
pcic0: <O2micro 6933 PCI-Cardbus Bridge> irq 10 at device 9.0 on pci1
pcic0: Could not grab register memory
device_probe_and_attach: pcic0 attach returned 12
pcic0: <O2micro 6933 PCI-Cardbus Bridge> irq 10 at device 9.1 on pci1
pcic0: Could not grab register memory
device_probe_and_attach: pcic0 attach returned 12
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 UDMA100 controller> port
0xa890-0xa89f,0xa878-0xa87b,0xa860-0xa867,0xa848-0xa84b,0xa830-0xa837 at
device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pci0: <multimedia, audio> at device 31.5 (no driver attached)
pci0: <simple comms> at device 31.6 (no driver attached)
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_acad0: <AC adapter> on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 8250 or not responding
sio1 port 0x240-0x247,0x2f8-0x2ff irq 3 drq 3 on acpi0
sio1: type 16550A
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
pmtimer0 on isa0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
pcic0: <Intel i82365SL-DF> at port 0x3e0 iomem 0xd0000 on isa0
pcic0: Polling mode
pccard0: <PC Card 16-bit bus (classic)> on pcic0
pccard1: <PC Card 16-bit bus (classic)> on pcic0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0 Timecounters tick every 10.000 msec
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
acpi_acad0: acline initialization start
acpi_acad0: On Line
acpi_acad0: acline initialization done, tried 1 times
acpi_cmbat0: battery initialization start
acpi_cmbat0: battery initialization done, tried 1 times
ad0: 19077MB <TOSHIBA MK2018GAP> [38760/16/63] at ata0-master UDMA100
acd0: DVD-ROM <TOSHIBA DVD-ROM SD-C2502> at ata1-master PIO4
pccard: card inserted, slot 1
Mounting root from ufs:/dev/ad0s3a
pccard: card inserted, slot 0
wi0 at port 0x240-0x27f irq 5 slot 0 on pccard0
wi0: 802.11 address: 00:02:2d:0b:01:b8
wi0: using Lucent Technologies, WaveLAN/IEEE
wi0: Lucent Firmware: Station (6.16.1)
wi0: supported rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
module_register: module pccard/wi already exists!
Module pccard/wi failed to register: 17
module_register: module pci/wi already exists!
Module pci/wi failed to register: 17
pcic2: <O2micro 6933 PCI-Cardbus Bridge> irq 10 at device 9.0 on pci1
pcic2: Could not map register memory 0xfffff000
device_probe_and_attach: pcic2 attach returned 12
pcic2: <O2micro 6933 PCI-Cardbus Bridge> irq 10 at device 9.1 on pci1
pcic2: Could not map register memory 0xfffff000
device_probe_and_attach: pcic2 attach returned 12 stray irq 7
fxp0: <Intel 82801CAM (ICH3) Pro/100 VE Ethernet> port 0x7000-0x703f mem
0x80101000-0x80101fff irq 10 at device 8.0 on pci1
device_probe_and_attach: fxp0 attach returned 12
pcic2: <O2micro 6933 PCI-Cardbus Bridge> irq 10 at device 9.0 on pci1
pcic2: Could not map register memory 0xfffff000
device_probe_and_attach: pcic2 attach returned 12
pcic2: <O2micro 6933 PCI-Cardbus Bridge> irq 10 at device 9.1 on pci1
pcic2: Could not map register memory 0xfffff000
device_probe_and_attach: pcic2 attach returned 12
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"