wi, hostap and WEP strangeness

Hi all,

I'm having some trouble getting hostap and WEP to play nicely together -
some cards work while some others don't.

One machine is a 4.8R box with a SMC2602W PCI wireless adapter, configured
in hostap mode with a 128-bit WEP key:

FreeBSD 4.8-RELEASE #0: Thu Apr  3 10:53:38 GMT 2003
    [email protected]:/usr/obj/usr/src/sys/GENERIC
[...]
wi0: <PRISM2STA WaveLAN> port 0xe400-0xe43f,0xe000-0xe07f mem 0xde003000-0xde003fff irq 10 at device 20.0 on pci0
wi0: 802.11 address: 00:04:e2:0e:36:b0
wi0: using RF:PRISM2 MAC:HFA3841 CARD:HWB3163 rev.A
wi0: Intersil Firmware: Primary 0.03.00, Station 0.08.03

The other machine is a laptop running 5.0-CURRENT from a while ago.  It's
running a slimmed-down OLDCARD kernel (old machine with no NEWCARD support
yet):

FreeBSD 5.0-CURRENT #3: Wed Apr  9 00:07:38 BST 2003
    scott@tuatara:/local/0/obj/local/0/-CURRENT/src/sys/ORAC

Card #1 is a Dell Truemobile, which appears to be a rebadged Lucent/Orinoco
Gold card.  It works perfectly with the hostap box, with and without WEP
enabled:

wi0 at port 0x240-0x27f irq 3 slot 0 on pccard0
wi0: 802.11 address: 00:02:2d:50:ee:ff
wi0: using Lucent Technologies, WaveLAN/IEEE
wi0: Lucent Firmware: Station (8.10.1)
wi0: supported rates: 1Mbps 2Mbps 5.5Mbps 11Mbps

Card #2 is an Intel 2011, which works with WEP turned off but refuses to
associate with the AP when I turn WEP on:

wi0 at port 0x280-0x2c7 iomem 0xd4000-0xd43ff irq 3 slot 0 on pccard0
wi0: 802.11 address: 00:02:b3:04:a1:c5
wi0: using RF:PRISM2 MAC:HFA3841
wi0: Symbol Firmware: Primary (2.1.2), Station (2.20.2)
wi0: supported rates: 1Mbps 2Mbps 5.5Mbps 11Mbps

I'm using the same /etc/start_if.wi0 script to set up the card in both
cases, so I doubt it's a configuration error.  The Intel card works with a
standalone AP, WEP enabled, at the office, in a Windows laptop.

I've seen this problem mentioned on the lists before, but it's generally
been written off to 'flaky Windows drivers', eg. kern/41834.  That's pretty
clearly not the case here... I guess it could be a firmware issue, but I
thought I should ask here before I start trawling around for firmware and
moving cards into Windows boxes to flash them.

So, any ideas?  This is just a toy network, so I'm happy to try almost
anything, especially on the -CURRENT box.  And yes, I know WEP is rubbish,
but it does at least put up the wireless equivalent of a 'keep out' sign
until I find the time to sort out something better,

Cheers,

	Scott

-- 
===========================================================================
Scott Mitchell           | PGP Key ID | "Eagles may soar, but weasels
Cambridge, England       | 0x54B171B9 |  don't get sucked into jet engines"
scott at fishballoon.org | 0xAA775B8B |      -- Anon
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"