ed1: remote transmit DMA failed to complete

Hi,

since I upgraded my laptop from 5-CURRENT April 2003 to 5-CURRENT Jun 19, 
I get 

Jun 25 22:30:26 blob kernel: ed: packets buffered, but transmitter idle
Jun 25 22:30:26 blob kernel: ed1: remote transmit DMA failed to complete
Jun 25 22:30:49 blob last message repeated 5 times
Jun 25 22:32:39 blob last message repeated 10 times

messages over and over. Network still works though. Any ideas?

Thanks,
Johannes

pciconf -lv:

hostb0@pci0:0:0:	class=0x060000 card=0x01ab1014 chip=0x71948086 rev=0x01 hdr=0x00
    vendor   = 'Intel Corporation'
    device   = '82440MX CPU to I/O Controller'
    class    = bridge
    subclass = HOST-PCI
pcm0@pci0:0:1:	class=0x040100 card=0x01a11014 chip=0x71958086 rev=0x00 hdr=0x00
    vendor   = 'Intel Corporation'
    device   = '82443MX? AC97 Audio Controller'
    class    = multimedia
    subclass = audio
none0@pci0:0:2:	class=0x070300 card=0x01a21014 chip=0x71968086 rev=0x00 hdr=0x00
    vendor   = 'Intel Corporation'
    device   = '82440 - 443MX AC97 Modem Controller (Winmodem)'
    class    = simple comms
none1@pci0:2:0:	class=0x030000 card=0x01a41014 chip=0x0712126f rev=0xa0 hdr=0x00
    vendor   = 'Silicon Motion Inc'
    device   = 'SM712 LynxEM+'
    class    = display
    subclass = VGA
cbb0@pci0:3:0:	class=0x060700 card=0x01a31014 chip=0x68721217 rev=0x05 hdr=0x02
    vendor   = 'O2 Micro Inc'
    device   = 'OZ6812 CardBus Controller'
    class    = bridge
    subclass = PCI-CardBus
isab0@pci0:7:0:	class=0x060100 card=0x00000000 chip=0x71988086 rev=0x01 hdr=0x00
    vendor   = 'Intel Corporation'
    device   = '82443MX PCI to ISA Bridge'
    class    = bridge
    subclass = PCI-ISA
atapci0@pci0:7:1:	class=0x010180 card=0x00000000 chip=0x71998086 rev=0x00 hdr=0x00
    vendor   = 'Intel Corporation'
    device   = '82443MX EIDE Controller'
    class    = mass storage
    subclass = ATA
uhci0@pci0:7:2:	class=0x0c0300 card=0x00000000 chip=0x719a8086 rev=0x00 hdr=0x00
    vendor   = 'Intel Corporation'
    device   = '82443MX USB Universal Host Controller'
    class    = serial bus
    subclass = USB
none2@pci0:7:3:	class=0x068000 card=0x00000000 chip=0x719b8086 rev=0x00 hdr=0x00
    vendor   = 'Intel Corporation'
    device   = '82443MX Power Management Controller'
    class    = bridge
    subclass = PCI-unknown




dmesg:

Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.1-CURRENT #2: Wed Jun 25 22:39:24 CEST 2003
    [email protected]:/usr/src/sys/i386/compile/ISERIES
Preloaded elf kernel "/boot/kernel/kernel" at 0xc05bf000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc05bf21c.
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 548866152 Hz
CPU: Intel Celeron (548.87-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x683  Stepping = 3
  Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory  = 201195520 (191 MB)
avail memory = 189165568 (180 MB)
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <IBM    ATLANTA > on motherboard
pcibios: BIOS version 2.10
Using $PIR table, 5 entries at 0xc00fbdb0
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI-fast"  frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0xf008-0xf00b on acpi0
acpi_cpu0: <CPU> port 0x530-0x537 on acpi0
acpi_tz0: <thermal zone> port 0x530-0x537 on acpi0
acpi_button0: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib0: slot 0 INTB is routed to irq 11
pcib0: slot 0 INTB is routed to irq 11
pcib0: slot 2 INTA is routed to irq 10
pcib0: slot 3 INTA is routed to irq 10
pcib0: slot 7 INTD is routed to irq 10
pcm0: <Intel 443MX> port 0x7400-0x743f,0x7000-0x70ff irq 11 at device 0.1 on pci0
pcm0: <Cirrus Logic CS4299 AC97 Codec>
pci0: <simple comms> at device 0.2 (no driver attached)
pci0: <display, VGA> at device 2.0 (no driver attached)
cbb0: <O2Micro OZ6812/6872 PCI-CardBus Bridge> irq 10 at device 3.0 on pci0
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port 0x8040-0x804f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82443MX USB controller> port 0x8000-0x801f irq 10 at device 7.2 on pci0
usb0: <Intel 82443MX USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_acad0: <AC adapter> on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
ppc0 port 0x7bc-0x7bf,0x3bc-0x3c3 irq 7 drq 1 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/7 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0
orm0: <Option ROM> at iomem 0xc0000-0xcbfff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
ed1: <ACCTON EN2216-PCMCIA-ETHERNET> at port 0x300-0x31f irq 10 function 0 config 32 on pccard0
ed1: address 00:00:e8:19:ce:f5, type NE2000 (16 bit) 
ad0: 19077MB <FUJITSU MHR2020AT> [38760/16/63] at ata0-master UDMA33
acd0: CDROM <CD-224E> at ata0-slave PIO4
Mounting root from ufs:/dev/ad0s3a
ed1: remote transmit DMA failed to complete
<snip>
ed: packets buffered, but transmitter idle
<snip>
ed1: remote transmit DMA failed to complete
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"