Re: cardbus network problem with -current

"Kenneth D. Merry" <[email protected]>
Newsgroups gmane.os.freebsd.devel.mobile
Message-ID <[email protected]> 
On Tue, Jul 01, 2003 at 17:32:18 -0600, M. Warner Losh wrote:
> Can you turn on the following debugging and try again?  Also, please
> post questions relating to cardbus/pccard to mobile@ since I read that
> more often than I read current@.  Thanks much.
> 
> hw.cardbus.debug: 1
> hw.cardbus.cis_debug: 1
> hw.cbb.debug: 1

Okay, here is dmesg output with those variables set.

All I did was boot with the card inserted in the slot, and then after the
machine booted, I pulled it out and re-inserted it.

Thanks!

Ken
-- 
Kenneth Merry
[email protected]

_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"
erebor.dmesg.20030701 (text/plain, 8.5 KB) 
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.1-CURRENT #0: Mon Jun 30 21:32:23 MDT 2003
    [email protected]:/usr/home/ken/perforce2/FreeBSD-ken/src/sys/i386/compile/erebor
Preloaded elf kernel "/boot/kernel/kernel" at 0xc067e000.
Preloaded acpi_dsdt "/boot/acpi_dsdt.aml" at 0xc067e1cc.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc067e214.
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 2492656604 Hz
CPU: Mobile Intel(R) Pentium(R) 4 - M CPU 2.50GHz (2492.66-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf27  Stepping = 7
  Features=0xbfebf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
real memory  = 536535040 (511 MB)
avail memory = 514105344 (490 MB)
Pentium Pro MTRR support enabled
ACPI: DSDT was overridden.
    ACPI-0375: *** Info: Table [DSDT] replaced by host OS
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <DELL   CPi R  > on motherboard
pcibios: BIOS version 2.10
Using $PIR table, 9 entries at 0xc00fc590
Timecounter "ACPI-fast"  frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_cpu0: <CPU> port 0x530-0x537 on acpi0
acpi_tz0: <thermal zone> on acpi0
acpi_acad0: <AC adapter> on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_cmbat1: <Control method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib0: slot 29 INTA is routed to irq 11
pcib0: slot 29 INTB is routed to irq 11
pcib0: slot 29 INTC is routed to irq 11
pcib0: slot 29 INTD is routed to irq 11
pcib0: slot 31 INTB is routed to irq 11
pcib0: slot 31 INTB is routed to irq 11
agp0: <Intel 82845 host to AGP bridge> mem 0xec000000-0xefffffff at device 0.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib1: slot 0 INTA is routed to irq 11
pci1: <display, VGA> at device 0.0 (no driver attached)
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xbf80-0xbf9f irq 11 at device 29.0 on pci0
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xbf40-0xbf5f irq 11 at device 29.1 on pci0
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xbf20-0xbf3f irq 11 at device 29.2 on pci0
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3: vendor 0x413c product 0x0058, class 9/0, rev 2.00/0.00, addr 2
device_probe_and_attach: uhub3 attach returned 6
uhub3: vendor 0x413c product 0x0058, class 9/0, rev 2.00/0.00, addr 2
device_probe_and_attach: uhub3 attach returned 6
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xf4fffc00-0xf4ffffff irq 11 at device 29.7 on pci0
ehci_pci_attach: companion usb0
ehci_pci_attach: companion usb1
ehci_pci_attach: companion usb2
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <EHCI (generic) USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: (0x8086) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
usb3: unrecoverable error, controller halted
usb3: blocking intrs 0x10
uhub3: device problem, disabling port 6
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib2: slot 0 INTA is routed to irq 11
pcib2: slot 1 INTA is routed to irq 11
pcib2: slot 3 INTA is routed to irq 11
pci2: <network, ethernet> at device 0.0 (no driver attached)
cbb0: <TI4510 PCI-CardBus Bridge> at device 1.0 on pci2
cbb0: PCI Memory allocated: f6000000
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib2: slot 1 INTA is routed to irq 11
fwohci0: vendor=104c, dev=8029
fwohci0: <1394 Open Host Controller Interface> mem 0xfaff8000-0xfaffbfff,0xfaffd800-0xfaffdfff irq 11 at device 1.1 on pci2
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channel is 4.
fwohci0: EUI64 38:4f:c0:00:08:9c:ec:41
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
if_fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 3a:4f:c0:9c:ec:41
sbp0: <SBP2/SCSI over firewire> on firewire0
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
pci2: <network> at device 3.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH4 UDMA100 controller> port 0xbfa0-0xbfaf,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pcm0: <Intel 82801DB (ICH4)> port 0xbc40-0xbc7f,0xb800-0xb8ff mem 0xf4fff400-0xf4fff4ff,0xf4fff800-0xf4fff9ff irq 11 at device 31.5 on pci0
pcm0: <SigmaTel STAC9750/51 AC97 Codec>
pci0: <simple comms> at device 31.6 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 1 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/7 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
orm0: <Option ROMs> at iomem 0xcf800-0xcffff,0xc0000-0xcf7ff on isa0
pmtimer0 on isa0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
cbb0: card inserted: event=0x00000000, state=30000820
cbb0: cbb_power: 3V
cardbus0: Resource not specified in CIS: id=10, size=2000
cardbus0: Non-prefetchable memory at f6002000-f6003fff
cardbus0: <network, ethernet> at device 0.0 (no driver attached)
cbb0: cbb_power: 0V
cbb0: CardBus card activation failed
ata1-slave: timeout waiting for interrupt
ata1-slave: ATA identify failed
ad0: 57231MB <FUJITSU MHS2060AT> [116280/16/63] at ata0-master UDMA100
acd0: CD-RW <PHILIPS DVD+RW SDVD6004> at ata1-master WDMA2
Mounting root from ufs:/dev/ad0s3a
cd0 at ata1 bus 0 target 0 lun 0
cd0: <PHILIPS DVD+RW SDVD6004 0.99> Removable CD-ROM SCSI-0 device 
cd0: 16.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
cbb0: card inserted: event=0x00000002, state=30000820
cbb0: cbb_power: 3V
TUPLE: LINKTARGET [3]: 43 49 53
Product version: 5.0
Product name: INTEL(R) | PRO/100 CARDBUS II | MBLA3300 | 1.00 | 
TUPLE: Unknown(0x88) [4]: 2b 82 49 00
TUPLE: Unknown(0x8a) [12]: 39 30 30 32 39 47 34 39 38 32 32 42
TUPLE: Unknown(0x8b) [4]: 00 00 00 00
Manufacturer ID: 89000301c1
TUPLE: DATE [4]: 2a 65 84 2a
Functions: Network Adaptor, Multi-Functioned
Function Extension: 040600034749822b
Function Extension: 0102
Function Extension: 0280969800
Function Extension: 0200e1f505
TUPLE: DEVICE_OC [2]: 02 ff
cardbus0: Opening BAR: type=MEM, bar=10, len=1000 (Prefetchable)
cardbus0: Opening BAR: type=IO, bar=14, len=0040
cardbus0: Opening BAR: type=MEM, bar=18, len=20000 (Prefetchable)
CIS reading done
cardbus0: Prefetchable memory at f6020000-f6040fff
cardbus0: IO port at 1000-103f
fxp0: <Intel 82557/8/9 EtherExpress Pro/100(B) Ethernet> port 0x1000-0x103f mem 0xf6020000-0xf603ffff,0xf6040000-0xf6040fff irq 11 at device 0.0 on cardbus0
fxp0: Ethernet address 00:03:47:49:82:2b
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.