Re: IBM X24 and PCMCIA

Lutz Bichler <[email protected]>
Newsgroups gmane.os.freebsd.devel.mobile
Organization University of the Federal Armed Forces Munich
Message-ID <[email protected]> 
On Thursday 31 July 2003 19:58, Kevin Oberman wrote:
> You probably need to add:
> hw.cbb.start_memory="0x20000000"
> to /boot/loader.conf. You might also need
> hw.pci.allow_unsupported_io_range="1" and
> hw.ata.atapi_dma="1"
> (The last is not related to this problem, but is important if you want
> to get decent performance from a CD reader.)
>
> Use NEWCARD. I am guessing that you meant pccardd on the fatal
> message. If that's the case, don't worry on NEWCARD as pccardd is not
> used with NEWCARD. You do still need pccard_enable="YES" in rc.config.
>
> If you still can't get things working, be sure to include your dmesg
> in further inquiries.

Hi,

i have done the things you suggested but it still does not work. I have the 
demsg attached. The drive is a Hitachi DVD-ROM, Model No. GDR-8081N in an IBM 
Portable Drive Bay 2000. This combination worked under 4.8 using the PCMCIA 
adapter. Alternatively i can attach the drive using USB. But then i get 

umass0: USB to IDE USB to IDE, rev 1.10/2.60, addr 2
(probe0:umass-sim0:0:0:0): INQUIRY. CDB: 12 0 0 0 24 0 
(probe0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(probe0:umass-sim0:0:0:0): SCSI Status: Check Condition
(probe0:umass-sim0:0:0:0): error code 64 at block no. 134217984 (decimal)
(probe0:umass-sim0:0:0:0): No Recovery Action Needed


and things do not work. Any more ideas what i could try?

Lutz

_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"
boot (text/plain, 7.3 KB) 
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.1-RELEASE #52: Thu Jul 31 19:46:51 CEST 2003
    [email protected]:/usr/obj/usr/src/sys/CHRYSAOR
Preloaded elf kernel "/boot/kernel/kernel" at 0xc048c000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc048c244.
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 1129574146 Hz
CPU: Intel(R) Pentium(R) III Mobile CPU      1133MHz (1129.57-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x6b1  Stepping = 1
  Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory  = 267845632 (255 MB)
avail memory = 255164416 (243 MB)
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <IBM    TP-1D   > on motherboard
pcibios: BIOS version 2.10
Using $PIR table, 14 entries at 0xc00fdeb0
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.FDC_._INI] (Node 0xc25f3ac0), AE_NOT_EXIST
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__._INI] (Node 0xc25ec8c0), AE_NOT_EXIST
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI-fast"  frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> port 0x530-0x537 on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
    ACPI-1287: *** Error: Method execution failed [\\_SB_.LID_._PSW] (Node 0xc0eb7480), AE_NOT_EXIST
acpi_button0: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82830 host to AGP bridge> mem 0xd0000000-0xdfffffff at device 0.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
drm0: <ATI Radeon LY Mobility M6> port 0x3000-0x30ff mem 0xc0100000-0xc010ffff,0xe0000000-0xe7ffffff irq 3 at device 0.0 on pci1
info: [drm] AGP at 0xd0000000 256MB
info: [drm] Initialized radeon 1.8.0 20020828 on minor 0
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x1800-0x181f irq 3 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0x1820-0x183f irq 9 at device 29.1 on pci0
usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> port 0x1840-0x185f irq 5 at device 29.2 on pci0
usb2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
cbb0: <RF5C476 PCI-CardBus Bridge> mem 0x50000000-0x50000fff irq 3 at device 3.0 on pci2
start (50000000) < sc->membase (c0200000)
start (50000000) < sc->pmembase (e8000000)
pccard0: <16-bit PCCard bus> on cbb0
cbb1: <RF5C476 PCI-CardBus Bridge> mem 0x50100000-0x50100fff irq 4 at device 3.1 on pci2
start (50100000) < sc->membase (c0200000)
start (50100000) < sc->pmembase (e8000000)
pccard1: <16-bit PCCard bus> on cbb1
pci2: <network> at device 5.0 (no driver attached)
fxp0: <Intel 82801CAM (ICH3) Pro/100 VE Ethernet> port 0x8000-0x803f mem 0xc0200000-0xc0200fff irq 10 at device 8.0 on pci2
fxp0: Ethernet address 00:d0:59:cc:fc:e8
miibus0: <MII bus> on fxp0
inphy0: <i82562ET 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 UDMA100 controller> port 0x1860-0x186f,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pcm0: <Intel 82801CA (ICH3)> port 0x18c0-0x18ff,0x1c00-0x1cff irq 4 at device 31.5 on pci0
pcm0: <Cirrus Logic CS4299 AC97 Codec>
pci0: <simple comms> at device 31.6 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 8250 or not responding
ppc0 port 0x3bc-0x3c3 irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_acad0: <AC adapter> on acpi0
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
orm0: <Option ROMs> at iomem 0xe0000-0xeffff,0xdc000-0xdffff,0xcd000-0xcdfff,0xcc000-0xccfff,0xc0000-0xcbfff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
ipfw2 initialized, divert enabled, rule-based forwarding enabled, default to deny, logging unlimited
acpi_cpu0: set speed to 100.0%
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
acpi_cmbat0: battery initialization start
acpi_acad0: acline initialization start
ad0: 28615MB <HITACHI_DK23DA-30B> [62016/15/63] at ata0-master UDMA100
acpi_ec0: EcRead: Failed waiting for EC to send data.
    ACPI-0432: *** Error: Handler for [EmbeddedControl] returned AE_ERROR
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__.AC__._PSR] (Node 0xc25ef140), AE_ERROR
acpi_acad0: acline initialization done, tried 1 times
acpi_ec0: EcWaitEventIntr called without EC lock!
acpi_cmbat0: battery initialization done, tried 1 times
Mounting root from ufs:/dev/ad0s1a
acpi_acad0: On Line
WARNING: driver "rtc" used unreserved major device number 202
WARNING: driver "vmmon" used unreserved major device number 200
/dev/vmmon: Module vmmon: registered with major=200 minor=0 tag=$Name: build-570+ $
/dev/vmmon: Module vmmon: initialized
start (20000000) < sc->membase (c0200000)
end (ffffffff) > sc->memlimit (cfffffff)
start (20000000) < sc->pmembase (e8000000)
end (ffffffff) > sc->pmemlimit (cfffffff)
start (20000000) < sc->membase (c0200000)
end (ffffffff) > sc->memlimit (cfffffff)
start (20000000) < sc->pmembase (e8000000)
end (ffffffff) > sc->pmemlimit (cfffffff)
pccard0: <unknown card> (manufacturer=0xffffffff, product=0xffffffff) at function 0
pccard0:    CIS info: PCMCIA, IDE CARD, F1
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.