| Newsgroups |
gmane.os.freebsd.devel.mobile |
| Message-ID |
<[email protected]> |
Hi,
I'm running into a problem wrt PCcards under 5.1.
First, here's what I've got:
Compaq Evo N610c, 1GB RAM, 40GB HD, latest BIOS
SW: FreeBSD 5.1
The problem: The PCCard-slots are recognized upon boot but when I
insert a card into any of the two slots I get an error message,
telling me that there's no pccard slot present.
(excert from /var/log/messages)
Oct 15 09:19:16 beastie pccardd[507]: fatal error: no PC-CARD slots
Oct 15 09:19:23 beastie kernel: pccard0: can't alloc memory to read attributes
Oct 15 09:19:23 beastie kernel: pccard0: CARD ERROR!
Oct 15 09:19:23 beastie kernel: cbb0: PC Card card activation failed
When I try to start pccardd by hand, even using "pccardd -d" it dies
immediately with the same error message.
Please note that this happens independent of the card(s) I use: I've
tried with a Cisco Aironet 350 WLAN-card, an Elsa WLAN-card (old prism
chipset) as well as a Xircom 10/100 Ethernet-Card - these are all
cards that should be well known to FreeBSD.
I've already tried upgrading both kernel and userland to the latest
version (cvsup and the usual build/install procedure) - to no extent;
the error remains the same.
For your reference I'm including the complete boot-log below
(/var/log/messages).
Any ideas what could be wrong here?
TIA for your help,
-ewald
------------------------------ < Cut here > ------------------------------
Oct 15 09:16:07 beastie syslogd: kernel boot file is /boot/kernel/kernel
Oct 15 09:16:07 beastie kernel: Copyright (c) 1992-2003 The FreeBSD Project.
Oct 15 09:16:07 beastie kernel: Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
Oct 15 09:16:07 beastie kernel: The Regents of the University of California. All rights reserved.
Oct 15 09:16:07 beastie kernel: FreeBSD 5.1-RELEASE #0: Thu Jun 5 02:55:42 GMT 2003
Oct 15 09:16:07 beastie kernel: [email protected]:/usr/obj/usr/src/sys/GENERIC
Oct 15 09:16:07 beastie kernel: Preloaded elf kernel "/boot/kernel/kernel" at 0xc06d4000.
Oct 15 09:16:07 beastie kernel: Preloaded elf module "/boot/kernel/acpi.ko" at 0xc06d41f4.
Oct 15 09:16:07 beastie kernel: Timecounter "i8254" frequency 1193182 Hz
Oct 15 09:16:07 beastie kernel: Timecounter "TSC" frequency 1993538372 Hz
Oct 15 09:16:07 beastie kernel: CPU: Mobile Intel(R) Pentium(R) 4 - M CPU 2.00GHz (1993.54-MHz 686-class CPU)
Oct 15 09:16:07 beastie kernel: Origin = "GenuineIntel" Id = 0xf27 Stepping = 7
Oct 15 09:16:07 beastie kernel: Features=0xbfebf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Oct 15 09:16:07 beastie kernel: real memory = 1073545216 (1023 MB)
Oct 15 09:16:07 beastie kernel: avail memory = 1035640832 (987 MB)
Oct 15 09:16:07 beastie kernel: Pentium Pro MTRR support enabled
Oct 15 09:16:07 beastie kernel: npx0: <math processor> on motherboard
Oct 15 09:16:07 beastie kernel: npx0: INT 16 interface
Oct 15 09:16:07 beastie kernel: acpi0: <COMPAQ CPQ00B7 > on motherboard
Oct 15 09:16:07 beastie kernel: pcibios: BIOS version 2.10
Oct 15 09:16:07 beastie kernel: ACPI-0351: *** Error: Could not install PciConfig handler for C045, AE_ALREADY_EXISTS
Oct 15 09:16:07 beastie last message repeated 3 times
Oct 15 09:16:07 beastie kernel: acpi0: power button is handled as a fixed feature programming model.
Oct 15 09:16:07 beastie kernel: Timecounter "ACPI-fast" frequency 3579545 Hz
Oct 15 09:16:07 beastie kernel: acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
Oct 15 09:16:07 beastie kernel: acpi_cpu0: <CPU> on acpi0
Oct 15 09:16:07 beastie kernel: acpi_tz0: <thermal zone> on acpi0
Oct 15 09:16:07 beastie kernel: acpi_tz1: <thermal zone> on acpi0
Oct 15 09:16:07 beastie kernel: pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
Oct 15 09:16:07 beastie kernel: pci0: <ACPI PCI bus> on pcib0
Oct 15 09:16:07 beastie kernel: agp0: <Intel 82845 host to AGP bridge> mem 0x60000000-0x6fffffff at device 0.0 on pci0
Oct 15 09:16:07 beastie kernel: pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
Oct 15 09:16:07 beastie kernel: pci1: <ACPI PCI bus> on pcib1
Oct 15 09:16:07 beastie kernel: pci1: <display, VGA> at device 0.0 (no driver attached)
Oct 15 09:16:07 beastie kernel: pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
Oct 15 09:16:07 beastie kernel: pci2: <ACPI PCI bus> on pcib2
Oct 15 09:16:07 beastie kernel: pci2: <simple comms> at device 4.0 (no driver attached)
Oct 15 09:16:07 beastie kernel: cbb0: <TI1420 PCI-CardBus Bridge> mem 0x40000000-0x40000fff irq 11 at device 6.0 on pci2
Oct 15 09:16:07 beastie kernel: cardbus0: <CardBus bus> on cbb0
Oct 15 09:16:07 beastie kernel: pccard0: <16-bit PCCard bus> on cbb0
Oct 15 09:16:07 beastie kernel: cbb1: <TI1420 PCI-CardBus Bridge> mem 0x40080000-0x40080fff at device 6.1 on pci2
Oct 15 09:16:07 beastie kernel: cardbus1: <CardBus bus> on cbb1
Oct 15 09:16:07 beastie kernel: pccard1: <16-bit PCCard bus> on cbb1
Oct 15 09:16:07 beastie kernel: pcib2: slot 6 INTA is routed to irq 11
Oct 15 09:16:07 beastie kernel: fxp0: <Intel 82801CAM (ICH3) Pro/100 VM Ethernet> port 0x2400-0x243f mem 0x40100000-0x40100fff irq 10 at device 8.0 on pci2
Oct 15 09:16:07 beastie kernel: fxp0: Ethernet address 00:02:a5:c1:24:ef
Oct 15 09:16:07 beastie kernel: miibus0: <MII bus> on fxp0
Oct 15 09:16:07 beastie kernel: inphy0: <i82562ET 10/100 media interface> on miibus0
Oct 15 09:16:07 beastie kernel: inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
Oct 15 09:16:07 beastie kernel: ohci0: <NEC uPD 9210 USB controller> mem 0x40180000-0x40180fff irq 10 at device 14.0 on pci2
Oct 15 09:16:07 beastie kernel: usb0: OHCI version 1.0, legacy support
Oct 15 09:16:07 beastie kernel: usb0: <NEC uPD 9210 USB controller> on ohci0
Oct 15 09:16:07 beastie kernel: usb0: USB revision 1.0
Oct 15 09:16:07 beastie kernel: uhub0: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
Oct 15 09:16:07 beastie kernel: uhub0: 3 ports with 3 removable, self powered
Oct 15 09:16:07 beastie kernel: ohci1: <NEC uPD 9210 USB controller> mem 0x40200000-0x40200fff irq 10 at device 14.1 on pci2
Oct 15 09:16:07 beastie kernel: usb1: OHCI version 1.0, legacy support
Oct 15 09:16:07 beastie kernel: usb1: <NEC uPD 9210 USB controller> on ohci1
Oct 15 09:16:07 beastie kernel: usb1: USB revision 1.0
Oct 15 09:16:07 beastie kernel: uhub1: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
Oct 15 09:16:07 beastie kernel: uhub1: 2 ports with 2 removable, self powered
Oct 15 09:16:07 beastie kernel: pci2: <serial bus, USB> at device 14.2 (no driver attached)
Oct 15 09:16:07 beastie kernel: isab0: <PCI-ISA bridge> at device 31.0 on pci0
Oct 15 09:16:07 beastie kernel: isa0: <ISA bus> on isab0
Oct 15 09:16:07 beastie kernel: atapci0: <Intel ICH3 UDMA100 controller> port 0x4440-0x444f,0-0x3,0-0x7,0-0x3,0-0x7 irq 11 at device 31.1 on pci0
Oct 15 09:16:07 beastie kernel: ata0: at 0x1f0 irq 14 on atapci0
Oct 15 09:16:07 beastie kernel: ata1: at 0x170 irq 15 on atapci0
Oct 15 09:16:07 beastie kernel: pci0: <multimedia, audio> at device 31.5 (no driver attached)
Oct 15 09:16:07 beastie kernel: acpi_cmbat0: <Control method Battery> on acpi0
Oct 15 09:16:07 beastie kernel: acpi_cmbat1: <Control method Battery> on acpi0
Oct 15 09:16:07 beastie kernel: acpi_acad0: <AC adapter> on acpi0
Oct 15 09:16:07 beastie kernel: acpi_button0: <Sleep Button> on acpi0
Oct 15 09:16:07 beastie kernel: acpi_lid0: <Control Method Lid Switch> on acpi0
Oct 15 09:16:07 beastie kernel: atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
Oct 15 09:16:07 beastie kernel: atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
Oct 15 09:16:07 beastie kernel: kbd0 at atkbd0
Oct 15 09:16:07 beastie kernel: psm0: <PS/2 Mouse> irq 12 on atkbdc0
Oct 15 09:16:07 beastie kernel: psm0: model Generic PS/2 mouse, device ID 0
Oct 15 09:16:07 beastie kernel: sio0 port 0x3f8-0x3ff irq 4 on acpi0
Oct 15 09:16:07 beastie kernel: sio0: type 16550A
Oct 15 09:16:07 beastie kernel: fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
Oct 15 09:16:07 beastie kernel: fdc0: FIFO enabled, 8 bytes threshold
Oct 15 09:16:07 beastie kernel: fd0: <1440-KB 3.5" drive> on fdc0 drive 0
Oct 15 09:16:07 beastie kernel: sio1 port 0x100-0x107,0x3e8-0x3ef irq 3 drq 1 on acpi0
Oct 15 09:16:07 beastie kernel: sio1: type 16550A
Oct 15 09:16:07 beastie kernel: ppc0 port 0x778-0x77a,0x378-0x37f irq 7 drq 3 on acpi0
Oct 15 09:16:07 beastie kernel: ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
Oct 15 09:16:07 beastie kernel: ppbus0: <Parallel port bus> on ppc0
Oct 15 09:16:07 beastie kernel: plip0: <PLIP network interface> on ppbus0
Oct 15 09:16:07 beastie kernel: lpt0: <Printer> on ppbus0
Oct 15 09:16:07 beastie kernel: lpt0: Interrupt-driven port
Oct 15 09:16:07 beastie kernel: ppi0: <Parallel I/O> on ppbus0
Oct 15 09:16:07 beastie kernel: orm0: <Option ROM> at iomem 0xc0000-0xcffff on isa0
Oct 15 09:16:07 beastie kernel: pmtimer0 on isa0
Oct 15 09:16:07 beastie kernel: sc0: <System console> at flags 0x100 on isa0
Oct 15 09:16:07 beastie kernel: sc0: VGA <16 virtual consoles, flags=0x300>
Oct 15 09:16:07 beastie kernel: vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Oct 15 09:16:07 beastie kernel: Timecounters tick every 10.000 msec
Oct 15 09:16:07 beastie kernel: acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
Oct 15 09:16:07 beastie kernel: ad0: 38154MB <TOSHIBA MK4019GAX> [77520/16/63] at ata0-master UDMA100
Oct 15 09:16:07 beastie kernel: acd0: CD-RW <HL-DT-STCD-RW/DVD DRIVE GCC-4240N> at ata1-master PIO4
Oct 15 09:16:07 beastie kernel: Mounting root from ufs:/dev/ad0s4a
Oct 15 09:16:27 beastie login: ROOT LOGIN (root) ON ttyv0
Here come the errors:
Oct 15 09:19:16 beastie pccardd[507]: fatal error: no PC-CARD slots
Oct 15 09:19:23 beastie kernel: pccard0: can't alloc memory to read attributes
Oct 15 09:19:23 beastie kernel: pccard0: CARD ERROR!
Oct 15 09:19:23 beastie kernel: cbb0: PC Card card activation failed
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"