Re: thinkpad t40 4.0-stable won't resume

> i get some sort of ATA hang when resuming on a T40p running this
> week's -stable.  google and search of mobile yielded no hints.
> anyone here seen this?

apologies.  left off dmesg.

randy

---

Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 4.9-STABLE #3: Fri Nov 28 18:44:17 PST 2003
    [email protected]:/usr/obj/usr/src/sys/ROAM
Timecounter "i8254"  frequency 1193182 Hz
CPU: Intel(R) Pentium(R) M processor 1600MHz (1594.83-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x695  Stepping = 5
  Features=0xa7e9f9bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,TM,PBE>
real memory  = 1073086464 (1047936K bytes)
avail memory = 1040891904 (1016496K bytes)
Preloaded elf kernel "kernel" at 0xc038d000.
Preloaded elf module "snd_ich.ko" at 0xc038d09c.
Preloaded elf module "snd_pcm.ko" at 0xc038d13c.
Pentium Pro MTRR support enabled
Using $PIR table, 15 entries at 0xc00fdea0
apm0: <APM BIOS> on motherboard
apm0: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
agp0: <Intel 82855 host to AGP bridge> mem 0xd0000000-0xdfffffff at device 0.0 on pci0
pcib1: <PCI to PCI bridge (vendor=8086 device=3341)> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <ATI model 4c66 graphics accelerator> at 0.0 irq 11
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0x1800-0x181f irq 11 at device 29.0 on pci0
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0x1820-0x183f irq 11 at device 29.1 on pci0
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0x1840-0x185f irq 11 at device 29.2 on pci0
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub2: device problem, disabling port 1
pci0: <USB controller> at 29.7 irq 11
pcib2: <PCI to PCI bridge (vendor=8086 device=2448)> at device 30.0 on pci0
pci2: <PCI bus> on pcib2
pcic0: <TI PCI-1520 PCI-CardBus Bridge> mem 0xb0000000-0xb0000fff irq 11 at device 0.0 on pci2
pcic0: TI12XX PCI Config Reg: [speaker enable][pwr save][CSC serial isa irq]
pccard0: <PC Card 16-bit bus (classic)> on pcic0
pcic1: <TI PCI-1520 PCI-CardBus Bridge> mem 0xb1000000-0xb1000fff irq 11 at device 0.1 on pci2
pcic1: TI12XX PCI Config Reg: [speaker enable][pwr save][CSC serial isa irq]
pccard1: <PC Card 16-bit bus (classic)> on pcic1
em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.19> port 0x8000-0x803f mem 0xc0200000-0xc020ffff,0xc0220000-0xc023ffff irq 11 at device 1.0 on pci2
em0:  Speed:N/A  Duplex:N/A
pci2: <unknown card> (vendor=0x168c, dev=0x0012) at 2.0 irq 11
isab0: <PCI to ISA bridge (vendor=8086 device=24cc)> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Generic PCI ATA controller> port 0x1860-0x186f,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <unknown card> (vendor=0x8086, dev=0x24c3) at 31.3 irq 11
pcm0: <Intel ICH4 (82801DB)> port 0x18c0-0x18ff,0x1c00-0x1cff mem 0xc0000800-0xc00008ff,0xc0000c00-0xc0000dff irq 11 at device 31.5 on pci0
pcm0: <Analog Devices AD1981B AC97 Codec>
pci0: <unknown card> (vendor=0x8086, dev=0x24c6) at 31.6 irq 11
eisa0: <EISA bus> on motherboard
eisa0: unknown card @@@0000 (0x00000000) at slot 1
orm0: <Option ROMs> at iomem 0xc0000-0xcffff,0xdc000-0xdffff,0xe0000-0xeffff on isa0
pmtimer0 on isa0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: cannot reserve I/O port range
IP packet filtering initialized, divert enabled, rule-based forwarding enabled, default to deny, logging limited to 100 packets/entry by default
IPsec: Initialized Security Association Processing.
pccard: card inserted, slot 0
pccard: card removed, slot 0
ad0: 54164MB <HTS726060M9AT00> [110048/16/63] at ata0-master BIOSDMA
Mounting root from ufs:/dev/ad0s3a
pccard: card inserted, slot 0
an0: <Aironet PC4500/PC4800> at port 0x240-0x27f irq 11 slot 0 on pccard0
an0: got RSSI <-> dBM map
an0: Ethernet address: 00:07:0e:b9:8a:f3

_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"