Proxim Harmony Installation Problems

Hi!

I bought a Proxim Harmony PCI 802.11b and tried to install it under
FreeBSD 4.9 .

The Problem ist that FreeBSD does not create a wi Interface when it comes
up. The Card has a PCI to PCMCIA bridge which is recognized. I have built
in the Kernel the wi device and pccardd support.

Here some output of several Programs:

> root@zeus:~> scanpci

pci bus 0x0000 cardnum 0x00 function 0x00: vendor 0x1022 device 0x7006
 Advanced Micro Devices [AMD] AMD-751 [Irongate] System Controller

pci bus 0x0000 cardnum 0x01 function 0x00: vendor 0x1022 device 0x7007
 Advanced Micro Devices [AMD] AMD-751 [Irongate] AGP Bridge

pci bus 0x0000 cardnum 0x07 function 0x00: vendor 0x1022 device 0x7408
 Advanced Micro Devices [AMD] AMD-756 [Viper] ISA

pci bus 0x0000 cardnum 0x07 function 0x01: vendor 0x1022 device 0x7409
 Advanced Micro Devices [AMD] AMD-756 [Viper] IDE

pci bus 0x0000 cardnum 0x07 function 0x03: vendor 0x1022 device 0x740b
 Advanced Micro Devices [AMD] AMD-756 [Viper] ACPI

pci bus 0x0000 cardnum 0x07 function 0x04: vendor 0x1022 device 0x740c
 Advanced Micro Devices [AMD] AMD-756 [Viper] USB

pci bus 0x0000 cardnum 0x08 function 0x00: vendor 0x10b7 device 0x9200
 3Com Corporation 3c905C-TX/TX-M [Tornado]

pci bus 0x0000 cardnum 0x09 function 0x00: vendor 0x9005 device 0x0081
 Adaptec AIC-7892B U160/m

pci bus 0x0000 cardnum 0x0a function 0x00: vendor 0x10b7 device 0x7646
 3Com Corporation 3cSOHO100-TX Hurricane

pci bus 0x0000 cardnum 0x0b function 0x00: vendor 0x1013 device 0x1100
 Cirrus Logic CL 6729

pci bus 0x0001 cardnum 0x05 function 0x00: vendor 0x10de device 0x0020
 nVidia Corporation NV4 [RIVA TNT]
root@zeus:~>


> root@zeus:~> pccardc dumpcis
Configuration data for card in slot 0
Tuple #1, code = 0x1 (Common memory descriptor), length = 3
    000:  00 00 ff
        Common memory device information:
                Device number 1, type No device, WPS = OFF
                Speed = No speed, Memory block size = 512b, 1 units
Tuple #2, code = 0x17 (Attribute memory descriptor), length = 4
    000:  67 5a 08 ff
        Attribute memory device information:
                Device number 1, type SRAM, WPS = OFF
                Speed = 5.0 x 100 ns, Memory block size = 512b, 2 units
Tuple #3, code = 0x1d (Other conditions for attribute memory), length = 5
    000:  03 67 5a 08 ff
        (MWAIT) (3V card)
Tuple #4, code = 0x15 (Version 1 info), length = 80
    000:  05 00 50 52 4f 58 49 4d 00 4c 41 4e 20 50 43 49
    010:  20 43 41 52 44 20 48 41 52 4d 4f 4e 59 20 38 30
    020:  32 31 31 42 00 00 00 00 00 00 00 00 00 00 00 00
    030:  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
    040:  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ff
        Version = 5.0, Manuf = [PROXIM], card vers = [LAN PCI CARD HARMONY
80211B]
        Addit. info = [],[]
Tuple #5, code = 0x20 (Manufacturer ID), length = 4
    000:  26 01 02 00
        PCMCIA ID = 0x126, OEM ID = 0x2
Tuple #6, code = 0x21 (Functional ID), length = 2
    000:  06 00
        Network/LAN adapter
Tuple #7, code = 0x22 (Functional EXT), length = 2
    000:  01 07
        Network technology: Wireless
Tuple #8, code = 0x22 (Functional EXT), length = 5
    000:  02 40 42 0f 00
        Network speed: 1 Mb/sec
Tuple #9, code = 0x22 (Functional EXT), length = 5
    000:  02 80 84 1e 00
        Network speed: 2 Mb/sec
Tuple #10, code = 0x22 (Functional EXT), length = 5
    000:  02 60 ec 53 00
        Network speed: 5 Mb/sec
Tuple #11, code = 0x22 (Functional EXT), length = 5
    000:  02 c0 d8 a7 00
        Network speed: 11 Mb/sec
Tuple #12, code = 0x22 (Functional EXT), length = 2
    000:  03 07
        Network media: 2.4 GHz
Tuple #13, code = 0x22 (Functional EXT), length = 8
    000:  04 06 00 00 f0 64 00 00
        Network node ID: 00 00 f0 64 00 00
Tuple #14, code = 0x22 (Functional EXT), length = 2
    000:  05 01
        Network connector: closed connector standard
Tuple #15, code = 0x1a (Configuration map), length = 7
    000:  03 01 e0 03 00 00 01
        Reg len = 4, config register addr = 0x3e0, last config = 0x1
        Registers: X-------
Tuple #16, code = 0x1b (Configuration entry), length = 13
    000:  c1 01 09 77 b5 1e 35 b5 3c 36 36 05 46
        Config index = 0x1(default)
        Interface byte = 0x1 (I/O)
        Vcc pwr:
                Nominal operating supply voltage: 3 x 1V, ext = 0x1e
                Minimum operating supply voltage: 3 x 1V
                Maximum operating supply voltage: 3 x 1V, ext = 0x3c
                Max current average over 1 second: 3 x 100mA
                Max current average over 10 ms: 3 x 100mA
                Power down supply current: 1 x 10mA
        Card decodes 6 address lines, limited 8/16 Bit I/O
Tuple #17, code = 0xff (Terminator), length = 0
2 slots found
root@zeus:~>

> root@zeus:~> less /boot/loader.conf
userconfig_script_load="YES"
autoboot_delay="2"
hw.pcic.pd6729_intr_path="2"
root@zeus:~>

> root@zeus:~> ifconfig -a
xl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
        options=3<rxcsum,txcsum>
        inet 192.168.1.1 netmask 0xffffff00 broadcast 192.168.1.255
        inet6 fe80::204:76ff:fe8d:58d3%xl0 prefixlen 64 scopeid 0x1
        ether 00:04:76:8d:58:d3
        media: Ethernet autoselect (100baseTX <full-duplex>)
        status: active
xl1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
        options=3<rxcsum,txcsum>
        inet 10.0.0.1 netmask 0xff000000 broadcast 10.255.255.255
        inet6 fe80::204:76ff:fe8c:f7d7%xl1 prefixlen 64 scopeid 0x2
        ether 00:04:76:8c:f7:d7
        media: Ethernet autoselect (100baseTX <full-duplex>)
        status: active
lp0: flags=8810<POINTOPOINT,SIMPLEX,MULTICAST> mtu 1500
faith0: flags=8002<BROADCAST,MULTICAST> mtu 1500
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
        inet6 ::1 prefixlen 128
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5
        inet 127.0.0.1 netmask 0xff000000
ppp0: flags=8010<POINTOPOINT,MULTICAST> mtu 1500
sl0: flags=c010<POINTOPOINT,LINK2,MULTICAST> mtu 552
ipr0: flags=2810<POINTOPOINT,SIMPLEX,LINK1> mtu 1500
ipr1: flags=2810<POINTOPOINT,SIMPLEX,LINK1> mtu 1500
ipr2: flags=2810<POINTOPOINT,SIMPLEX,LINK1> mtu 1500
ipr3: flags=2810<POINTOPOINT,SIMPLEX,LINK1> mtu 1500
isp0: flags=8010<POINTOPOINT,MULTICAST> mtu 1500
        ether 00:00:00:00:00:00
isp1: flags=8010<POINTOPOINT,MULTICAST> mtu 1500
        ether 00:00:00:00:00:00
isp2: flags=8010<POINTOPOINT,MULTICAST> mtu 1500
        ether 00:00:00:00:00:00
isp3: flags=8010<POINTOPOINT,MULTICAST> mtu 1500
        ether 00:00:00:00:00:00
tun0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1500
        inet 62.245.233.95 --> 62.245.233.1 netmask 0xffffffff
        Opened by PID 59598
root@zeus:~>

If someone has an idea please let me know.

Regards,
           Oliver
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"