Re: ACPI/PCI-bus issue with compaq evo n160

The solution suggested by Mauritz worked, the ACPI stuff works now. 
This is what I have in my loader.conf

debug.acpi.disable="lid pci_link"
hw.pci.allow_unsupported_io_range="1"
hw.cbb.start_memory="536870912"

I would like to thank everybody who have helped me troubleshoot this.

   Fredrik

(please remove the NOSPAM stuff if you reply private)

On Wed, Dec 17, 2003 at 10:02:43AM +0100, Mauritz Sundell (mauritz.sundell) wrote:
> 
> It is enough to disable pci_link for booting
> debug.acpi.disable="pci_link"
> 
> But I also disable lid because otherwise it goes to some kind of sleep (S1) when I close the lid.
> debug.acpi.disable="lid pci_link"
> 
> Also for I have
> hw.cbb.start_memory="0xd0208000"
> since pci/pcib allocates the memory assigned to fxp0 by BIOS to pccard otherwise.
> 
> Now I always use acpiconf -s S4 to suspend and save to disk instead of turning the power off, wonderful.
> 
> 
> -----Original Message-----
> From: Fredrik Lindberg <>
> To: [email protected]
> Date: Fri, 12 Dec 2003 15:28:56 +0100
> Subject: ACPI/PCI-bus issue with compaq evo n160
> 
> Hi,
> Thank you for your reply.
> The information you requested is avaiable at
> 
> http://shapeshifter.se/~fredde/tmp/db
> http://shapeshifter.se/~fredde/tmp/dmesg.acpi-pci.enabled
> 
>   Fredrik 
> 
> On Thu, Dec 11, 2003 at 01:42:06PM -0500, John Baldwin (jhb) wrote:
> > [ Resent due to NO.*SPAM bounce the first time ]
> > 
> > On 10-Dec-2003 Fredrik Lindberg wrote:
> > > Hi,
> > > 
> > > I have a Compaq evo n160 running 
> > > FreeBSD biocandy 5.2-RC FreeBSD 5.2-RC #10: Mon Dec  8 19:08:38 CET 2003
> > > 
> > > The machine fails (and always has) to boot with acpi enabled 
> > > (locks up when mounting /), however, I managed to find out that 
> > > booting with the following option 
> > > 
> > > debug.acpi.disable="pci" 
> > > 
> > > in /boot/loader.conf made the machine boot correctly and acpi related 
> > > functions such as battry monitoring worked just fine.
> > > 
> > > But, and a huge but, no pci devices are detected during boot 
> > > (maybe quite obvious because of that debug option) 
> > > All pci-devices works perfectly with acpi disabled.
> > > 
> > > Now, is there any chance to make freebsd use acpi and the 
> > > "normal" pci-bus driver at the same time, overriding the 
> > > acpi pci-bus implementation?
> > > 
> > > I believe linux has a kernel option called pci=noacpi (atleast acording to google),
> > > which does this.
> > > 
> > > With acpi enabled scanpci reports all the pci devices, but pciconf -l
> > > doesn't return anything.
> > > With acpi disabled, scanpci reports all pci devices, pciconf -l 
> > > reports all devices.
> > > 
> > > dmesg output with acpi enabled 
> > > http://shapeshifter.se/~fredde/tmp/dmesg.acpi.enabled
> > > 
> > > dmesg out with acpi disabled
> > > http://shapeshifter.se/~fredde/tmp/dmesg.acpi.disabled
> > > 
> > > Any, and I mean any, help on this will be very appreciated.
> > 
> > If you can drop into ddb and do a 'show intrcnt' when the machine
> > locks up that might help fix the hang.  It sounds like the interrupt
> > routing may not have worked correctly.  Also, a dmesg of acpi
> > with pci enabled would be helpful.
> > 
> > -- 
> > 
> > John Baldwin <jhb>  <><  http://www.FreeBSD.org/~jhb/
> > "Power Users Use the Power to Serve!"  -  http://www.FreeBSD.org/
> 
> ----- End forwarded message -----
> _______________________________________________
> freebsd-mobile mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
> To unsubscribe, send any mail to "freebsd-mobile-unsubscribe"
> 
> 
> 


_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"