Re: wi0 busy bit won't clear error

> From: Jesse Guardiani <[email protected]>
> Date: Sun, 15 Feb 2004 16:39:10 -0500
> Sender: [email protected]
> 
> Howdy list,
> 
> For some time now I've been having intermittent problems
> with my wireless card. Occasionally I'll get the following
> message on my console and all wireless traffic will stop,
> forcing me to reboot:
> 
> Dec 29 12:14:51 trevarthan kernel: wi0: timeout in wi_cmd 0x010b; event status 0x8000
> Dec 29 12:14:51 trevarthan kernel: wi0: xmit failed
> Dec 29 12:14:52 trevarthan kernel: wi0: timeout in wi_cmd 0x0021; event status 0x8000
> Dec 29 12:14:57 trevarthan kernel: wi0: wi_cmd: busy bit won't clear.
> 
> I've seen a few other complaints about this on various
> FreeBSD mailling lists, but no solution. Sometimes, the
> user is asked to upgrade his/her firmware.
> 
> I took a look at my firmware on Friday, and sure enough
> I had old old firmware:
> 
> wi0: <Intersil Prism2.5> mem 0xf0000000-0xf0000fff irq 9 at device 2.0 on pci2
> pcib2: device wi0 requested decoded memory range 0xf0000000-0xf0000fff
> wi0: 802.11 address: 00:20:e0:8a:90:61
> wi0: using RF:PRISM2.5 MAC:ISL3874A(Mini-PCI)
> wi0: Intersil Firmware: Primary (1.1.0), Station (1.4.2)
> wi0: bpf attached
> wi0: bpf attached
> wi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
> wi0: bpf attached
> 
> So... I decided to upgrade. I noticed that M. Warner had
> been recommending 1.4.9, and that the `wi` man page also
> recommended it, so I upgraded to 1.4.9:
> 
> wi0: <Intersil Prism2.5> mem 0xf0000000-0xf0000fff irq 9 at device 2.0 on pci2
> pcib2: device wi0 requested decoded memory range 0xf0000000-0xf0000fff
> wi0: 802.11 address: 00:20:e0:8a:90:61
> wi0: using RF:PRISM2.5 MAC:ISL3874A(Mini-PCI)
> wi0: Intersil Firmware: Primary (1.1.0), Station (1.4.9)
> wi0: bpf attached
> wi0: bpf attached
> wi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
> wi0: bpf attached
> 
> wi DOES seem more stable now. However, just this morning I
> got the same message:
> 
> wi0: timeout in wi_seek to 127/0
> wi0: timeout in wi_seek to 127/0
> wi0: timeout in wi_cmd 0x0021; event status 0x8000
> wi0: timeout in wi_seek to 127/0
> wi0: timeout in wi_seek to 127/0
> wi0: wi_cmd: busy bit won't clear.
> 
> With the same results. I had to reboot to fix it.
> 
> Here's what `ifconfig wi0` looked like after I encountered
> the busy bit message:
> 
> wi0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>         inet6 fe80::220:e0ff:fe8a:9061%wi0 prefixlen 64 scopeid 0x2
>         inet 192.168.1.101 netmask 0xffffff00 broadcast 192.168.1.255
>         ether 00:20:e0:8a:90:61
> 
> And here's what it looks like normally:
> 
> wi0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>         inet6 fe80::220:e0ff:fe8a:9061%wi0 prefixlen 64 scopeid 0x2
>         inet 192.168.1.101 netmask 0xffffff00 broadcast 192.168.1.255
>         ether 00:20:e0:8a:90:61
>         media: IEEE 802.11 Wireless Ethernet autoselect (DS/11Mbps)
>         status: associated
>         ssid TREVARTHAN 1:TREVARTHAN
>         stationname "FreeBSD WaveLAN/IEEE node"
>         channel 6 authmode OPEN powersavemode OFF powersavesleep 100
>         wepmode MIXED weptxkey 1
>         wepkey 1:104-bit
> 
> Here's my `pciconf -lv | grep -A 3 wi0` output:
> 
> wi0@pci2:2:0:   class=0x028000 card=0x04061668 chip=0x38731260 rev=0x01 hdr=0x00
>     vendor   = 'Intersil Americas Inc (Was: Harris Semiconductor)'
>     device   = 'PRISM 2.5 802.11b 11Mbps Wireless Controller'
>     class    = network
> 
> And here's my `uname -a`:
> 
> FreeBSD trevarthan.int.wingnet.net 5.2.1-RC2 FreeBSD 5.2.1-RC2 #0: Thu Feb 12 16:28:31 GMT 2004     [email protected]:/usr/obj/usr/src/sys/GENERIC  i386
> 
> 
> Is anyone else experiencing this problem with wi and a relatively
> current firmware? Does anyone NOT experience this problem with
> a particular firmware? If so, please let me know so I can upgrade to
> that firmware version.
> 
> I hate rebooting my machine. It makes me feel like I'm running windows
> again. So if anyone could give me info that would help me prevent this
> problem then I would be very appreciative.
> 

Have you applied the patch to add the DELAY(1) macros after reading the
CSR to the wi driver?  It was posted to mobile@ back around Jan. 10 by
Marco Zec. Since I installed that patch, I have not had any of these
timeout issues.
-- 
R. Kevin Oberman, Network Engineer
Energy Sciences Network (ESnet)
Ernest O. Lawrence Berkeley National Laboratory (Berkeley Lab)
E-mail: [email protected]			Phone: +1 510 486-8634
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"