wi0/Prism2.5: problems after upgrade 4.8 -> 4.9

Hi,

after upgrade from 4.8 to 4.9 my Prism2.5-based wi0 (Netgear
MA311, hostap) no longer works - IPsec or WEP disabled.  Output
of dmesg is below.

Strange enough, a ping from another box to the AP shows that
ICMP goes only in one direction:

	kruemel# tcpdump -i wi0
    tcpdump: listening on wi0
    22:57:08.812073 other-box > freebsd-ap: icmp: echo request (DF)
    22:57:09.807063 other-box > freebsd-ap: icmp: echo request (DF)
    22:57:10.806939 other-box > freebsd-ap: icmp: echo request (DF)

So, this looks to me like a driver problem.

Thanks in advance.

/Holger


FreeBSD 4.9-RELEASE #0: Sat Mar 13 21:54:14 CET 2004
    [email protected]:/usr/src/sys/compile/KRUEMEL
Timecounter "i8254"  frequency 1193182 Hz
CPU: VIA C3 Samuel 2 (533.35-MHz 686-class CPU)
  Origin = "CentaurHauls"  Id = 0x673  Stepping = 3
  Features=0x803035<FPU,DE,TSC,MSR,MTRR,PGE,MMX>
real memory  = 260046848 (253952K bytes)
avail memory = 248938496 (243104K bytes)
Preloaded elf kernel "kernel" at 0xc0406000.
md0: Malloc disk
Using $PIR table, 5 entries at 0xc00fdc70
apm0: <APM BIOS> on motherboard
apm0: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
agp0: <VIA Generic host to PCI bridge> mem 0xd0000000-0xd1ffffff at device 0.0 on pci0
pcib1: <PCI to PCI bridge (vendor=1106 device=8601)> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <Trident model 8500 VGA-compatible display device> at 0.0 irq 11
isab0: <PCI to ISA bridge (vendor=1106 device=8231)> at device 17.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 8231 ATA100 controller> port 0xc000-0xc00f at device 17.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <VIA 83C572 USB controller> port 0xc400-0xc41f irq 5 at device 17.2 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0xc800-0xc81f irq 5 at device 17.3 on pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
chip0: <PCI to Other bridge (vendor=1106 device=8235)> at device 17.4 on pci0
chip1: <VIA 82C686 AC97 Audio> port 0xd400-0xd403,0xd000-0xd003,0xcc00-0xccff irq 12 at device 17.5 on pci0
vr0: <VIA VT6102 Rhine II 10/100BaseTX> port 0xd800-0xd8ff mem 0xd6002000-0xd60020ff irq 11 at device 18.0 on pci0
vr0: Ethernet address: 00:40:63:c9:bf:50
miibus0: <MII bus> on vr0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
wi0: <Intersil Prism2.5> mem 0xd6000000-0xd6000fff irq 11 at device 19.0 on pci0
wi0: 802.11 address: 00:09:5b:91:8c:70
wi0: using RF:PRISM2.5 MAC:ISL3874A(Mini-PCI)
wi0: Intersil Firmware: Primary 1.01.01, Station 1.05.06
isic0: <ELSA MicroLink ISDN/PCI> port 0xe000-0xe003,0xdc00-0xdc7f mem 0xd6001000-0xd600107f irq 10 at device 20.0 on pci0
isic0: passive stack unit 0
orm0: <Option ROM> at iomem 0xc0000-0xcbfff on isa0
pmtimer0 on isa0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
i4bctl: ISDN system control port attached
i4btrc: 2 ISDN trace device(s) attached
i4bisppp: 2 ISDN SyncPPP device(s) attached
i4b: ISDN call control device attached
IP packet filtering initialized, divert enabled, rule-based forwarding enabled, default to deny, logging disabled
i4btel: 2 ISDN telephony interface device(s) attached
i4brbch: 4 raw B channel access device(s) attached
i4bipr: 2 IP over raw HDLC ISDN device(s) attached (VJ header compression)
IPsec: Initialized Security Association Processing.
ad0: 28615MB <FUJITSU MHT2030AT> [58140/16/63] at ata0-master UDMA100
Mounting root from ufs:/dev/ad0s1a
i4b: unit 0, assigned TEI = 108 = 0x6c
isp0: lcp: RXJ- (proto-rej) for proto 0x57 (unknown/?)
isp0: lcp: RXJ- (proto-rej) for proto 0x57 (unknown/?)
wi0: promiscuous mode enabled
wi0: promiscuous mode disabled
wi0: promiscuous mode enabled
wi0: timeout in wi_seek to 14c/3c; last status 403c

-- 
++ GnuPG Key -> http://www.t-online.de/~holger.eitzenberger ++

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.4 (GNU/Linux)

iD8DBQFAWMwdwVlL9V2akAURAnJcAJ9B9u0THFYbgz8dsmHw2pI8h7H3VQCfQKji
zLHC2OdSsah8nFztqzUrXNQ=
=kly/
-----END PGP SIGNATURE-----