no pccard , agp hangs on medion laptop

Hi all,

After an complex install:

problem 1: 
install cd hangs on agp,
I tried:
1. install without acpi -> no joy
2. single user, with acpi.ko not loaded -> no joy
3. install 5.1 -> no joy
4. install 4.7 -> yes

Then I copied an 5.2.1 install from remote. I rsynced via ad0s1a 4.7 to
ad0s2. Of cource with a kernel without agp!

To check if thing work I did a make world and a new kernel --> ok

My question: can I help debugging the agp issue? pciconf is below.


Problem 2:

when I enter a 802.11b card ( prism 2,5 or harris chip) no wi<x> is
found.

and no pccard is found in /dev

pccardd says in /var/log/messages:

Jun  5 18:07:20 medion pccardd[75253]: fatal error: no PC-CARD slots
Jun  5 18:07:32 medion pccardd[75255]: fatal error: no PC-CARD slots
Jun  5 19:13:51 medion pccardd[18492]: fatal error: no PC-CARD slots

more data below:

Thanks,
Marten

 medion# pciconf -l -v
hostb0@pci0:0:0:        class=0x060000 card=0x403217c0 chip=0x25708086
rev=0x02 hdr=0x00
    vendor   = 'Intel Corporation'
    device   = '82865G/PE/P, 82848P DRAM Controller / Host-Hub
Interface'
    class    = bridge
    subclass = HOST-PCI
pcib1@pci0:1:0: class=0x060400 card=0x00000000 chip=0x25718086 rev=0x02
hdr=0x01
    vendor   = 'Intel Corporation'
    device   = '82865G/PE/P, 82848P PCI-to-AGP Bridge'
    class    = bridge
    subclass = PCI-PCI
uhci0@pci0:29:0:        class=0x0c0300 card=0x402717c0 chip=0x24d28086
rev=0x02 hdr=0x00
    vendor   = 'Intel Corporation'
    device   = '82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1'
    class    = serial bus
    subclass = USB
uhci1@pci0:29:1:        class=0x0c0300 card=0x402717c0 chip=0x24d48086
rev=0x02 hdr=0x00
    vendor   = 'Intel Corporation'
    device   = '82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2'
    class    = serial bus
    subclass = USB
uhci2@pci0:29:2:        class=0x0c0300 card=0x402717c0 chip=0x24d78086
rev=0x02 hdr=0x00
    vendor   = 'Intel Corporation'
    device   = '82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3'
    class    = serial bus
    subclass = USB
uhci3@pci0:29:3:        class=0x0c0300 card=0x402717c0 chip=0x24de8086
rev=0x02 hdr=0x00
    vendor   = 'Intel Corporation'
    device   = '82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4'
    class    = serial bus
    subclass = USB
none0@pci0:29:7:        class=0x0c0320 card=0x109617c0 chip=0x24dd8086
rev=0x02 hdr=0x00
    vendor   = 'Intel Corporation'
    device   = '82801EB/ER (ICH4/ICH5R) USB EHCI Controller'
    class    = serial bus
    subclass = USB
pcib2@pci0:30:0:        class=0x060400 card=0x00000000 chip=0x244e8086
rev=0xc2 hdr=0x01
    vendor   = 'Intel Corporation'
    device   = '82801BA/CA/DB/EB/ER (ICH2/3/4/5/5R) Hub Interface to PCI
Bridge'
    class    = bridge
    subclass = PCI-PCI
isab0@pci0:31:0:        class=0x060100 card=0x00000000 chip=0x24d08086
rev=0x02 hdr=0x00
    vendor   = 'Intel Corporation'
    device   = '82801EB/ER (ICH5/ICH5R) LPC Interface Bridge'
    class    = bridge
    subclass = PCI-ISA
atapci0@pci0:31:1:      class=0x01018a card=0x402717c0 chip=0x24db8086
rev=0x02 hdr=0x00
    vendor   = 'Intel Corporation'
    device   = '82801EB/ER (ICH5/ICH5R) EIDE Controller'
    class    = mass storage
    subclass = ATA
none1@pci0:31:3:        class=0x0c0500 card=0x402717c0 chip=0x24d38086
rev=0x02 hdr=0x00
    vendor   = 'Intel Corporation'
    device   = '82801EB/ER (ICH5/ICH5R) SMBus Controller'
    class    = serial bus
    subclass = SMBus
none2@pci0:31:5:        class=0x040100 card=0x201017c0 chip=0x24d58086
rev=0x02 hdr=0x00
    vendor   = 'Intel Corporation'
    device   = '82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller'
    class    = multimedia
    subclass = audio
none3@pci0:31:6:        class=0x070300 card=0x109c17c0 chip=0x24d68086
rev=0x02 hdr=0x00
    vendor   = 'Intel Corporation'
    device   = '82801EB/ER (ICH5/ICH5R) AC'97 Modem Controller'
    class    = simple comms
none4@pci1:0:0: class=0x030000 card=0x206f17c0 chip=0x032c10de rev=0xa1
hdr=0x00
    vendor   = 'NVIDIA Corporation'
    class    = display
    subclass = VGA
none5@pci3:4:0: class=0x060700 card=0x17c017c0 chip=0xac8e104c rev=0x00
hdr=0x02
    vendor   = 'Texas Instruments (TI)'
    class    = bridge
    subclass = PCI-CardBus
none6@pci3:4:1: class=0x060700 card=0x17c017c0 chip=0xac8e104c rev=0x00
hdr=0x02
    vendor   = 'Texas Instruments (TI)'
    class    = bridge
    subclass = PCI-CardBus
fwohci0@pci3:4:2:       class=0x0c0010 card=0x109517c0 chip=0x802e104c
rev=0x00 hdr=0x00
    vendor   = 'Texas Instruments (TI)'
    class    = serial bus
    subclass = FireWire
none7@pci3:4:3: class=0x018000 card=0x300617c0 chip=0xac8f104c rev=0x00
hdr=0x00
    vendor   = 'Texas Instruments (TI)'
    class    = mass storage
rl0@pci3:5:0:   class=0x020000 card=0x105317c0 chip=0x813910ec rev=0x10
hdr=0x00
    vendor   = 'Realtek Semiconductor'
    device   = 'RT8139 (A/B/C/813x/C+) Fast Ethernet Adapter'
    class    = network
    subclass = ethernet
none8@pci3:6:0: class=0x028000 card=0x001417cf chip=0x38901260 rev=0x01
hdr=0x00
    vendor   = 'Intersil Americas Inc (Was: Harris Semiconductor)'
    class    = network
medion#
medion# dmesg
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights
reserved.
FreeBSD 5.2.1-RELEASE-p8 #1: Sat Jun  5 11:57:24 CEST 2004
    [email protected]:/usr/obj/usr/src/sys/mvn
Preloaded elf kernel "/boot/kernel/kernel" at 0xc07cd000.
MPTable: <INTEL    SPDG+ICH5   >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Mobile Intel(R) Pentium(R) 4     CPU 3.06GHz (3059.22-MHz 686-class
CPU)
  Origin = "GenuineIntel"  Id = 0xf29  Stepping = 9
 
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Hyperthreading: 2 logical CPUs
real memory  = 536281088 (511 MB)
avail memory = 515452928 (491 MB)
ioapic0: Assuming intbase of 0
ioapic0 <Version 2.0> irqs 0-23 on motherboard
Pentium Pro MTRR support enabled
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcibios: BIOS version 2.10
Using $PIR table, 9 entries at 0xc00fdda0
pcib0: <MPTable Host-PCI bridge> at pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pcib0: slot 29 INTA routed to irq 16
pcib0: slot 29 INTB routed to irq 19
pcib0: slot 29 INTC routed to irq 18
pcib0: slot 29 INTA routed to irq 16
pcib0: slot 29 INTD routed to irq 23
pcib0: slot 31 INTB routed to irq 17
pcib0: slot 31 INTB routed to irq 17
pcib0: slot 31 INTB routed to irq 17
pcib1: <MPTable PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pcib1: slot 0 INTA routed to irq 16
pci1: <display, VGA> at device 0.0 (no driver attached)
uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0x1cc0-0x1cdf
irq 16 at device 29.0 on pci0
usb0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ums0: Genesys Logic USB Mouse, rev 2.00/1.10, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0x1ce0-0x1cff
irq 19 at device 29.1 on pci0
usb1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0x2000-0x201f
irq 18 at device 29.2 on pci0
usb2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0x2020-0x203f
irq 16 at device 29.3 on pci0
usb3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
pci0: <serial bus, USB> at device 29.7 (no driver attached)
pcib2: <MPTable PCI-PCI bridge> at device 30.0 on pci0
pci3: <PCI bus> on pcib2
pcib2: slot 4 INTC routed to irq 23
pcib2: slot 4 INTD routed to irq 20
pcib2: slot 5 INTA routed to irq 19
pcib2: slot 6 INTA routed to irq 18
cbb0: <PCI-CardBus Bridge> at device 4.0 on pci3
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib2: unable to route slot 4 INTA
cbb: Unable to map IRQ...
device_probe_and_attach: cbb0 attach returned 12
cbb0: <PCI-CardBus Bridge> at device 4.1 on pci3
cardbus1: <CardBus bus> on cbb0
pccard1: <16-bit PCCard bus> on cbb0
pcib2: unable to route slot 4 INTB
cbb: Unable to map IRQ...
device_probe_and_attach: cbb0 attach returned 12
fwohci0: vendor=104c, dev=802e
fwohci0: <1394 Open Host Controller Interface> mem
0xd2000000-0xd2003fff,0xd2007000-0xd20077ff irq 23 at device 4.2 on pci3
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channel is 4.
fwohci0: EUI64 00:0a:e4:04:18:10:38:62
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:0a:e4:10:38:62
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
pci3: <mass storage> at device 4.3 (no driver attached)
rl0: <RealTek 8139 10/100BaseTX> port 0x3000-0x30ff mem
0xd2007800-0xd20078ff irq 19 at device 5.0 on pci3
rl0: Ethernet address: 00:0a:e4:55:3b:8f
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci3: <network> at device 6.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH5 UDMA100 controller> port
0x2060-0x206f,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pci0: <multimedia, audio> at device 31.5 (no driver attached)
pci0: <simple comms> at device 31.6 (no driver attached)
orm0: <Option ROM> at iomem 0xdc000-0xdffff on isa0
pmtimer0 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0c02> can't assign resources (memory)
unknown: <PNP0f13> can't assign resources (irq)
unknown: <PNP0501> can't assign resources (port)
fdc1: cannot reserve I/O port range (1 ports)
unknown: <HWPc224> can't assign resources (port)
Timecounter "TSC" frequency 3059216092 Hz quality 800
Timecounters tick every 10.000 msec
GEOM: create disk ad0 dp=0xc4608560
ad0: 76319MB <IC25N080ATMR04-0> [155061/16/63] at ata0-master UDMA100
acd0: DVDR <HL-DT-ST DVD-RW GWA-4040N> at ata1-master PIO4
Mounting root from ufs:/dev/ad0s3a
ums0: at uhub0 port 2 (addr 2) disconnected
ums0: detached
swap_pager_getswapspace(1): failed
pid 89757 (conftest), uid 0: exited on signal 12 (core dumped)
medion#

_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"