Re: ath card problem

"kalin mintchev" <[email protected]>
Newsgroups gmane.os.freebsd.devel.mobile,gmane.linux.drivers.madwifi.user
Message-ID <[email protected]>
now this is what i do:
both cards come up;
i turn xl0 down - if i don't and try to associate ath0 i get:
ifconfig: ioctl (SIOCAIFADDR): File exists ;
with the xl0 down i do:
ifconfig ath0 inet 192.168.1.21 netmask 255.255.255.0 ssid apname; ping to
192.168.1.1 works;
ping to anywhere outside does NOT work i get:
ping: sendto: Network is down
!?!?
i don't know why..

then i bring the xl0 up ping outside works fine with it.

help?!


> some additional information from the log
>  kernel: arp: 192.168.1.3 is on ath0 but got reply from
00:0b:5f:32:72:48
> on xl0
> Jul 24 18:39:50 host kernel: ath0: hardware error; resetting
> Jul 24 18:39:50 host kernel: ath0: ath_reset: unable to reset hardware;
hal status 3
> Jul 24 18:39:53 host kernel: arp: 192.168.1.3 is on ath0 but got reply
from 00:0b:5f:32:72:48 on xl0
> Jul 24 18:40:23 host last message repeated 4 times
> Jul 24 18:42:23 host last message repeated 17 times
> output from arp -a returns only:
> ? (192.168.1.1) at 00:0f:66:8b:60:13 on xl0 [ethernet]
> and arp -i ath0 -a returns nothing
> both cards have the same irq 11 at boot. i took 11 out of the
pccard.conf
> but it still comes up as 11
> can anybody help please...
> thanks
> more:
> about xl0 from dmesg:
> xl0: <3Com 3c556B Fast Etherlink XL> port 0x1800-0x18ff mem
> 0xe8101000-0xe810107f,0xe8101400-0xe810147f irq 11 at device 3.0 on pci0
xl0: chip is in D3 power mode -- setting to D0
> xl0: Ethernet address: 00:00:86:43:54:46
> miibus0: <MII bus> on xl0
> about ath0 from dmesg:
> ath0: <Atheros 5212> mem 0x88000000-0x8800ffff irq 11 at device 0.0 on
cardbus0
> ath0: mac 5.6 phy 4.1 5ghz radio 1.7 2ghz radio 2.3
> ath0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
> ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps
24Mbps 36Mbps 48Mbps 54Mbps
> ath0: turbo rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: 802.11 address: 00:80:c8:16:eb:4b
>> hi all..
>> i'm having trouble getting an ath card to work properly
>> ifconfig output:
>> ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>> 	inet6 fe80::280:c8ff:fe16:eb4b%ath0 prefixlen 64 scopeid 0x4
>> 	ether 00:80:c8:16:eb:4b
>> 	media: IEEE 802.11 Wireless Ethernet autoselect (DS/11Mbps)
>> 	status: associated
>> 	ssid accesspoint 1:accesspoint
>> 	channel 6 authmode OPEN powersavemode OFF powersavesleep 100
>> 	wepmode OFF weptxkey 1
>> output of wicontrol:
>> C serial number:			[  ]
>> Station name:				[ myhost ]
>> SSID for IBSS creation:			[ accesspoint ]
>> Current netname (SSID):			[ accesspoint ]
>> Desired netname (SSID):			[ accesspoint ]
>> Current BSSID:				[ 00:0f:66:8b:60:13 ]
>> Channel list:				[ ffe 0 1510 1515 1 0 0 0 0 2320 23 ]
>> IBSS channel:				[ 6 ]
>> Current channel:			[ 6 ]
>> Comms quality/signal/noise:		[ 0 32 0 ]
>> Promiscuous mode:			[ Off ]
>> Intersil-Prism2 based card:		[ 1 ]
>> Port type (1=BSS, 3=ad-hoc):		[ 1 ]
>> MAC address:				[ 00:80:c8:16:eb:4b ]
>> TX rate (selection):			[ 0 ]
>> TX rate (actual speed):			[ 11 ]
>> RTS/CTS handshake threshold:		[ 2312 ]
>> Create IBSS:				[ Off ]
>> Access point density:			[ 1 ]
>> Power Mgmt (1=on, 0=off):		[ 0 ]
>> Max sleep time:				[ 100 ]
>> WEP encryption:				[ Off ]
>> TX encryption key:			[ 1 ]
>> Encryption keys:			[  ][  ][  ][  ]
>> it dies see the router because it has status: associated and the
channel
>> setting is the one off the accesspoint.
>> when i turn the nic off and try to ping out i get:
>> ping: sendto: Network is down.
>> network is not down because if i turn the nic on again i can do the ping.
>> the router is common syslink one and the wireless setup is the
>> basic/default one with no wep yet.
>> i should say that the card was able to ping th router when the nic card
didn't come up - that happens sometimes on this machine - t20 thinkpad.
freebsd 5.2.1
>> is it an irq thing between the two cards?
>> what else needs to be done in order to get the card working?
>> thanks...
>> _______________________________________________
>> [email protected] mailing list
>> http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
>> To unsubscribe, send any mail to
>> "[email protected]"
> _______________________________________________
> [email protected] mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
> To unsubscribe, send any mail to
"[email protected]"


--
Software is like sex: It's better when it's free. (Linus Torvalds)



_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.