Re: DLink DWL-G650 (h/w ver. B4)

i got mine working finally (kinda) - it's a dwl-ag650 but the chip is
probably the same. check this postings. there is a script there that it
might be helpful to you.
http://www.freebsdforums.com/forums/showthread.php?s=&threadid=23880



> Hi,
>
> Thanks for the reply, and sorry for the delay - long weekend.  If I put
> the
> card in before bootup, it will give the first set of errors that I listed
> during boot, then will give the "bfe0 timeout" errors after it has
> finished
> the boot scripts.  So, that method doesn't work either.
>
> I haven't tried disabling my ethernet device.. though that's a good idea.
> How exactly do you do that?  I tried "kldunload bfe", where bfe is my nic
> device, however that doesn't work, since bfe is built into the kernel.  I
> tried syncing my sources and upgrading the kernel again, but something is
> broken in the sources, and the kernel doesn't compile even a GENERIC
> kernel.
>   So, is there a way to unload a *part* of the kernel module -- namely
> bfe?
>
> Thanks for the help, it would be great if I could get this working.  And
> it
> should work.... since it uses the ar5211.sys driver on the windows side,
> which means Atheros....
>
> regards,
> Mike
>
>
>>From: Geffy <[email protected]>
>>To: Michael Roberts <[email protected]>
>>Subject: Re: DLink DWL-G650 (h/w ver. B4)
>>Date: Fri, 30 Jul 2004 02:25:04 +0100
>>
>>Michael Roberts wrote:
>>>Greetings,
>>>
>>>I got DLink DWL-G650 (h/w ver. B4) pc-card recently, which is supposed
>>> to
>>>run 802.11g using the atheros drivers.  However, I've been trying to get
>>>it to work for the past three days w/o success.  Other people on this
>>> list
>>>claim to have gotten it working, so any help would be much appreciated.
>>
>>I have it working on mine, but mine is version B3 Firmware 2.36
>>
>>>
>>>My setup is:  -current (from early July) on a Dell 8600, running a
>>>Broadcom ethernet interface on bfe0, and a kernel recompiled with
>>> "device
>>>ath" and "device ath_hal".
>>>
>>>When I put the Dlink card in, i get the following:
>>>
>>>cardbus0:  Resource not specified in CIS: id=10, size=2000
>>>bfe1: < Broadcom ... > irq 11 at device 0.0 on cardbus0
>>>bfe1: BUG! Timeout waiting for bit 00000002 of register 42C to clear
>>>bfe1: MII without any PHY!
>>>device_attach: bfe1 attach returned 6
>>>cbb0: Cardbus activation failed.
>>
>>What happens if you have the card in during bootup? That seems to be the
>>only way I can get it to work properly in mine. It also doesnt like my
>> LAN
>>card operating, so I usually have to take that down prior to setting any
>> IP
>>address or anything on the ath0 card.
>>
>>>
>>>Then a few seconds later I get something like
>>>
>>>bfe0: BUG! Timeout waiting for bit 00000002 of register 42C
>>>
>>>about 6 times, and then the computer freezes.  The above line is not the
>>>exact output, since after the computer freezes, I can't copy the text
>>>(clearly..).
>>>
>>>Now, the above is strange because the card should be picked up by an
>>>atheros driver, not the bfe driver (note that bfe0 is my internal
>>> ethernet
>>>card, and the above is trying to assign the pccard to bfe1).  I've tryed
>>>putting in hw.pccard.debug=1 and cis_debug=1, however the computer
>>> freezes
>>>before I get any output from those.
>>>
>>>I've read in other posts on the lists that the "Resource not specified"
>>>line is some sort of resource management issue, but no one has specified
>>>how to fix it.  And that doesn't seem to address the other issue that
>>> the
>>>card isn't recognized by the atheros driver.
>>>
>>>So... I'm at a loss as to what to do.
>>>
>>>Any help would be much appreciated.
>>>
>>>regards,
>>>Mike
>>>
>>>_________________________________________________________________
>>>FREE pop-up blocking with the new MSN Toolbar – get it now!
>>>http://toolbar.msn.click-url.com/go/onm00200415ave/direct/01/
>>>
>>>_______________________________________________
>>>[email protected] mailing list
>>>http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
>>>To unsubscribe, send any mail to
>>> "[email protected]"
>>>
>>>
>>>
>>
>>Let me know if that helps, I am sending this directly to you because my
>>hosting providers mailserver never seems able to send to the
>> freebsd-mobile
>>mailing-list (mailserver problem my end, not the mailing list)
>>
>>Geoff
>
> _________________________________________________________________
> Express yourself instantly with MSN Messenger! Download today - it's FREE!
> http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/
>
> _______________________________________________
> [email protected] mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
> To unsubscribe, send any mail to "[email protected]"
>


-- 
Software is like sex: It's better when it's free. (Linus Torvalds)
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"