Hi.
I had some troubles on an E500 which were solved after a bios update.
That was CURRENT of some time back though. Don't know about 5.3.
grtz,
Dylan
> Hello!
>
> I'm trying to set up 5.3BETA5 on Compaq Armada E500, and I've run into
> the trouble: I cannot attach fxp0; it is on miniPCI, and OS can see it
> but cannot allocate interrupt.
>
> maybe someone can help?
>
> Here is my dmesg output:
>
> Rebooting...
> Copyright (c) 1992-2004 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD 5.3-BETA5 #0: Sun Sep 19 02:35:12 UTC 2004
> [email protected]:/usr/obj/usr/src/sys/GENERIC
> Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a0c000.
> Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0a0c1cc.
> Calibrating clock(s) ... i8254 clock: 1193259 Hz
> CLK_USE_I8254_CALIBRATION not specified - using default frequency
> Timecounter "i8254" frequency 1193182 Hz quality 0
> Calibrating TSC clock ... TSC clock: 995675479 Hz
> CPU: Intel Pentium III (995.68-MHz 686-class CPU)
> Origin = "GenuineIntel" Id = 0x68a Stepping = 10
> Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
> real memory = 268369920 (255 MB)
> Physical memory chunk(s):
> 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
> 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
> 0x0000000000c29000 - 0x000000000fb3ffff, 250703872 bytes (61207 pages)
> avail memory = 252964864 (241 MB)
> bios32: Found BIOS32 Service Directory header at 0xc00fa000
> bios32: Entry = 0xf0000 (c00f0000) Rev = 0 Len = 1
> pcibios: PCI BIOS entry at 0xf0000+0x478
> pnpbios: Found PnP BIOS data at 0xc00fbe10
> pnpbios: Entry = f0000:be3e Rev = 1.0
> pnpbios: Event flag at fbe36
> pnpbios: OEM ID 51b1110e
> Other BIOS signatures found:
> wlan: <802.11 Link Layer>
> random: <entropy source, Software, Yarrow>
> io: <I/O>
> mem: <memory>
> Pentium Pro MTRR support enabled
> null: <null device, zero device>
> npx0: [FAST]
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> acpi0: <COMPAQ RSDTBL> on motherboard
> acpi0: [MPSAFE]
> pci_open(1): mode 1 addr port (0x0cf8) is 0x80000058
> pci_open(1a): mode1res=0x80000000 (0x80000000)
> pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086)
> pcibios: BIOS version 2.10
> acpi_bus_number: root bus has no _BBN, assuming 0
> AcpiOsDerivePciId: bus 0 dev 0 func 0
> acpi_bus_number: root bus has no _BBN, assuming 0
> AcpiOsDerivePciId: bus 0 dev 4 func 0
> acpi_bus_number: root bus has no _BBN, assuming 0
> AcpiOsDerivePciId: bus 0 dev 4 func 1
> acpi_bus_number: root bus has no _BBN, assuming 0
> AcpiOsDerivePciId: bus 0 dev 7 func 0
> acpi0: Power Button (fixed)
> atpic: Programming IRQ9 as level/low
> ACPI timer looks BAD min = 2, max = 7, width = 5
> ACPI timer looks BAD min = 2, max = 6, width = 4
> ACPI timer looks BAD min = 2, max = 6, width = 4
> ACPI timer looks BAD min = 2, max = 7, width = 5
> ACPI timer looks BAD min = 2, max = 6, width = 4
> ACPI timer looks BAD min = 2, max = 7, width = 5
> ACPI timer looks BAD min = 2, max = 6, width = 4
> ACPI timer looks BAD min = 2, max = 7, width = 5
> ACPI timer looks BAD min = 2, max = 6, width = 4
> ACPI timer looks BAD min = 2, max = 6, width = 4
> Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x5008-0x500b on acpi0
> cpu0: <ACPI CPU (2 Cx states)> on acpi0
> acpi_tz0: <Thermal Zone> on acpi0
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> acpi link get: empty IRQ resource
> ACPI PCI link initial configuration:
> \\_SB_.C142 irq 0: [11] 11+ low,level,sharable 0.1.0
> \\_SB_.C142 irq 0: [11] 11+ low,level,sharable 0.4.0
> \\_SB_.C142 irq 0: [11] 11+ low,level,sharable 0.4.1
> \\_SB_.C14A irq 0: [11] 11+ low,level,sharable 0.7.3
> \\_SB_.C149 irq 0: [11] 11+ low,level,sharable 0.8.0
> \\_SB_.C149 irq 0: [11] 11+ low,level,sharable 0.9.0
> \\_SB_.C14A irq 0: [11] 11+ low,level,sharable 0.9.1
> \\_SB_.C142 irq 0: [11] 11+ low,level,sharable 0.16.0
> \\_SB_.C148 irq 0: [11] 0+ low,level,sharable 0.16.1
> \\_SB_.C149 irq 0: [11] 11+ low,level,sharable 0.16.2
> \\_SB_.C14A irq 0: [11] 11+ low,level,sharable 0.16.3
> pci0: <ACPI PCI bus> on pcib0
> pci0: physical bus=0
> map[10]: type 3, range 32, base 50000000, size 26, enabled
> found-> vendor=0x8086, dev=0x7190, revid=0x03
> bus=0, slot=0, func=0
> class=06-00-00, hdrtype=0x00, mfdev=0
> cmdreg=0x0006, statreg=0xa210, cachelnsz=0 (dwords)
> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> found-> vendor=0x8086, dev=0x7191, revid=0x03
> bus=0, slot=1, func=0
> class=06-04-00, hdrtype=0x01, mfdev=0
> cmdreg=0x0003, statreg=0x0220, cachelnsz=0 (dwords)
> lattimer=0x40 (1920 ns), mingnt=0x8c (35000 ns), maxlat=0x00 (0 ns)
> map[10]: type 1, range 32, base 41100000, size 12, enabled
> pcib0: matched entry for 0.4.INTA (src \\_SB_.C142)
> pcib0: possible interrupts: 11
> ACPI PCI link arbitrated settings:
> \\_SB_.C142 (references 4, priority 440):
> interrupts: 11
> penalty: 110
> \\_SB_.C14A (references 3, priority 330):
> interrupts: 11
> penalty: 110
> \\_SB_.C149 (references 3, priority 330):
> interrupts: 11
> penalty: 110
> \\_SB_.C148 (references 1, priority 110):
> interrupts: 11
> penalty: 110
> pcib0: slot 4 INTA routed to irq 11 via \\_SB_.C142
> found-> vendor=0x104c, dev=0xac1c, revid=0x01
> bus=0, slot=4, func=0
> class=06-07-00, hdrtype=0x02, mfdev=1
> cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
> lattimer=0x42 (1980 ns), mingnt=0xc4 (49000 ns), maxlat=0x03 (750 ns)
> intpin=a, irq=11
> powerspec 1 supports D0 D1 D2 D3 current D0
> map[10]: type 1, range 32, base 41180000, size 12, enabled
> pcib0: matched entry for 0.4.INTA (src \\_SB_.C142)
> pcib0: slot 4 INTA is already routed to irq 11
> found-> vendor=0x104c, dev=0xac1c, revid=0x01
> bus=0, slot=4, func=1
> class=06-07-00, hdrtype=0x02, mfdev=1
> cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
> lattimer=0x42 (1980 ns), mingnt=0xc4 (49000 ns), maxlat=0x03 (750 ns)
> intpin=a, irq=11
> powerspec 1 supports D0 D1 D2 D3 current D0
> found-> vendor=0x8086, dev=0x7110, revid=0x02
> bus=0, slot=7, func=0
> class=06-80-00, hdrtype=0x00, mfdev=1
> cmdreg=0x010f, statreg=0x0280, cachelnsz=0 (dwords)
> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> map[20]: type 4, range 32, base 00004010, size 4, enabled
> found-> vendor=0x8086, dev=0x7111, revid=0x01
> bus=0, slot=7, func=1
> class=01-01-80, hdrtype=0x00, mfdev=0
> cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> map[20]: type 4, range 32, base 00004020, size 5, enabled
> pcib0: matched entry for 0.7.INTD (src \\_SB_.C14A)
> pcib0: possible interrupts: 11
> ACPI PCI link arbitrated settings:
> \\_SB_.C14A (references 3, priority 780):
> interrupts: 11
> penalty: 260
> \\_SB_.C149 (references 3, priority 780):
> interrupts: 11
> penalty: 260
> \\_SB_.C148 (references 1, priority 260):
> interrupts: 11
> penalty: 260
> pcib0: slot 7 INTD routed to irq 11 via \\_SB_.C14A
> found-> vendor=0x8086, dev=0x7112, revid=0x01
> bus=0, slot=7, func=2
> class=0c-03-00, hdrtype=0x00, mfdev=0
> cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> intpin=d, irq=11
> map[90]: type 4, range 32, base 00004000, size 4, enabled
> found-> vendor=0x8086, dev=0x7113, revid=0x03
> bus=0, slot=7, func=3
> class=06-80-00, hdrtype=0x00, mfdev=0
> cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords)
> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> map[10]: type 4, range 32, base 00004400, size 8, enabled
> pcib0: matched entry for 0.8.INTA (src \\_SB_.C149)
> pcib0: possible interrupts: 11
> ACPI PCI link arbitrated settings:
> \\_SB_.C149 (references 3, priority 1200):
> interrupts: 11
> penalty: 400
> \\_SB_.C148 (references 1, priority 400):
> interrupts: 11
> penalty: 400
> pcib0: slot 8 INTA routed to irq 11 via \\_SB_.C149
> found-> vendor=0x125d, dev=0x1978, revid=0x10
> bus=0, slot=8, func=0
> class=04-01-00, hdrtype=0x00, mfdev=0
> cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
> lattimer=0x40 (1920 ns), mingnt=0x02 (500 ns), maxlat=0x18 (6000 ns)
> intpin=a, irq=11
> powerspec 2 supports D0 D1 D2 D3 current D0
> found-> vendor=0x8086, dev=0x1229, revid=0xff
> bus=0, slot=9, func=0
> class=02-ff-ff, hdrtype=0x7f, mfdev=1
> cmdreg=0x0000, statreg=0x8290, cachelnsz=255 (dwords)
> lattimer=0xff (7650 ns), mingnt=0xff (63750 ns), maxlat=0xff (63750 ns)
> intpin=_, irq=255
> found-> vendor=0x8086, dev=0x124b, revid=0x01
> bus=0, slot=12, func=0
> class=06-04-80, hdrtype=0x01, mfdev=0
> cmdreg=0x0087, statreg=0x0400, cachelnsz=8 (dwords)
> lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
> agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0x50000000-
> 0x53ffffff at device 0.0 on pci0
> agp0: Reserved 0x4000000 bytes for rid 0x10 type 3 at 0x50000000
> agp0: allocating GATT for aperture of size 64M
> pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
> pcib1: secondary bus 1
> pcib1: subordinate bus 1
> pcib1: I/O decode 0x3000-0x3fff
> pcib1: memory decode 0x40000000-0x410fffff
> pcib1: prefetched decode 0xfff00000-0xfffff
> pcib1: could not get PCI interrupt routing table for \\_SB_.C005.C012 -
> AE_NOT_FOUND
> pci1: <ACPI PCI bus> on pcib1
> pci1: physical bus=1
> map[10]: type 1, range 32, base 40000000, size 24, enabled
> pcib1: device (null) requested decoded memory range 0x40000000-
> 0x40ffffff
> map[14]: type 4, range 32, base 00003000, size 8, enabled
> pcib1: device (null) requested decoded I/O range 0x3000-0x30ff
> map[18]: type 1, range 32, base 41000000, size 12, enabled
> pcib1: device (null) requested decoded memory range 0x41000000-
> 0x41000fff
> pcib0: matched entry for 0.1.INTA (src \\_SB_.C142)
> pcib0: slot 1 INTA is already routed to irq 11
> pcib1: slot 0 INTA is routed to irq 11
> found-> vendor=0x1002, dev=0x4c4d, revid=0x64
> bus=1, slot=0, func=0
> class=03-00-00, hdrtype=0x00, mfdev=0
> cmdreg=0x0087, statreg=0x0290, cachelnsz=8 (dwords)
> lattimer=0x42 (1980 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
> intpin=a, irq=11
> powerspec 1 supports D0 D1 D2 D3 current D0
> pci1: <display, VGA> at device 0.0 (no driver attached)
> cbb0: <TI1225 PCI-CardBus Bridge> mem 0x41100000-0x41100fff irq 11 at
> device 4.0 on pci0
> cbb0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0x41100000
> cardbus0: <CardBus bus> on cbb0
> pccard0: <16-bit PCCard bus> on cbb0
> cbb0: [MPSAFE]
> cbb0: PCI Configuration space:
> 0x00: 0xac1c104c 0x02100007 0x06070001 0x00824208
> 0x10: 0x41100000 0x020000a0 0x20020200 0xfffff000
> 0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc
> 0x30: 0x00000000 0xfffffffc 0x00000000 0x0744010b
> 0x40: 0xb1210e11 0x00000001 0x00000000 0x00000000
> 0x50: 0x00000000 0x00000000 0x00000000 0x00000000
> 0x60: 0x00000000 0x00000000 0x00000000 0x00000000
> 0x70: 0x00000000 0x00000000 0x00000000 0x00000000
> 0x80: 0x28049060 0x00000000 0x00000000 0x01001c72
> 0x90: 0x60642280 0x00000000 0x00000000 0x00000000
> 0xa0: 0x7e210001 0x00800000 0x00000801 0x0000001f
> 0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
> 0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
> 0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
> 0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
> 0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
> cbb1: <TI1225 PCI-CardBus Bridge> mem 0x41180000-0x41180fff irq 11 at
> device 4.1 on pci0
> cbb1: Reserved 0x1000 bytes for rid 0x10 type 3 at 0x41180000
> cardbus1: <CardBus bus> on cbb1
> pccard1: <16-bit PCCard bus> on cbb1
> cbb1: [MPSAFE]
> cbb1: PCI Configuration space:
> 0x00: 0xac1c104c 0x02100007 0x06070001 0x00824208
> 0x10: 0x41180000 0x020000a0 0x20030300 0xfffff000
> 0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc
> 0x30: 0x00000000 0xfffffffc 0x00000000 0x0744010b
> 0x40: 0xb1210e11 0x00000001 0x00000000 0x00000000
> 0x50: 0x00000000 0x00000000 0x00000000 0x00000000
> 0x60: 0x00000000 0x00000000 0x00000000 0x00000000
> 0x70: 0x00000000 0x00000000 0x00000000 0x00000000
> 0x80: 0x28449060 0x00000000 0x00000000 0x01001c72
> 0x90: 0x60642280 0x00000000 0x00000000 0x00000000
> 0xa0: 0x7e210001 0x00800000 0x00000801 0x0000001f
> 0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
> 0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
> 0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
> 0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
> 0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
> PCI-ISA bridge with incorrect subclass 0x80
> PCI-ISA bridge with incorrect subclass 0x80
> isab0: <PCI-ISA bridge> at device 7.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel PIIX4 UDMA33 controller> port 0x4010-0x401f,0x376,0x170-
> 0x177,0x3f6,0x1f0-0x1f7 at device 7.1 on pci0
> atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x4010
> ata0: channel #0 on atapci0
> atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
> atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
> ata0: reset tp1 mask=03 ostat0=50 ostat1=50
> ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
> ata0-slave: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
> ata0: reset tp2 stat0=50 stat1=00 devices=0x9<ATAPI_SLAVE,ATA_MASTER>
> ata0: [MPSAFE]
> ata1: channel #1 on atapci0
> atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
> atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
> ata1: reset tp1 mask=00 ostat0=ff ostat1=ff
> ata1: [MPSAFE]
> uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x4020-0x403f irq
> 11 at device 7.2 on pci0
> uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0x4020
> uhci0: [GIANT-LOCKED]
> usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
> usb0: USB revision 1.0
> uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> uhub1: Atmel UHB124 hub, class 9/0, rev 1.00/1.00, addr 2
> uhub1: 4 ports with 4 removable, self powered
> umass0: AOPEN Aopen USB2.0 Device, rev 2.00/0.01, addr 3
> umass0: Get Max Lun not supported (STALLED)
> umass0:0:0:-1: Attached to scbus0
> umass1: USB Flash Disk, rev 2.00/2.00, addr 4
> umass1:1:1:-1: Attached to scbus1
> pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
> pci0: <multimedia, audio> at device 8.0 (no driver attached)
> fxp0: <Intel 82557/8/9 Pro/100 Ethernet> at device 9.0 on pci0
> fxp0: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0x80000000
> fxp0: using memory space register mapping
> pcib0: no PRT entry for 0.9.INT?
> fxp0: could not map interrupt
> device_attach: fxp0 attach returned 6
> pcib2: <ACPI PCI-PCI bridge> at device 12.0 on pci0
> pcib2: secondary bus 4
> pcib2: subordinate bus 4
> pcib2: I/O decode 0x0-0xfff
> pcib2: memory decode 0x0-0xfffff
> pcib2: prefetched decode 0xfff00000-0xfffff
> pcib2: Subtractively decoded bridge.
> ACPI PCI link initial configuration:
> \\_SB_.C142 irq*11: [11] 11+ low,level,sharable 4.7.0
> \\_SB_.C142 irq*11: [11] 11+ low,level,sharable 4.8.0
> \\_SB_.C148 irq 0: [11] 0+ low,level,sharable 4.8.1
> \\_SB_.C149 irq*11: [11] 11+ low,level,sharable 4.8.2
> \\_SB_.C14A irq*11: [11] 11+ low,level,sharable 4.8.3
> \\_SB_.C148 irq 0: [11] 0+ low,level,sharable 4.9.0
> \\_SB_.C149 irq*11: [11] 11+ low,level,sharable 4.9.1
> \\_SB_.C14A irq*11: [11] 11+ low,level,sharable 4.9.2
> \\_SB_.C142 irq*11: [11] 11+ low,level,sharable 4.9.3
> \\_SB_.C149 irq*11: [11] 11+ low,level,sharable 4.10.0
> \\_SB_.C14A irq*11: [11] 11+ low,level,sharable 4.10.1
> \\_SB_.C142 irq*11: [11] 11+ low,level,sharable 4.10.2
> \\_SB_.C148 irq 0: [11] 0+ low,level,sharable 4.10.3
> pci4: <ACPI PCI bus> on pcib2
> pci4: physical bus=4
> map[10]: type 4, range 32, base 000001e0, size 3, enabled
> map[14]: type 4, range 32, base 000003e4, size 2, enabled
> map[18]: type 4, range 32, base 00000160, size 3, enabled
> map[1c]: type 4, range 32, base 00000364, size 2, enabled
> map[20]: type 4, range 32, base 00000190, size 4, enabled
> pcib2: matched entry for 4.7.INTA (src \\_SB_.C142)
> pcib2: slot 7 INTA is already routed to irq 11
> found-> vendor=0x1095, dev=0x0646, revid=0x07
> bus=4, slot=7, func=0
> class=01-01-8f, hdrtype=0x00, mfdev=0
> cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
> lattimer=0x40 (1920 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns)
> intpin=a, irq=11
> powerspec 1 supports D0 D1 D2 D3 current D0
> atapci1: <CMD 646U2 UDMA33 controller> port 0x190-0x19f,0x364-
> 0x367,0x160-0x167,0x3e4-0x3e7,0x1e0-0x1e7 irq 11 at device 7.0 on pci4
> atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0x190
> atapci1: [MPSAFE]
> ata2: channel #0 on atapci1
> atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1e0
> atapci1: Reserved 0x4 bytes for rid 0x14 type 4 at 0x3e4
> ata2: reset tp1 mask=00 ostat0=ff ostat1=ff
> ata2: [MPSAFE]
> ata3: channel #1 on atapci1
> atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0x160
> atapci1: Reserved 0x4 bytes for rid 0x1c type 4 at 0x364
> ata3: reset tp1 mask=00 ostat0=ff ostat1=ff
> ata3: [MPSAFE]
> acpi_button0: <Sleep Button> on acpi0
> acpi_acad0: <AC Adapter> on acpi0
> acpi_cmbat0: <Control Method Battery> on acpi0
> acpi_cmbat1: <Control Method Battery> on acpi0
> acpi_cmbat2: <Control Method Battery> on acpi0
> acpi_cmbat3: <Control Method Battery> on acpi0
> acpi_lid0: <Control Method Lid Switch> on acpi0
> unknown: not probed (disabled)
> atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> atkbd: the current kbd controller command byte 0065
> atkbd: keyboard ID 0x41ab (2)
> kbd0 at atkbd0
> kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
> atkbd0: [GIANT-LOCKED]
> psm0: unable to allocate IRQ
> psmcpnp0 irq 12 on acpi0
> psm0: current command byte:0065
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> psm0: [GIANT-LOCKED]
> psm0: model Synaptics Touchpad, device ID 0-00, 3 buttons
> psm0: config:00000000, flags:00000008, packet size:6
> psm0: syncmask:c0, syncbits:00
> sio0: irq maps: 0x1 0x11 0x1 0x1
> sio0 port 0x3f8-0x3ff irq 4 on acpi0
> sio0: type 16550A
> fdc0: <floppy drive controller (FDE)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2
> on acpi0
> fdc0: ic_type 90 part_id 80
> fdc0: [MPSAFE]
> fdc0: [FAST]
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> sio1: irq maps: 0x1 0x9 0x1 0x1
> sio1 port 0x100-0x107,0x3e8-0x3ef irq 3 drq 5 on acpi0
> sio1: type 16550A
> ppc0: using extended I/O port range
> ppc0: EPP SPP
> ppc0 port 0x778-0x77a,0x378-0x37f irq 7 drq 3 on acpi0
> ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
> ppbus0: <Parallel port bus> on ppc0
> plip0: <PLIP network interface> on ppbus0
> plip0: bpf attached
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> unknown: not probed (disabled)
> unknown: not probed (disabled)
> unknown: not probed (disabled)
> ata: ata0 already exists; skipping it
> ata: ata1 already exists; skipping it
> atkbdc: atkbdc0 already exists; skipping it
> fdc: fdc0 already exists; skipping it
> ppc: ppc0 already exists; skipping it
> sio: sio0 already exists; skipping it
> sio: sio1 already exists; skipping it
> Trying Read_Port at 203
> Trying Read_Port at 243
> Trying Read_Port at 283
> Trying Read_Port at 2c3
> Trying Read_Port at 303
> Trying Read_Port at 343
> Trying Read_Port at 383
> Trying Read_Port at 3c3
> ex_isa_identify()
> unknown: status reg test failed ff
> unknown: status reg test failed ff
> unknown: status reg test failed ff
> unknown: status reg test failed ff
> unknown: status reg test failed ff
> unknown: status reg test failed ff
> sc: sc0 already exists; skipping it
> vga: vga0 already exists; skipping it
> isa_probe_children: disabling PnP devices
> isa_probe_children: probing non-PnP devices
> orm0: <ISA Option ROM> at iomem 0xc0000-0xcffff on isa0
> pmtimer0 on isa0
> adv0: not probed (disabled)
> aha0: not probed (disabled)
> aic0: not probed (disabled)
> bt0: not probed (disabled)
> cs0: not probed (disabled)
> ed0: not probed (disabled)
> fe0: not probed (disabled)
> ie0: not probed (disabled)
> lnc0: not probed (disabled)
> pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
> pcic1: not probed (disabled)
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
> sio2: not probed (disabled)
> sio3: not probed (disabled)
> sn0: not probed (disabled)
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
> isa0
> fb0: vga0, vga, type:VGA (5), flags:0x7007f
> fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
> fb0: init mode:24, bios mode:3, current mode:24
> fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
> vga0: vga: WARNING: video mode switching is not fully supported on this
> adapter
> VGA parameters upon power-up
> 50 18 10 00 00 00 03 00 02 67 6f 4f 4f 93 55 83
> 9e 1f 00 4f 0d 0e 00 00 07 80 8f 82 8f 28 1f 8f
> 9f a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
> 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
> VGA parameters in BIOS for mode 24
> 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
> bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
> b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
> 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
> EGA/VGA parameters to be used for mode 24
> 50 18 10 00 00 00 03 00 02 67 6f 4f 4f 93 55 83
> 9e 1f 00 4f 0d 0e 00 00 07 80 8f 82 8f 28 1f 8f
> 9f a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
> 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
> vt0: not probed (disabled)
> isa_probe_children: probing PnP devices
> Device configuration finished.
> procfs registered
> Timecounter "TSC" frequency 995675479 Hz quality 800
> Timecounters tick every 10.000 msec
> lo0: bpf attached
> cpu0: set speed to 100.0%
> acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
> acpi_acad0: acline initialization start
> acpi_acad0: On Line
> acpi_acad0: acline initialization done, tried 1 times
> acpi_cmbat0: battery initialization start
> acpi_cmbat0: battery initialization done, tried 1 times
> acpi_cmbat1: battery initialization start
> acpi_cmbat2: battery initialization start
> acpi_cmbat3: battery initialization start
> acpi_tz0: _AC2: temperature 65.0 >= setpoint 50.0
> acpi_tz0: _AC1: temperature 65.0 >= setpoint 65.0
> acpi_tz0: switched from _AC0 to _AC1: 65.0C
> acpi_tz0: _AC2: temperature 65.0 >= setpoint 50.0
> acpi_tz0: _AC2: temperature 65.0 >= setpoint 50.0
> acpi_tz0: switched from _AC1 to _AC2: 65.0C
> fdc0: output ready timeout
> fdc0: output ready timeout
> fdc0: output ready timeout
> fdc0: output ready timeout
> fdc0: output ready timeout
> fdc0: output ready timeout
> fdc0: output ready timeout
> ata0-slave: pio=0x0c wdma=0x22 udma=0xffffffff cable=40pin
> ATAPI_RESET time = 5380us
> ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=40pin
> ata0-master: setting PIO4 on Intel PIIX4 chip
> ata0-master: setting UDMA33 on Intel PIIX4 chip
> ata0-slave: setting PIO4 on Intel PIIX4 chip
> ad0: <SAMSUNG MP0402H/UC100-11> ATA-7 disk at ata0-master
> ad0: 38204MB (78242976 sectors), 77622 C, 16 H, 63 S, 512 B
> ad0: 16 secs/int, 1 depth queue, UDMA33
> ar: FreeBSD check1 failed
> acd0: <CD-224E/9.0B> CDROM drive at ata0 as slave
> acd0: read 4134KB/s (4134KB/s), 512KB buffer, PIO4
> acd0: Reads: CDR, CDDA stream
> acd0: Writes:
> acd0: Audio: play, 256 volume levels
> acd0: Mechanism: ejectable tray, unlocked
> acd0: Medium: no/blank disc
> fdc0: output ready timeout
> fdc0: input ready timeout
> fdc0: input ready timeout
> fdc0: output ready timeout
> fdc0: input ready timeout
> fdc0: input ready timeout
> fdc0: output ready timeout
> fdc0: input ready timeout
> fdc0: input ready timeout
> fdc0: output ready timeout
> fdc0: input ready timeout
> fdc0: input ready timeout
> GEOM: new disk ad0
> [0] f:00 typ:11 s(CHS):95/16/1 e(CHS):961/224/63 s:1527183 l:13925457
> [1] f:80 typ:165 s(CHS):0/1/1 e(CHS):94/254/63 s:63 l:1526112
> [2] f:00 typ:165 s(CHS):961/225/1 e(CHS):1023/254/63 s:15452640
> l:62783910
> [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
> GEOM: Configure ad0s1, start 781917696 length 7129833984 end 7911751679
> GEOM: Configure ad0s2, start 32256 length 781369344 end 781401599
> GEOM: Configure ad0s3, start 7911751680 length 32145361920 end
> 40057113599
> GEOM: Configure ad0s2a, start 0 length 781369344 end 781369343
> GEOM: Configure ad0s2c, start 0 length 781369344 end 781369343
> GEOM: Configure ad0s3b, start 0 length 1073741824 end 1073741823
> GEOM: Configure ad0s3c, start 0 length 32145361920 end 32145361919
> GEOM: Configure ad0s3d, start 1073741824 length 4294967296 end
> 5368709119
> GEOM: Configure ad0s3e, start 5368709120 length 4294967296 end
> 9663676415
> GEOM: Configure ad0s3f, start 9663676416 length 22481685504 end
> 32145361919
> (probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR
> (probe0:umass-sim0:0:0:0): Retrying Command
> (probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR
> (probe0:umass-sim0:0:0:0): Retrying Command
> (probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR
> (probe0:umass-sim0:0:0:0): Retrying Command
> (probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR
> (probe0:umass-sim0:0:0:0): Retrying Command
> (probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR
> (probe0:umass-sim0:0:0:0): error 5
> (probe0:umass-sim0:0:0:0): Retries Exausted
> pass0 at umass-sim1 bus 1 target 0 lun 0
> pass0: <I-Stick2 IntelligentStick 2.00> Removable Direct Access SCSI-2
> device
> pass0: Serial Number \^_
> pass0: 1.000MB/s transfers
> GEOM: new disk da0
> da0 at umass-sim1 bus 1 target 0 lun 0
> da0: <I-Stick2 IntelligentStick 2.00> Removable Direct Access SCSI-2
> device
> da0: Serial Number \^_
> da0: 1.000MB/s transfers
> da0: 249MB (511488 512 byte sectors: 64H 32S/T 249C)
> [0] f:00 typ:6 s(CHS):0/1/1 e(CHS):247/63/32 s:32 l:507872
> [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
> [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
> [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
> GEOM: Configure da0s1, start 16384 length 260030464 end 260046847
> Mounting root from ufs:/dev/ad0s2a
> start_init: trying /sbin/init
>
>
> --
> Alex
> _______________________________________________
> [email protected] mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
> To unsubscribe, send any mail to "freebsd-mobile-
> [email protected]"
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"
lmpx.com only provides a reader for public news (NNTP) servers. It is not
affiliated with the servers or forums shown here and is not responsible for
the content of articles, which is written by their respective authors.