snd_neomagic kldloads, then 5.2.1-p11 freezes
Jan Stary <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.mobile |
|---|---|
| Message-ID | <20041027223248.GA67950__16972.5729189397$1098962863$gmane$org@ns.stare.cz> |
Hello,
I am running FreeBSD 5.2.1-p11 on a Dell Latitude LS notebook. (See
KERNCONF and dmesg at the end.) Nearly everything is working fine,
except for the sound chip.
I built the sound stuff as modules (sound/pcm + sound/driver/neomagic,
resulting in snd_pcm + snd_neomagic).
When I try to insert the module, I get
# kldload snd_neomagic
pcm0: <NeoMagic 256AV> mem 0xfea00000-0xfeafffff,0xf7800000-0xf7bfffff, irq 10, device 0.1 on pci1
and then the system freezes. If I compile pcm right into the kernel, the
freeze occurs during bootime with the same message.
I also have wi0 running at irq 10 (see dmesg); when I don't use it (no
card in, no device attached to wi0, irq 10 not used by anything), the
freeze ocuurs all the same.
Suspecting some conflict between devices using irq 10, I said
hint.pcm.0.irq="5" in /boot/device.hints (irq 5 is not used by
anything), but kldloading snd_neomagic still tries to use irq 10
- why is that? What is the right way of telling a device which irq to
use?
Before I even found that it is a NeoMagic, I built all the sound modules
and tried kldloading them. Some of them just loaded and nothing happened
(I probably don't have any device they could serve), some resulted in
# kldload snd_ad1816
sio1: configured irq 3 not in bitmap of probed irqs 0x4000
sio1: port may not be enabled
# kldload snd_ess
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
# kldload snd_mss
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
# kldload speaker
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
speaker0 port0x61 on acpi0
Why does kldloading a sound module have to do anything with sio1?
Where is irq 3 'configured' to be used? (by the sound module?)
So I also disabled sio1 in device.hints (hint.sio.1.disabled="1") - there
is only one sio at the machine anyway.
I use ACPI - does it have anything to do with my problem?
(with ACPI, devices are 'on acpi0', not on 'on isa0' etc.)
Thanks
Jan
This is my KERNCONF:
# DELL -- kernel configuration file for FreeBSD/i386 on Dell Latitude LS
ident DELL
machine i386
cpu I686_CPU
#options CPU_SUSP_HALT # suspend on halt
#options CPU_UPGRADE_HW_CACHE # eliminates unneeded cache flushes
#options PERFMON
#hints "GENERIC.hints" # Default places to look for devices.
#makeoptions DEBUG=-g # Build kernel with gdb(1) debug symbols
options SCHED_ULE # ULE scheduler
options INET # InterNETworking
options INET6 # IPv6 communications protocols
options IPSEC
options IPSEC_DEBUG
options BRIDGE
options FFS # Berkeley Fast Filesystem
options SOFTUPDATES # Enable FFS soft updates support
options UFS_ACL # Support for access control lists
options UFS_DIRHASH # Improve performance on big directories
options MD_ROOT # MD is a potential root device
options PROCFS # Process filesystem (requires PSEUDOFS)
options PSEUDOFS # Pseudo-filesystem framework
options GEOM_GPT # GUID Partition Tables.
options COMPAT_43 # Compatible with BSD 4.3 [KEEP THIS!]
options COMPAT_FREEBSD4 # Compatible with FreeBSD4
#options SCSI_DELAY=15000 # Delay (in ms) before probing SCSI
options KTRACE # ktrace(1) support
options SYSVSHM # SYSV-style shared memory
options SYSVMSG # SYSV-style message queues
options SYSVSEM # SYSV-style semaphores
options _KPOSIX_PRIORITY_SCHEDULING # POSIX P1003_1B real-time extensions
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
# Bus support. Do not remove isa, even if you have no isa slots
device isa
device eisa
device pci
# Floppy drives
#device fdc
# ATA and ATAPI devices
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
options ATA_STATIC_ID # Static device numbering
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc # AT keyboard controller
device atkbd # AT keyboard
device psm # PS/2 mouse
device vga # VGA video card driver
device agp # support several AGP chipsets
#options VESA
device splash # Splash screen and screen saver support
device sc # syscons: the default console driver
# Floating point support - do not disable.
device npx
# Add suspend/resume support for the i8254.
device pmtimer
# PCCARD (PCMCIA) support
# PCMCIA and cardbus bridge support
device cbb # cardbus (yenta) bridge
device pccard # PC Card (16-bit) bus
device cardbus # CardBus (32-bit) bus
# Serial (COM) ports
device sio # 8250, 16[45]50 based serial ports
# Parallel port
device ppc
device ppbus # Parallel port bus (required)
#device lpt # Printer
#device plip # TCP/IP over parallel
#device ppi # Parallel port interface device
# ethernet
device miibus # MII bus support
device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
# Wireless NIC cards
device wlan # 802.11 support
device wi # WaveLAN/Intersil/Symbol 802.11 wireless NICs.
# Pseudo devices.
device loop # Network loopback
#device mem # Memory and kernel memory devices
#device io # I/O device
device random # Entropy device
device ether # Ethernet support
#device sl # Kernel SLIP
#device ppp # Kernel PPP
device tun # Packet tunnel.
device pty # Pseudo-ttys (telnet etc)
device md # Memory "disks"
#device gif # IPv6 and IPv4 tunneling
#device faith # IPv6-to-IPv4 relaying (translation)
# The `bpf' device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
device bpf # Berkeley packet filter
# ipfw
options IPFIREWALL
options IPFIREWALL_VERBOSE
options IPDIVERT
options IPSTEALTH
This is my dmesg:
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.2.1-RELEASE-p11 #4: Sun Oct 24 15:28:38 CEST 2004
root@dell:/usr/obj/usr/src/sys/DELL
Preloaded elf kernel "/boot/kernel/kernel" at 0xc07ad000.
Preloaded elf module "/boot/kernel/splash_bmp.ko" at 0xc07ad1f4.
Preloaded elf module "/boot/kernel/vesa.ko" at 0xc07ad2a4.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc07ad350.
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel Pentium III (398.27-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x683 Stepping = 3
Features=0x387f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,PN,MMX,FXSR,SSE>
real memory = 134152192 (127 MB)
avail memory = 124870656 (119 MB)
Pentium Pro MTRR support enabled
VESA: v2.0, 2496k memory, flags:0x0, mode table:0xc0758c62 (1000022)
VESA: MagicGraph 256 AV 48K
module_register_init: MOD_LOAD (splash_bmp, 0xc0750810, 0) error 2
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <PTLTD RSDT > on motherboard
pcibios: BIOS version 2.10
Using $PIR table, 7 entries at 0xc00fdf50
ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
acpi0: Power Button (fixed)
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib0: slot 7 INTD is routed to irq 10
pcib0: slot 10 INTA is routed to irq 10
pcib0: slot 13 INTA is routed to irq 10
pcib0: slot 16 INTA is routed to irq 3
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0xf8000000-0xfbffffff at device 0.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib1: slot 0 INTA is routed to irq 10
pcib1: slot 0 INTB is routed to irq 10
pci1: <display, VGA> at device 0.0 (no driver attached)
pci1: <multimedia, audio> at device 0.1 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port 0xfcd0-0xfcdf at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
pci0: <serial bus, USB> at device 7.2 (no driver attached)
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
cbb0: <TI1211 PCI-CardBus Bridge> irq 10 at device 10.0 on pci0
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb0: [MPSAFE]
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xfc00-0xfc7f mem 0xfedfec00-0xfedfec7f irq 10 at device 13.0 on pci0
xl0: Ethernet address: 00:b0:d0:4d:ae:31
miibus0: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <simple comms> at device 16.0 (no driver attached)
acpi_acad0: <AC Adapter> on acpi0
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
ACPI-0175: *** Error: Method execution failed [\\_SB_.BAT1._STA] (Node 0xc1c33960), AE_NOT_EXIST
acpi_cmbat0: <Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
ACPI-1287: *** Error: Method execution failed [\\_SB_.LID_._PSW] (Node 0xc1c33800), AE_NOT_EXIST
acpi_button0: <Sleep Button> on acpi0
ppc0 port 0x778-0x77f,0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
acpi_ec0: <Embedded Controller: GPE 0> port 0x66,0x62 on acpi0
ACPI-0438: *** Error: Handler for [EmbeddedControl] returned AE_NO_HARDWARE_RESPONSE
ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NO_HARDWARE_RESPONSE
ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NO_HARDWARE_RESPONSE
ACPI-0438: *** Error: Handler for [EmbeddedControl] returned AE_NO_HARDWARE_RESPONSE
ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NO_HARDWARE_RESPONSE
ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NO_HARDWARE_RESPONSE
ACPI-0438: *** Error: Handler for [EmbeddedControl] returned AE_NO_HARDWARE_RESPONSE
ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NO_HARDWARE_RESPONSE
ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NO_HARDWARE_RESPONSE
ACPI-0438: *** Error: Handler for [EmbeddedControl] returned AE_NO_HARDWARE_RESPONSE
ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NO_HARDWARE_RESPONSE
ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NO_HARDWARE_RESPONSE
ACPI-0438: *** Error: Handler for [EmbeddedControl] returned AE_NO_HARDWARE_RESPONSE
ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NO_HARDWARE_RESPONSE
ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NO_HARDWARE_RESPONSE
ACPI-0438: *** Error: Handler for [EmbeddedControl] returned AE_NO_HARDWARE_RESPONSE
ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NO_HARDWARE_RESPONSE
ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NO_HARDWARE_RESPONSE
ACPI-0438: *** Error: Handler for [EmbeddedControl] returned AE_NO_HARDWARE_RESPONSE
ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NO_HARDWARE_RESPONSE
ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NO_HARDWARE_RESPONSE
ACPI-0438: *** Error: Handler for [EmbeddedControl] returned AE_NO_HARDWARE_RESPONSE
ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NO_HARDWARE_RESPONSE
ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NO_HARDWARE_RESPONSE
ACPI-0438: *** Error: Handler for [EmbeddedControl] returned AE_NO_HARDWARE_RESPONSE
ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NO_HARDWARE_RESPONSE
ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NO_HARDWARE_RESPONSE
ACPI-0438: *** Error: Handler for [EmbeddedControl] returned AE_NO_HARDWARE_RESPONSE
ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NO_HARDWARE_RESPONSE
ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NO_HARDWARE_RESPONSE
ACPI-0438: *** Error: Handler for [EmbeddedControl] returned AE_NO_HARDWARE_RESPONSE
ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NO_HARDWARE_RESPONSE
ACPI-0175: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.FDC_.FDDA._STA] (Node 0xc1c2f6e0), AE_NO_HARDWARE_RESPONSE
orm0: <Option ROMs> at iomem 0xdc000-0xdffff,0xcc000-0xcc7ff,0xc0000-0xcbfff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 398271068 Hz quality 800
Timecounters tick every 10.000 msec
ipfw2 initialized, divert enabled, rule-based forwarding enabled, default to deny, logging unlimited
IPsec: Initialized Security Association Processing.
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
wi0: < IEEE 802.11 Wireless LAN/PC Card> at port 0x100-0x13f irq 10 function 0 config 1 on pccard0
wi0: 802.11 address: 00:60:b3:78:f2:3c
wi0: using RF:PRISM2.5 MAC:ISL3873
wi0: Intersil Firmware: Primary (1.0.7), Station (1.3.6)
wi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
GEOM: create disk ad0 dp=0xc1cad860
ad0: 19077MB <IC25N020ATMR04-0> [38760/16/63] at ata0-master UDMA33
ACPI-0438: *** Error: Handler for [EmbeddedControl] returned AE_NO_HARDWARE_RESPONSE
ACPI-1287: *** Error: Method execution failed [\\_SB_.ACAD._PSR] (Node 0xc1c33b20), AE_NO_HARDWARE_RESPONSE
Mounting root from ufs:/dev/ad0s2a
system power profile changed to 'economy'
ACPI-0438: *** Error: Handler for [EmbeddedControl] returned AE_NO_HARDWARE_RESPONSE
ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.ISA_.EC0_.SMRD] (Node 0xc1c31980), AE_NO_HARDWARE_RESPONSE
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1.UPBS] (Node 0xc1c338e0), AE_NO_HARDWARE_RESPONSE
ACPI-1287: *** Error: Method execution failed [\\_SB_.BAT1._BST] (Node 0xc1c33920), AE_NO_HARDWARE_RESPONSE
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-multimedia
To unsubscribe, send any mail to "[email protected]"
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"