SMC 2632W version 2
Ben Lovett <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.mobile |
|---|---|
| Message-ID | <[email protected]> |
Has anyone managed to get SMC's 2632W-V2 card working under 4.6? I had
to create a modified entry for this card, because they changed the
values returned when pccardd finds the card.
card "SMC" "2632W-V2"
config auto "wi" ? 0x10000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
Now the system finds the card, but it then errors out saying with the
following:
wi0 at port 0x240-0x27f irq 11 flags 0x10000 slot 0 on pccard0
wi0: timeout in wi_cmd 0x0000; event status 0x0000
wi0: timeout in wi_cmd 0x0000; event status 0x0000
wi0: timeout in wi_cmd 0x0000; event status 0x0000
wi0: init failed
wi0: timeout in wi_cmd 0x0021; event status 0x0000
wi0: timeout in wi_cmd 0x0021; event status 0x0000
wi0: mac read failed 5
device_probe_and_attach: wi0 attach returned 5
dumpcis output is attached.
Thanks,
Ben
smc2632-v2.txt
(text/plain, 1.5 KB)
Configuration data for card in slot 1
Tuple #1, code = 0x17 (Attribute memory descriptor), length = 3
000: d9 01 ff
Attribute memory device information:
Device number 1, type Function specific, WPS = ON
Speed = 250nS, Memory block size = 2Kb, 1 units
Tuple #2, code = 0x1d (Other conditions for attribute memory), length = 4
000: 03 d9 01 ff
(MWAIT) (3V card)
Tuple #3, code = 0x20 (Manufacturer ID), length = 4
000: bf 01 01 b3
PCMCIA ID = 0x1bf, OEM ID = 0xb301
Tuple #4, code = 0x21 (Functional ID), length = 2
000: 06 00
Network/LAN adapter
Tuple #5, code = 0x15 (Version 1 info), length = 16
000: 05 00 53 4d 43 00 32 36 33 32 57 2d 56 32 00 ff
Version = 5.0, Manuf = [SMC], card vers = [2632W-V2]
Tuple #6, code = 0x1a (Configuration map), length = 6
000: 01 02 00 08 03 ff
Reg len = 2, config register addr = 0x800, last config = 0x2
Registers: XX------ 1 bytes in subtuples
Tuple #7, code = 0x1b (Configuration entry), length = 16
000: c1 81 9d 71 b5 1e 2e 2e 2d fc 14 45 10 b8 ff 20
Config index = 0x1(default)
Interface byte = 0x81 (I/O) wait signal supported
Vcc pwr:
Nominal operating supply voltage: 3 x 1V, ext = 0x1e
Max current average over 1 second: 2.5 x 100mA
Max current average over 10 ms: 2.5 x 100mA
Power down supply current: 2.5 x 10mA
Wait scale Speed = 1.2 x 10 us
Card decodes 5 address lines, limited 8/16 Bit I/O
IRQ modes:
IRQs: 3 4 5 7 8 9 10 11 12 13 14 15
Max twin cards = 0
Misc attr: (Power down supported)
Tuple #8, code = 0xff (Terminator), length = 0
2 slots found