Gigabyte wireless network card
wiqd <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.mobile |
|---|---|
| Message-ID | <[email protected]> |
Greetings list,
Well here is my problem, I have a gigabyte pci wireless network card, I
cannot for the life of me find any more information on it from any
websites including the gigabyte website itself. My issue is that freebsd
4.10-STABLE will not see the card, i have tried everything i can find on
google and the freebsd websites and to no avail still do not have it
working, please find below a dmesg output, ifconfig output, kernel
config and uname output.
Thanks for any help anyone could offer.
kind regards,
Greg
## Dmesg
root@intraweb:/dev #> dmesg
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights
reserved.
FreeBSD 4.10-STABLE #1: Tue Sep 28 20:49:56 SAST 2004
[email protected]:/usr/obj/usr/src/sys/INTRAWEB
Timecounter "i8254" frequency 1193182 Hz
CPU: Intel Celeron (634.78-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x686 Stepping = 6
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 268435456 (262144K bytes)
config> di sn0
config> di lnc0
config> di ie0
config> di fe0
config> di ed0
config> di cs0
config> di fdc0
config> q
avail memory = 255754240 (249760K bytes)
Preloaded elf kernel "kernel" at 0xc0551000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc055109c.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 6 entries at 0xc00fdcd0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib2: <VIA 82C598MVP (Apollo MVP3) PCI-PCI (AGP) bridge> at device 1.0
on pci0
pci1: <PCI bus> on pcib2
pci1: <ATI Mach64-GZ graphics accelerator> at 0.0 irq 11
isab0: <VIA 82C686 PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C686 ATA66 controller> port 0x6400-0x640f at device 7.1
on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <VIA 83C572 USB controller> port 0x6800-0x681f irq 10 at device
7.2 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0x6c00-0x6c1f irq 10 at device
7.3 on pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
pci0: <unknown card> (vendor=0x1106, dev=0x3057) at 7.4
chip1: <VIA 82C686 AC97 Audio> port
0x7800-0x7803,0x7400-0x7403,0x7000-0x70ff irq 12 at device 7.5 on pci0
pci0: <unknown card> (vendor=0x1814, dev=0x0201) at 10.0 irq 12
rl0: <RealTek 8139 10/100BaseTX> port 0x7c00-0x7cff mem
0xe7002000-0xe70020ff irq 9 at device 11.0 on pci0
rl0: Ethernet address: 00:08:a1:45:1f:e2
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl1: <RealTek 8139 10/100BaseTX> port 0x8000-0x80ff mem
0xe7003000-0xe70030ff irq 11 at device 12.0 on pci0
rl1: Ethernet address: 00:08:a1:45:21:e4
miibus1: <MII bus> on rl1
rlphy1: <RealTek internal media interface> on miibus1
rlphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib1: <Host to PCI bridge> on motherboard
pci2: <PCI bus> on pcib1
eisa0: <EISA bus> on motherboard
eisa0: unknown card FP@0000 (0x1a000000) at slot 7
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xd0000-0xd7fff on isa0
pmtimer0 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
DUMMYNET initialized (011031)
IP packet filtering initialized, divert enabled, rule-based forwarding
enabled, default to accept, logging limited to 100 packets/entry by
default
BRIDGE 020214 loaded
ad0: 38166MB <ST340015A> [77545/16/63] at ata0-master UDMA66
ad1: 76319MB <ST380011A> [155061/16/63] at ata0-slave UDMA66
acd0: CDROM <IDE/ATAPI CD-ROM 44XS> at ata1-slave PIO4
Mounting root from ufs:/dev/ad0s1a
rl0: promiscuous mode enabled
## ifconfig
root@intraweb:/dev #> ifconfig
rl0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
inet 192.168.0.1 netmask 0xffffff00 broadcast 192.168.0.255
inet6 fe80::208:a1ff:fe45:1fe2%rl0 prefixlen 64 scopeid 0x1
ether 00:08:a1:45:1f:e2
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
rl1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet 172.16.10.2 netmask 0xffff0000 broadcast 172.16.255.255
inet6 fe80::208:a1ff:fe45:21e4%rl1 prefixlen 64 scopeid 0x2
ether 00:08:a1:45:21:e4
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
lp0: flags=8810<POINTOPOINT,SIMPLEX,MULTICAST> mtu 1500
sl0: flags=c010<POINTOPOINT,LINK2,MULTICAST> mtu 552
faith0: flags=8002<BROADCAST,MULTICAST> mtu 1500
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x6
inet 127.0.0.1 netmask 0xff000000
ppp0: flags=8010<POINTOPOINT,MULTICAST> mtu 1500
## kernel
root@intraweb:/dev #> cat /usr/src/sys/i386/conf/INTRAWEB
#
# GENERIC -- Generic kernel configuration file for FreeBSD/i386
#
# For more information on this file, please read the handbook section on
# Kernel Configuration Files:
#
#
http://www.FreeBSD.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig-config.html
#
# The handbook is also available locally in /usr/share/doc/handbook
# if you've installed the doc distribution, otherwise always see the
# FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the
# latest information.
#
# An exhaustive list of options and more detailed explanations of the
# device lines is also present in the ./LINT configuration file. If you
are
# in doubt as to the purpose or necessity of a line, check first in
LINT.
#
# $FreeBSD: src/sys/i386/conf/GENERIC,v 1.246.2.48 2002/08/31 20:28:26
obrien Exp $
machine i386
cpu I386_CPU
cpu I486_CPU
cpu I586_CPU
cpu I686_CPU
ident GENERIC
maxusers 0
#makeoptions DEBUG=-g #Build kernel with gdb(1) debug
symbols
options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
options INET6 #IPv6 communications protocols
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep
this!]
options SOFTUPDATES #Enable FFS soft updates support
options UFS_DIRHASH #Improve performance on big
directories
options MFS #Memory Filesystem
options MD_ROOT #MD is a potential root device
options NFS #Network Filesystem
options NFS_ROOT #NFS usable as root device, NFS
required
options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
options CD9660_ROOT #CD-ROM usable as root, CD9660
required
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP
THIS!]
options SCSI_DELAY=15000 #Delay (in ms) before probing
SCSI
options UCONSOLE #Allow users to grab the console
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time
extensions
options _KPOSIX_PRIORITY_SCHEDULING
options ICMP_BANDLIM #Rate limit bad replies
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
options AHC_REG_PRETTY_PRINT # Print register bitfields in
debug
# output. Adds ~128k to driver.
options AHD_REG_PRETTY_PRINT # Print register bitfields in
debug
# output. Adds ~215k to driver.
# To make an SMP kernel, the next two are needed
#options SMP # Symmetric MultiProcessor
Kernel
#options APIC_IO # Symmetric (APIC) I/O
device isa
device eisa
device pci
# Floppy drives
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
device fd1 at fdc0 drive 1
#
# If you have a Toshiba Libretto with its Y-E Data PCMCIA floppy,
# don't use the above line for fdc0 but the following one:
#device fdc0
# ATA and ATAPI devices
device ata0 at isa? port IO_WD1 irq 14
device ata1 at isa? port IO_WD2 irq 15
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
device atapist # ATAPI tape drives
options ATA_STATIC_ID #Static device numbering
# SCSI Controllers
device ahb # EISA AHA1742 family
device ahc # AHA2940 and onboard AIC7xxx devices
device ahd # AHA39320/29320 and onboard AIC79xx
devices
device amd # AMD 53C974 (Tekram DC-390(T))
device isp # Qlogic family
device mpt # LSI-Logic MPT/Fusion
device ncr # NCR/Symbios Logic
device sym # NCR/Symbios Logic (newer chipsets)
options SYM_SETUP_LP_PROBE_MAP=0x40
# Allow ncr to attach legacy NCR devices
when
# both sym and ncr are configured
device adv0 at isa?
device adw
device bt0 at isa?
device aha0 at isa?
device aic0 at isa?
device ncv # NCR 53C500
device nsp # Workbit Ninja SCSI-3
device stg # TMC 18C30/18C50
# SCSI peripherals
device scbus # SCSI bus (required)
device da # Direct Access (disks)
device sa # Sequential Access (tape etc)
device cd # CD
device pass # Passthrough device (direct SCSI
access)
# RAID controllers interfaced to the SCSI subsystem
device asr # DPT SmartRAID V, VI and Adaptec SCSI
RAID
device dpt # DPT Smartcache - See LINT for options!
device iir # Intel Integrated RAID
device mly # Mylex AcceleRAID/eXtremeRAID
device ciss # Compaq SmartRAID 5* series
# RAID controllers
device aac # Adaptec FSA RAID, Dell PERC2/PERC3
device aacp # SCSI passthrough for aac (requires
CAM)
device ida # Compaq Smart RAID
device amr # AMI MegaRAID
device mlx # Mylex DAC960 family
device twe # 3ware Escalade
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1 flags 0x1
device psm0 at atkbdc? irq 12
device vga0 at isa?
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa? flags 0x100
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device vt0 at isa?
#options XSERVER # support for X server on a vt
console
#options FAT_CURSOR # start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT
lines
#options PCVT_SCANSET=2 # IBM keyboards are non-std
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# Power management support (see LINT for more options)
device apm0 at nexus? disable flags 0x20 # Advanced Power
Management
# PCCARD (PCMCIA) support
device card
device pcic0 at isa? irq 0 port 0x3e0 iomem 0xd0000
device pcic1 at isa? irq 0 port 0x3e2 iomem 0xd4000 disable
# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
device sio2 at isa? disable port IO_COM3 irq 5
device sio3 at isa? disable port IO_COM4 irq 9
# Parallel port
device ppc0 at isa? irq 7
device ppbus # Parallel port bus (required)
device lpt # Printer
device plip # TCP/IP over parallel
device ppi # Parallel port interface device
#device vpo # Requires scbus and da
# PCI Ethernet NICs.
device de # DEC/Intel DC21x4x (``Tulip'')
device em # Intel PRO/1000 adapter Gigabit
Ethernet Card (``Wiseman'')
device txp # 3Com 3cR990 (``Typhoon'')
device vx # 3Com 3c590, 3c595 (``Vortex'')
# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these
NICs!
device miibus # MII bus support
device dc # DEC/Intel 21143 and various workalikes
device fxp # Intel EtherExpress PRO/100B (82557,
82558)
device pcn # AMD Am79C97x PCI 10/100 NICs
device rl # RealTek 8129/8139
device sf # Adaptec AIC-6915 (``Starfire'')
device sis # Silicon Integrated Systems SiS 900/SiS
7016
device ste # Sundance ST201 (D-Link DFE-550TX)
device tl # Texas Instruments ThunderLAN
device tx # SMC EtherPower II (83c170 ``EPIC'')
device vr # VIA Rhine, Rhine II
device wb # Winbond W89C840F
device xl # 3Com 3c90x (``Boomerang'',
``Cyclone'')
device bge # Broadcom BCM570x (``Tigon III'')
# ISA Ethernet NICs.
# 'device ed' requires 'device miibus'
device ed0 at isa? port 0x280 irq 10 iomem 0xd8000
device ex
device ep
device fe0 at isa? port 0x300
# Xircom Ethernet
device xe
# PRISM I IEEE 802.11b wireless NIC.
device awi
# WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really
# exists only as a PCMCIA device, so there is no ISA attachment needed
# and resources will always be dynamically assigned by the pccard code.
device wi
# Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below
will
# work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP
# mode (the factory default). If you set the switches on your ISA
# card for a manually chosen I/O address and IRQ, you must specify
# those parameters here.
device an
# The probe order of these is presently determined by
i386/isa/isa_compat.c.
device ie0 at isa? port 0x300 irq 10 iomem 0xd0000
#device le0 at isa? port 0x300 irq 5 iomem 0xd0000
device lnc0 at isa? port 0x280 irq 10 drq 0
device cs0 at isa? port 0x300
device sn0 at isa? port 0x300 irq 10
# Pseudo devices - the number indicates how many units to allocate.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
pseudo-device sl 1 # Kernel SLIP
pseudo-device ppp 1 # Kernel PPP
pseudo-device tun # Packet tunnel.
pseudo-device pty # Pseudo-ttys (telnet etc)
pseudo-device md # Memory "disks"
pseudo-device gif # IPv6 and IPv4 tunneling
pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation)
# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device bpf #Berkeley packet filter
# USB support
device uhci # UHCI PCI->USB interface
device ohci # OHCI PCI->USB interface
device usb # USB Bus (required)
device ugen # Generic
device uhid # "Human Interface Devices"
device ukbd # Keyboard
device ulpt # Printer
device umass # Disks/Mass storage - Requires scbus
and da
device ums # Mouse
device uscanner # Scanners
device urio # Diamond Rio MP3 Player
# USB Ethernet, requires mii
device aue # ADMtek USB ethernet
device cue # CATC USB ethernet
device kue # Kawasaki LSI USB ethernet
options RANDOM_IP_ID
options MROUTING # Multicast routing
options IPFIREWALL #firewall
options IPFIREWALL_VERBOSE #enable logging to syslogd(8)
options IPFIREWALL_FORWARD #enable transparent proxy
support
options IPFIREWALL_VERBOSE_LIMIT=100 #limit verbosity
options IPFIREWALL_DEFAULT_TO_ACCEPT #allow everything by
default
options IPDIVERT # IPDIVERT enables the divert
IP sockets, used by ''ipfw divert''
options ACCEPT_FILTER_DATA
options ACCEPT_FILTER_HTTP
options IPSTEALTH #support for stealth forwarding
options TCPDEBUG
options TCP_DROP_SYNFIN #drop TCP packets with SYN+FIN
options DUMMYNET
options BRIDGE
options HZ=1000
## uname -a
root@intraweb:/dev #> uname -a
FreeBSD intraweb.propdata.co.za 4.10-STABLE FreeBSD 4.10-STABLE #1: Tue
Sep 28 20:49:56 SAST 2004
[email protected]:/usr/obj/usr/src/sys/INTRAWEB i386
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"