Re: Thinkpad 600e interrupt storm

Hi,

Okay I have added 'smapi_load="YES"' to /boot/loader.conf
I have booted with that setup .
Here is my dmesg:

Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
    The Regents of the University of California. All rights reserved.
FreeBSD 5.4-PRERELEASE #14: Thu Mar 10 16:44:40 EST 2005
    [email protected]:/usr/obj/usr/src/sys/SLACKER
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Pentium II/Pentium II Xeon/Celeron (363.96-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x66a  Stepping = 10
  
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory  = 134021120 (127 MB)
avail memory = 121507840 (115 MB)
npx0: <math processor> on motherboard
npx0: INT 16 interface
smapi0: <SMAPI BIOS> at iomem 0xfe9a0-0xfe9bf on motherboard
smapi0: Version: 0.83, Length: 32, Checksum: 0x43
smapi0: Information=0x7<REAL_VM86,PROTECTED_16,PROTECTED_32>
cpu0 on motherboard
apm0: <APM BIOS> on motherboard
apm0: found APM BIOS v1.2, connected at v1.2
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> pcibus 0 on motherboard
pir0: <PCI Interrupt Routing Table: 5 Entries> on motherboard
pci0: <PCI bus> on pcib0
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 
0x40000000-0x43ffffff at device 0.0 on pci0
pcib1: <PCIBIOS PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
cbb0: <TI1251 PCI-CardBus Bridge> mem 0x50102000-0x50102fff irq 11 at 
device 2.0 on pci0
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb1: <TI1251 PCI-CardBus Bridge> mem 0x50101000-0x50101fff irq 11 at 
device 2.1 on pci0
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
pci0: <multimedia, audio> at device 6.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port 
0xfcf0-0xfcff,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 7.1 on pci0
ata0: channel #0 on atapci0
ata1: channel #1 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x8400-0x841f irq 
11 at device 7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
orm0: <ISA Option ROM> at iomem 0xc0000-0xcbfff on isa0
pmtimer0 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse Explorer, device ID 4
fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5 irq 6 drq 2 on isa0
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Parallel port> at port 0x3bc-0x3c3 irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
ppi0: <Parallel I/O> on ppbus0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
unknown: <PNP0303> can't assign resources (port)
unknown: <IBM3780> can't assign resources (irq)
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0c02> can't assign resources (port)
unknown: <PNP0400> can't assign resources (port)
pcm0: <CS423x-PCI> at port 0x220-0x233,0x388-0x38b,0x530-0x537 irq 5 drq 
0,1 flags 0x10 on isa0
unknown: <IBM0071> can't assign resources (port)
unknown: <PNP0e03> can't assign resources (port)
unknown: <PNP0680> can't assign resources (port)
unknown: <PNP0680> can't assign resources (port)
Timecounters tick every 10.000 msec
ad0: 11513MB <FUJITSU MHK2120AT/D834> [23392/16/63] at ata0-master UDMA33
acd0: CDROM <TOSHIBA CD-ROM XM-1902B/1717> at ata1-master PIO4
ed1: <D-Link DFE-670TXD> at port 0x100-0x11f irq 11 function 0 config 32 
on pccard1
ed1: Ethernet address: 00:50:ba:cb:54:f0
ed1: if_start running deferred for Giant
ed1: type DL10022 (16 bit)
miibus0: <MII bus> on ed1
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
Mounting root from ufs:/dev/ad0s1a


Now I see the smapi in the dmesg. The question is where do we go from here?

Sincerely,
Brendhan
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-mobile
To unsubscribe, send any mail to "[email protected]"