https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=290793
--- Comment #16 from Bjoern A. Zeeb <[email protected]> ---
(In reply to Konstantin Belousov from comment #15)
Yes, your comment came overlapping with me typing the before already.
[3.686949] mlx5_core0: <mlx5_core> mem 0x383ffc000000-0x383ffdffffff irq 32 at
device 0.0 on pci3
[3.694355] mlx5: Mellanox Core driver 3.7.1 (November 2021) << missing \n?
[4.061886] mlx5_core0: attempting to allocate 15 MSI-X vectors (128 supported)
..
[4.143047] mlx5_core0: using IRQs 72-86 for MSI-X
[4.166061] mlx5_core0: WARN: mlx5_vsc_set_space:125:(pid 0): Space 0x7 is not
supported.
[4.172669] mlx5_core0: WARN: mlx5_fwdump_prep:99:(pid 0): VSC scan space is not
supported
[4.179641] mlx5_core: INFO: (mlx5_core0): E-Switch: Total vports 11, l2 table
size(65536), per vport: max uc(1024) max mc(16384)
[4.225477] pci0:2:0:1: reprobing on driver added
[4.231668] mlx5_core1: <mlx5_core> mem 0x383ffa000000-0x383ffbffffff irq 32 at
device 0.1 on pci3
[4.575887] mlx5_core1: attempting to allocate 15 MSI-X vectors (128 supported)
[4.657320] mlx5_core1: using IRQs 87-101 for MSI-X
[4.685698] mlx5_core1: WARN: mlx5_vsc_set_space:125:(pid 0): Space 0x7 is not
supported.
[4.692308] mlx5_core1: WARN: mlx5_fwdump_prep:99:(pid 0): VSC scan space is not
supported
[4.699282] mlx5_core: INFO: (mlx5_core1): E-Switch: Total vports 11, l2 table
size(65536), per vport: max uc(1024) max mc(16384)
[4.773045] mce0: Ethernet address: 7c:fe:90:30:xx:xx
[4.776802] mce0: link state changed to DOWN
[4.778092] mlx5_core0: ERR: mlx5_cmd_check:714:(pid 0): ACCESS_REG(0x805)
op_mod(0x1) failed, status bad parameter(0x3), syndrome (0x6c4d48)
[4.795174] mlx5_core0: ERR: mlx5_cmd_check:714:(pid 0): ACCESS_REG(0x805)
op_mod(0x1) failed, status bad parameter(0x3), syndrome (0x6c4d48)
[4.882680] mce1: bpf attached
[4.884171] mce1: Ethernet address: 7c:fe:90:30:xx:xx
[4.887923] mce1: link state changed to DOWN
[4.889062] mlx5_core1: ERR: mlx5_cmd_check:714:(pid 0): ACCESS_REG(0x805)
op_mod(0x1) failed, status bad parameter(0x3), syndrome (0x6c4d48)
[4.906441] mlx5_core1: ERR: mlx5_cmd_check:714:(pid 0): ACCESS_REG(0x805)
op_mod(0x1) failed, status bad parameter(0x3), syndrome (0x6c4d48)
How do I update the firmware to the right version?
Sorry I am asking for extra hand holding but I figure it'll help to make
progress faster.
--
You are receiving this mail because:
You are the assignee for the bug.
lmpx.com only provides a reader for public news (NNTP) servers. It is not
affiliated with the servers or forums shown here and is not responsible for
the content of articles, which is written by their respective authors.