Re: rge(4) RTL8126 simple testing

Kevin Lo <[email protected]>
Newsgroups gmane.os.freebsd.devel.net
Message-ID <[email protected]> 
On Wed, Mar 04, 2026 at 04:02:37PM -0500, Sean C. Farley wrote:
> 
> On Sat, 28 Feb 2026, Sean C. Farley wrote:
> 
> > I recently upgraded my home network using a few BrosTrend 5Gb cards
> > (RTL8126) with 14-STABLE (1eb2beb3686c) and the latest commit (3170b35)
> > to the GitHub repo for if_rge.  It was either these cards or a couple of
> > Intel X550-T2 cards, but less power and less heat were the deciding
> > factors.
> > 
> > For the most part, they seem to work very well, except that they cannot
> > negotiate a 2500Base-T connection.  They can negotiate 1000baseT and
> > 5000Base-T.  This was with two different cards connecting to two
> > different devices.  If manually set, they will try for awhile than
> > fall-back to 1000baseT.
> > 
> > One other oddity is that rge0 has "ClockPM disabled", but I have not
> > looked into that.
> > 
> > The networking hardware:
> > - 3 BrosTrend 5Gb NIC's[1]  (5Gb)
> > - Zyxel NWA130BE[2]  (2.5Gb port)
> > - TRENDnet TEG-S591[3]  (connected the NIC to its 10Gb port)
> > - Nokia ONT XS-010X-Q[4]  (10Gb port)
> > 
> > ifconfig:
> > rge0: flags=1008843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,LOWER_UP>
> > metric 0 mtu 1500
> > 	options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM>
> > 	capabilities=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM>
> >        media: Ethernet autoselect (5000Base-T <full-duplex>)
> > 	status: active
> > 	supported media:
> > 		media autoselect
> > 		media 5000Base-T mediaopt full-duplex
> > 		media 5000Base-T
> > 		media 2500Base-T mediaopt full-duplex
> > 		media 2500Base-T
> > 		media 1000baseT mediaopt full-duplex
> > 		media 1000baseT
> > 		media 100baseTX mediaopt full-duplex
> > 		media 100baseTX
> > 		media 10baseT/UTP mediaopt full-duplex
> > 		media 10baseT/UTP
> > 	nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
> > 	drivername: rge0
> > rge1:
> > flags=1008943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST,LOWER_UP>
> > metric 0 mtu 1500
> > 	options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM>
> > 	capabilities=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM>
> > 	media: Ethernet autoselect (5000Base-T <full-duplex>)
> > 	status: active
> > 	supported media:
> > 		media autoselect
> > 		media 5000Base-T mediaopt full-duplex
> > 		media 5000Base-T
> > 		media 2500Base-T mediaopt full-duplex
> > 		media 2500Base-T
> > 		media 1000baseT mediaopt full-duplex
> > 		media 1000baseT
> > 		media 100baseTX mediaopt full-duplex
> > 		media 100baseTX
> > 		media 10baseT/UTP mediaopt full-duplex
> > 		media 10baseT/UTP
> > 	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
> > 	drivername: rge1
> > rge2:
> > flags=1008943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST,LOWER_UP>
> > metric 0 mtu 1500
> > 	options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM>
> > 	capabilities=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM>
> > 	media: Ethernet Other (1000baseT <full-duplex>)
> > 	status: active
> > 	supported media:
> > 		media autoselect
> > 		media 5000Base-T mediaopt full-duplex
> > 		media 5000Base-T
> > 		media 2500Base-T mediaopt full-duplex
> > 		media 2500Base-T
> > 		media 1000baseT mediaopt full-duplex
> > 		media 1000baseT
> > 		media 100baseTX mediaopt full-duplex
> > 		media 100baseTX
> > 		media 10baseT/UTP mediaopt full-duplex
> > 		media 10baseT/UTP
> > 	nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
> > 	drivername: rge2
> > 
> > pciconf:
> > rge0@pci0:1:0:0:	class=0x020000 rev=0x01 hdr=0x00 vendor=0x10ec
> > device=0x8126 subvendor=0x10ec subdevice=0x0123
> >    vendor     = 'Realtek Semiconductor Co., Ltd.'
> >    device     = 'RTL8126 5GbE Controller'
> >    class      = network
> >    subclass   = ethernet
> >    bar   [10] = type I/O Port, range 32, base 0xe000, size 256, enabled
> >    bar   [18] = type Memory, range 64, base 0xf7600000, size 65536, enabled
> >    bar   [20] = type Memory, range 64, base 0xf7610000, size 16384, enabled
> >    cap 01[40] = powerspec 3  supports D0 D1 D2 D3  current D0
> >    cap 05[50] = MSI supports 1 message, 64 bit, vector masks enabled
> > with 1 message
> >    cap 10[70] = PCI-Express 2 endpoint MSI 1 max data 256(512) RO
> >                 max read 512
> >                 link x1(x1) speed 8.0(8.0) ASPM disabled(L0s/L1) ClockPM
> > disabled
> >    cap 11[b0] = MSI-X supports 32 messages
> >                 Table in map 0x20[0x0], PBA in map 0x20[0x800]
> >    cap 03[d0] = VPD
> >    ecap 0001[100] = AER 2 0 fatal 0 non-fatal 1 corrected
> >    ecap 0002[148] = VC 1 max VC0
> >    ecap 0003[170] = Serial 1 01000000684ce000
> >    ecap 0019[180] = PCIe Sec 1 lane errors 0
> >    ecap 0017[190] = TPH Requester 1
> >    ecap 0018[21c] = LTR 1
> >    ecap 001e[224] = L1 PM Substates 1
> >    ecap 000b[234] = Vendor [1] ID 0002 Rev 4 Length 256
> > rge1@pci0:4:0:0:	class=0x020000 rev=0x01 hdr=0x00 vendor=0x10ec
> > device=0x8126 subvendor=0x10ec subdevice=0x0123
> >    vendor     = 'Realtek Semiconductor Co., Ltd.'
> >    device     = 'RTL8126 5GbE Controller'
> >    class      = network
> >    subclass   = ethernet
> >    bar   [10] = type I/O Port, range 32, base 0xd000, size 256, enabled
> >    bar   [18] = type Memory, range 64, base 0xf7500000, size 65536, enabled
> >    bar   [20] = type Memory, range 64, base 0xf7510000, size 16384, enabled
> >    cap 01[40] = powerspec 3  supports D0 D1 D2 D3  current D0
> >    cap 05[50] = MSI supports 1 message, 64 bit, vector masks enabled
> > with 1 message
> >    cap 10[70] = PCI-Express 2 endpoint MSI 1 max data 256(512) RO
> >                 max read 512
> >                 link x1(x1) speed 8.0(8.0) ASPM disabled(L0s/L1) ClockPM
> > enabled
> >    cap 11[b0] = MSI-X supports 32 messages
> >                 Table in map 0x20[0x0], PBA in map 0x20[0x800]
> >    cap 03[d0] = VPD
> >    ecap 0001[100] = AER 2 0 fatal 0 non-fatal 0 corrected
> >    ecap 0002[148] = VC 1 max VC0
> >    ecap 0003[170] = Serial 1 01000000684ce000
> >    ecap 0019[180] = PCIe Sec 1 lane errors 0
> >    ecap 0017[190] = TPH Requester 1
> >    ecap 0018[21c] = LTR 1
> >    ecap 001e[224] = L1 PM Substates 1
> >    ecap 000b[234] = Vendor [1] ID 0002 Rev 4 Length 256
> > rge2@pci0:5:0:0:	class=0x020000 rev=0x01 hdr=0x00 vendor=0x10ec
> > device=0x8126 subvendor=0x10ec subdevice=0x0123
> >    vendor     = 'Realtek Semiconductor Co., Ltd.'
> >    device     = 'RTL8126 5GbE Controller'
> >    class      = network
> >    subclass   = ethernet
> >    bar   [10] = type I/O Port, range 32, base 0xc000, size 256, enabled
> >    bar   [18] = type Memory, range 64, base 0xf7400000, size 65536, enabled
> >    bar   [20] = type Memory, range 64, base 0xf7410000, size 16384, enabled
> >    cap 01[40] = powerspec 3  supports D0 D1 D2 D3  current D0
> >    cap 05[50] = MSI supports 1 message, 64 bit, vector masks enabled
> > with 1 message
> >    cap 10[70] = PCI-Express 2 endpoint MSI 1 max data 256(512) RO
> >                 max read 512
> >                 link x1(x1) speed 8.0(8.0) ASPM disabled(L0s/L1) ClockPM
> > enabled
> >    cap 11[b0] = MSI-X supports 32 messages
> >                 Table in map 0x20[0x0], PBA in map 0x20[0x800]
> >    cap 03[d0] = VPD
> >    ecap 0001[100] = AER 2 0 fatal 0 non-fatal 0 corrected
> >    ecap 0002[148] = VC 1 max VC0
> >    ecap 0003[170] = Serial 1 01000000684ce000
> >    ecap 0019[180] = PCIe Sec 1 lane errors 0
> >    ecap 0017[190] = TPH Requester 1
> >    ecap 0018[21c] = LTR 1
> >    ecap 001e[224] = L1 PM Substates 1
> >    ecap 000b[234] = Vendor [1] ID 0002 Rev 4 Length 256
> > 
> > Sean
> >  1. https://www.brostrend.com/products/p2
> >  2. https://www.zyxel.com/us/en-us/products/wireless/be11000-6-stream-wifi-7-triple-radio-nebulaflex-access-point-nwa130be
> >  3. https://www.trendnet.com/products/2_5g-10g-switches/9-port-multi-gig-switch-TEG-S591-v1
> >  4. https://www.nokia.com/asset/210704/
> 
> I have spent awhile trying different things yet cannot get these to work at
> 2.5G.  The Realtek vendor driver cannot negotiate at 2.5G nor can Linux 6.18
> (Arch Linux).
> 
> Important details:
> - FreeBSD dmesg chip rev: RTL8126_2 (0x64a00000)

Since all the RTL8126 chip revisions I have on hand are RTL8126_1 (0x64900000), I went ahead and bought the BrosTrend 5G network card you recommended.
Purchasing directly from the BrosTrend official website wasn't an option 
since they don't ship to Taiwan, so I ordered from Amazon [1] instead.
Unfortunately, the one I received turned out to be RTL8126_1 as well. :(

[1] https://www.amazon.com/dp/B0CYZ9M3LR
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.