https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=265714
--- Comment #82 from Tomasz "CeDeROM" CEDRO <[email protected]> ---
Thank you Kevin :-)
The mainboard is new and still under warranty so I don't suspect a defect
unless it was manufacturing defect or bad design. I took this one because it is
one of few that still has some spare PCI-e slots and pretty decent chipset. I
have reported Ethernet issues to the vendor some months ago and they sent this
to HQ for verification but I got no response since then. This mainboard has
thousands of options in BIOS [2] which most of them are set to Auto, I only
choose these which I know about.. maybe this "AI"/"Auto" is the problem because
mobo can change settings on each boot or even runtime no clue.
Ah I saw two days ago new BIOS showed up, will update and maybe that helps
somehow :-)
Another Idea is to maybe search for this I226V on the PCIe and just try another
one to exclude faulty hardware?
By the way there is one difference with IX driver - ifconfig shows "status: no
carrier" when interface is down even if cable is attached, while IGC shows
"status: active" when cable is attached but interface is down.
# uname -a
FreeBSD hexagon 14.4-RELEASE-p8 FreeBSD 14.4-RELEASE-p8
cederom-releng-14.4.8-igc_test_20260810-n273771-e99dffa6c4c8 GENERIC amd64
# sysctl hw.iommu
hw.iommu.batch_coalesce: 100
hw.iommu.tbl_pagecnt: 0
hw.iommu.dmar.timeout: 1000000
# sysctl dev.dmar
sysctl: unknown oid 'dev.dmar'
# kenv | egrep 'iommu|dmar'
# dmesg -a | egrep -i 'dmar|iommu|fault|remap|vbox|vmm'
[1] Trying to mount root from zfs:znvd/ROOT/default []...
[37] add net default: gateway XXX fib 0: route already in table
[38] ipfw2 (+ipv6) initialized, divert loadable, nat loadable, default to deny,
logging disabled
[38] 00000 check-state :default
[38] 00000 allow tcp from me to any setup keep-state :default
[38] 00000 allow udp from me to any keep-state :default
[38] 00000 allow icmp from me to any keep-state :default
[38] 00000 allow ipv6-icmp from me to any keep-state :default
[45] Starting default mousedmoused: unable to open /dev/psm0: No such file or
directory
[10978] vboxdrv: XXXXXXXXXXXXXXXX VMMR0.r0
[10978] vboxdrv: XXXXXXXXXXXXXXXX VBoxDDR0.r0
[10978] VMMR0InitVM: eflags=40246 fKernelFeatures=0x2
(SUPKERNELFEATURES_SMAP=1)
[25528] vboxdrv: XXXXXXXXXXXXXXXX VMMR0.r0
[25528] vboxdrv: XXXXXXXXXXXXXXXX VBoxDDR0.r0
[25528] VMMR0InitVM: eflags=40246 fKernelFeatures=0x2
(SUPKERNELFEATURES_SMAP=1)
# kldstat
Id Refs Address Size Name
1 140 0xffffffff80200000 1f44e80 kernel
2 1 0xffffffff82145000 79b0 hidraw.ko
3 1 0xffffffff8214d000 7808 cryptodev.ko
4 1 0xffffffff82155000 133b0 ntb_hw_intel.ko
5 2 0xffffffff82169000 6930 ntb.ko
6 1 0xffffffff82170000 b758 cuse.ko
7 1 0xffffffff8217c000 43c0 cpuctl.ko
8 1 0xffffffff82181000 3870 hgame.ko
9 5 0xffffffff82185000 4e80 hidmap.ko
10 1 0xffffffff8218a000 27670 fusefs.ko
11 3 0xffffffff821b2000 8e700 vboxdrv.ko
12 1 0xffffffff82242000 61b88 linux64.ko
13 7 0xffffffff822a4000 219a0 linux_common.ko
14 3 0xffffffff822c6000 6a688 linux.ko
15 1 0xffffffff82331000 5ee700 zfs.ko
16 1 0xffffffff82920000 5b18 sysctlinfo.ko
17 1 0xffffffff82926000 36c8 coretemp.ko
18 1 0xffffffff8292a000 26038 hwpmc.ko
19 1 0xffffffff82951000 3368 sysctlbyname_improved.ko
20 1 0xffffffff83b70000 3560 fdescfs.ko
21 1 0xffffffff83b74000 149458 nvidia-modeset.ko
22 1 0xffffffff83e00000 6791be0 nvidia.ko
23 1 0xffffffff83cbe000 3400 uchcom.ko
24 1 0xffffffff83cc2000 4e10 ucom.ko
25 1 0xffffffff83cc7000 2278 pty.ko
26 1 0xffffffff83cca000 73c0 linprocfs.ko
27 1 0xffffffff83cd2000 440c linsysfs.ko
28 1 0xffffffff83cd7000 3390 acpi_wmi.ko
29 1 0xffffffff83cdb000 21e8 hcons.ko
30 1 0xffffffff83cde000 21e8 hms.ko
31 1 0xffffffff83ce1000 21e8 hsctrl.ko
32 1 0xffffffff83ce4000 4250 ichsmb.ko
33 1 0xffffffff83ce9000 2178 smbus.ko
34 2 0xffffffff83cec000 4248 vboxnetflt.ko
35 2 0xffffffff83cf1000 abb8 netgraph.ko
36 1 0xffffffff83cfc000 31e0 ng_ether.ko
37 1 0xffffffff83d00000 55f0 vboxnetadp.ko
38 1 0xffffffff83d06000 3360 uhid.ko
39 1 0xffffffff83d0a000 3360 wmt.ko
40 1 0xffffffff83d0e000 f5b0 snd_uaudio.ko
41 1 0xffffffff83d1e000 4364 ums.ko
42 1 0xffffffff83d23000 28450 ipfw.ko
43 1 0xffffffff83d4c000 4b10 nullfs.ko
# ps auxww | egrep -i 'vbox|virtualbox'
XXX 73148 0.0 0.3 584796 267312 - SNs 23:04 0:04.30
/usr/local/lib/virtualbox/VirtualBox
XXX 74416 0.0 0.0 33356 16480 - SN 23:04 0:04.98
/usr/local/lib/virtualbox/VBoxXPCOMIPCD
XXX 75694 0.0 0.0 96348 35212 - SN 23:04 0:11.61
/usr/local/lib/virtualbox/VBoxSVC --auto-shutdown
root 887 0.0 0.0 13836 2316 1 S+ 00:08 0:00.00
egrep -i vbox|virtualbox
# ifconfig -a
igc0: flags=1008843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,LOWER_UP> metric 0
mtu 1500
options=4e527bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,HWSTATS,MEXTPG>
ether XXX
inet XXX netmask XXX broadcast XXX
media: Ethernet autoselect (1000baseT <full-duplex>)
status: active
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
ix0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=4e53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,HWSTATS,MEXTPG>
ether XXX
media: Ethernet autoselect
status: no carrier
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
ix1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=4e53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,HWSTATS,MEXTPG>
ether XXX
media: Ethernet autoselect
status: no carrier
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
ix2: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=4e53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,HWSTATS,MEXTPG>
ether XXX
media: Ethernet autoselect
status: no carrier
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
ix3: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=4e53fbb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,WOL_UCAST,WOL_MCAST,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6,HWSTATS,MEXTPG>
ether XXX
media: Ethernet autoselect
status: no carrier
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
lo0: flags=1008049<UP,LOOPBACK,RUNNING,MULTICAST,LOWER_UP> metric 0 mtu 16384
options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6>
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x6
groups: lo
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
# pciconf -t -v
pciconf: illegal option -- t
usage: pciconf -l [-BbcevV] [device]
pciconf -a device
pciconf -r [-b | -h] device addr[:addr2]
pciconf -w [-b | -h] device addr value
pciconf -D [-b | -h | -x] device bar [start [count]]
Regarding the commits none of these two applies cleanly on my releng/14.4,
below is the history that applies okay:
2f85437bf220 (HEAD -> cederom-releng-14.4.8-igc_test_20260813) igc: Remove
invalid debug ring pointer iteration
0d212a99a907 igc: Add led(4) identification support
e7ec9d32123a igc: Avoid a signed shift while assembling the PHY ID
8580a90787de igc: Export EEE Low Power Idle counters
8556b22ae729 igc: Check PHY control register reads
1eaf086ad2ba igc: fix data type in MAC hash
b5b7f2eb2582 igc: fix data type in MAC hash
25a900eea8d4 igc: fix MAC address hash bit shift
7843123f8673 igc: fix iterator type
3d73fda88d7a igc: Avoid a signed multicast bitmap shift
e99dffa6c4c8 (cederom/cederom-releng-14.4.8-igc_test_20260810,
cederom-releng-14.4.8-igc_test_20260810) igc: Correct descriptor control
programming
18774c90fb02 (cederom/cederom-releng-14.4.8-igc_test_20260803,
cederom-releng-14.4.8-igc_test_20260803) igc: Add VLAN hardware filtering
c1bc2da741d5 igc: Correct hardware error statistics
e80624657a23 igc: Work around I225 v1 minimum IPG erratum
8429f0391c11 igc: Disable PCIe L1.2 on I225
ea774409c9ca igc: Apply ASPM L1.2 workaround to all I226 devices
df561a9ea5f9 igc: Disable ASPM L1.2 on I226 to prevent RX stalls
4472d239ff5b igc(4): document adaptive interrupt moderation
53408cbd10c1 igc: count TSO wire segments in the AIM counters
f94e9349b389 igc: use packet-size AIM
fe2c8e215ccf igc: synchronize interrupt moderation state
fdf2a8ad9699 igc: make AIM counter sampling coherent
dc0fd5a3b87b igc: fix RX accounting for multi-descriptor packets
d6f358d9412c igc.4: Describe better
a3a185dba982 igc: use newly exposed RSS hash key API rather than ad-hoc hashing
518828a76cef pci: Add L1 PM definitions
d9b8b38e449f rss: Enable portions of RSS globally to enable symmetric hashing
3de2d29b088e (tag: release/14.4.0-p8, origin/releng/14.4, github/releng/14.4,
cederom/releng/14.4, releng/14.4) Add UPDATING entries and bump version
I will take a look and sort out what else is missing. Hand edit merges but does
not build :-P
Thank you :-)
Tomek
[1]
https://www.asus.com/motherboards-components/motherboards/tuf-gaming/tuf-gaming-z890-pro-wifi/
[2]
https://www.asus.com/motherboards-components/motherboards/tuf-gaming/tuf-gaming-z890-pro-wifi/helpdesk_manual?model2Name=TUF-GAMING-Z890-PRO-WIFI
--
You are receiving this mail because:
You are the assignee for the bug.
lmpx.com only provides a reader for public news (NNTP) servers. It is not
affiliated with the servers or forums shown here and is not responsible for
the content of articles, which is written by their respective authors.