Re: Upgrade from squid 6.14 to 7.3 fails

Hello

I'm really sorry for the inconvenience, but this upgrade has already had a
few problems:
https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=292070
https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=292098

The failure you encountered is because of the STACKTRACES option turned ON.
You can turn it off to make it build for now.

I'll take a look at it a bit later.

On Fri, Jan 2, 2026 at 12:48 PM Xavier Humbert <[email protected]> wrote:

> Hi,
>
> Now that squid 7 is out, I tried to update my system, but if fails on
> FreeBSD numenor.groumpf.org 14.3-STABLE FreeBSD 14.3-STABLE
> stable/14-f9d671f726ac GENERIC amd64
>
> c++ -std=c++17 -DHAVE_CONFIG_H
> -DDEFAULT_CONFIG_FILE=\"/usr/local/etc/squid/squid.conf\"
> -DDEFAULT_SQUID_DATA_DIR=\"/usr/local/etc/squid\"
> -DDEFAULT_SQUID_CONFIG_DIR=\"/usr/local/etc/squid\"   -I.. -I../include
> -I../lib -I../src -I../include -I/usr/local/include -I../libltdl
> -I../src -I../libltdl -I/usr/local/include -I/usr/local/include
> -I/usr/local/include -I/usr/local/include -I/usr/local/include -isystem
> /usr/local/include -Wall -Wextra -Wno-unused-private-field
> -Wno-implicit-fallthrough -Wpointer-arith -Wwrite-strings -Wcomments
> -Wshadow -Wmissing-declarations -Woverloaded-virtual  -D_REENTRANT
> -I/usr/local/include -pipe -g -march=core2 -g -DLDAP_DEPRECATED -g
> -fstack-protector-strong -isystem /usr/local/include
> -fno-strict-aliasing -g -isystem /usr/local/include -I/usr/local/include
> -MT tools.o -MD -MP -MF $depbase.Tpo -c -o tools.o tools.cc &&\
> mv -f $depbase.Tpo $depbase.Po
> tools.cc:403:21: error: use of undeclared identifier 'debug_log'
>    403 |             fprintf(debug_log, "Failed to trace own stack: "
>        |                     ^
> tools.cc:408:21: error: use of undeclared identifier 'debug_log'
>    408 |             fprintf(debug_log, "Failed to trace own stack: "
>        |                     ^
> tools.cc:413:10: error: use of undeclared identifier 'debug_log'
>    413 |         fprintf(debug_log, "Backtrace follows (deepest frame
> first):\n");
>        |                 ^
> tools.cc:423:14: error: use of undeclared identifier 'debug_log'
>    423 |             fprintf(debug_log, "#%zd: %s + 0x%zx, ip = 0x%zx,
> sp = 0x%zx\n",
>        |                     ^
> tools.cc:426:10: error: use of undeclared identifier 'debug_log'
>    426 |         fprintf(debug_log, "Use addr2line of similar to
> translate offsets to line information.\n");
>        |                 ^
> 5 errors generated.
>
> I tried with or without the DEBUG flag in make config, no change
>
> Output of make "showconfig"
>
> ===> The following configuration options are available for squid-7.3:
>       ARP_ACL=on: ARP/MAC/EUI based authentification
>       CACHE_DIGESTS=on: Use cache digests
>       DEBUG=off: Build with extended debugging support
>       DELAY_POOLS=on: Delay pools (bandwidth limiting)
>       DOCS=on: Build and/or install documentation
>       ECAP=on: Loadable content adaptation modules
>       EXAMPLES=on: Build and/or install examples
>       FOLLOW_XFF=on: Support for the X-Following-For header
>       FS_AUFS=on: AUFS (threaded-io) support
>       FS_DISKD=on: DISKD storage engine controlled by separate service
>       FS_ROCK=on: ROCK storage engine
>       HTCP=on: HTCP support
>       ICAP=on: the ICAP client
>       ICMP=on: ICMP pinging and network measurement
>       IPV6=on: IPv6 protocol support
>       KQUEUE=on: Kqueue(2) support
>       LARGEFILE=on: Support large (>2GB) cache and log files
>       LAX_HTTP=on: Do not enforce strict HTTP compliance
>       NETTLE=on: Nettle MD5 algorithm support
>       SNMP=on: SNMP support
>       SSL=on: SSL gatewaying support
>       SSL_CRTD=on: Use ssl_crtd to handle SSL cert requests
>       STACKTRACES=on: Enable automatic backtraces on fatal errors
>       TDB=off: TrivialDB support required for session and time quota
> external helpers
>       VIA_DB=on: Forward/Via database
>       WCCP=on: Web Cache Coordination Protocol
>       WCCPV2=on: Web Cache Coordination Protocol v2
> ====> Authentication helpers
>       AUTH_LDAP=on: Install LDAP authentication helpers
>       AUTH_NIS=off: Install NIS/YP authentication helpers
>       AUTH_SASL=off: Install SASL authentication helpers
>       AUTH_SMB=off: Install SMB auth. helpers (req. Samba)
>       AUTH_SQL=on: Install SQL based auth
> ====> GSSAPI Security API support: you have to select exactly one of them
>       GSSAPI_BASE=off: GSSAPI support via base system (needs Kerberos)
>       GSSAPI_HEIMDAL=off: GSSAPI support via security/heimdal
>       GSSAPI_MIT=off: GSSAPI support via security/krb5
>       GSSAPI_NONE=on: Disable GSSAPI support
> ====> Options available for the radio FW: you can only select none or
> one of them
>       TP_IPF=off: Transparent proxying with IPFilter
>       TP_IPFW=off: Transparent proxying with IPFW
>       TP_PF=on: Transparent proxying with PF
>
> Regards,
>
> Xavier
>
> --
> Xavier HUMBERT - Unix/Win/MacOSX Sysadmin/Network Engineer
> https://www.amdh.fr
>
>
>