Re: kern/47451: 5.0 GENERIC(sysinstall CD) locks during boot onProliant ML530
Sergei Kolobov <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.quality-assurance |
|---|---|
| Message-ID | <[email protected]> |
The following reply was made to PR kern/47451; it has been noted by GNATS. From: Sergei Kolobov <[email protected]> To: John Baldwin <[email protected]>, [email protected] Cc: Kevin Day <[email protected]> Subject: Re: kern/47451: 5.0 GENERIC(sysinstall CD) locks during boot on Proliant ML530 Date: Wed, 18 Aug 2004 20:01:50 +0400 John, I am experiencing the same problem on Compaq Proliant hardware. Please find below a boot log for 5.2.1-RELEASE install CD. My hardware configuration is: Compaq Proliant 1600 server BIOS P08 (04/21/1999) Pentium II 400 MHz 256M RAM SMART-2DH RAID controller (rev.C, firmware ver.4.50, 16M cache) When booting normally (with vidconsole), it fails like this: Mounting root from ufs:/dev/md0 /stand/sysinstall running as init on serial console panic: unknown/reserved trap cpuid = 0 .... This is a log I captured via serial console. It got slightly further - up to the main sysinstall screen, but locked after that - no selection can be made. I would appreciate any help resolving this issue. I have several similar servers and wanted to install 5.2.1 on all of them. Please let me know if you need any additional info. Thanks, Sergei ======[start of boot log]========== Copyright (c) 1992-2004 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.2.1-RELEASE #0: Mon Feb 23 20:45:55 GMT 2004 [email protected]:/usr/obj/usr/src/sys/GENERIC Preloaded elf kernel "/boot/kernel/kernel" at 0xc0e1b000. Preloaded mfs_root "/boot/mfsroot" at 0xc0e1b21c. MPTable: <COMPAQ PROLIANT > Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Pentium II/Pentium II Xeon/Celeron (399.09-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x652 Stepping = 2 Features=0x183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR> real memory = 268435456 (256 MB) avail memory = 247037952 (235 MB) ioapic0: Changing APIC ID to 8 ioapic0: Assuming intbase of 0 ioapic0 <Version 1.1> irqs 0-34 on motherboard Pentium Pro MTRR support enabled npx0: [FAST] stray irq13 npx0: <math processor> on motherboard npx0: INT 16 interface pcibios: BIOS version 2.10 pcib0: <MPTable Host-PCI bridge> at pcibus 0 on motherboard pci0: <PCI bus> on pcib0 pci0: <display, VGA> at device 11.0 (no driver attached) pcib1: <MPTable PCI-PCI bridge> at device 13.0 on pci0 pci1: <PCI bus> on pcib1 pcib1: slot 7 INTA routed to irq 30 pcib1: slot 9 INTA routed to irq 23 pcib1: slot 9 INTB routed to irq 22 tl0: <Compaq Netelligent 10/100 Proliant> port 0x2800-0x280f mem 0xc6efddf0-0xc6efddff irq 30 at device 7.0 on pci1 tl0: Ethernet address: 00:08:c7:33:47:21 miibus0: <MII bus> on tl0 nsphy0: <DP83840 10/100 media interface> on miibus0 nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto tlphy0: <ThunderLAN 10baseT media interface> on miibus0 tlphy0: 10base2/BNC, 10base5/AUI sym0: <875> port 0x2000-0x20ff mem 0xc6eff000-0xc6efffff,0xc6efdf00-0xc6efdfff irq 23 at device 9.0 on pci1 sym0: No NVRAM, ID 7, Fast-20, SE, parity checking sym1: <875> port 0x2400-0x24ff mem 0xc6efe000-0xc6efefff,0xc6efde00-0xc6efdeff irq 22 at device 9.1 on pci1 sym1: No NVRAM, ID 7, Fast-20, SE, parity checking pci0: <base peripheral> at device 14.0 (no driver attached) pcib2: <PCI-PCI bridge> at device 15.0 on pci0 pci2: <PCI bus> on pcib2 pcib0: slot 15 INTA routed to irq 19 pcib2: slot 0 INTA is routed to irq 19 ida0: <Compaq SMART-2/P array controller> port 0x3000-0x30ff mem 0xb8000000-0xbfffffff,0xc6ffff00-0xc6ffffff irq 19 at device 0.0 on pci2 ida0: drives=1 firm_rev=4.50 idad0: <Compaq Logical Drive> on ida0 idad0: 17351MB (35536800 sectors), blocksize=512 GEOM: create disk idad0 dp=0xc30f6608 isab0: <PCI-ISA bridge> at device 20.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel PIIX4 UDMA33 controller> port 0xf100-0xf10f at device 20.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata0: [MPSAFE] ata1: at 0x170 irq 15 on atapci0 ata1: [MPSAFE] uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0-0x1f at device 20.2 on pci0 pcib0: unable to route slot 20 INTD uhci0: Could not allocate irq device_probe_and_attach: uhci0 attach returned 6 piix0: <PIIX Timecounter> port 0xf040-0xf04f at device 20.3 on pci0 Timecounter "PIIX" frequency 3579545 Hz quality 0 eisa0: <EISA bus> on motherboard mainboard0: <CPQ0689 (System Board)> on eisa0 slot 0 orm0: <Option ROMs> at iomem 0xee000-0xeffff,0xe8000-0xedfff,0xc8000-0xcbfff,0xc0000-0xc7fff on isa0 pmtimer0 on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model NetMouse/NetScroll Optical, device ID 0 fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 ppc0: <Parallel port> at port 0x3bc-0x3c3 irq 7 on isa0 ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x100> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A, console sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounter "TSC" frequency 399086643 Hz quality 800 Timecounters tick every 10.000 msec md0: Preloaded image </boot/mfsroot> 4423680 bytes at 0xc09e16d8 acd0: CDROM <Compaq CRD-8241B> at ata0-master PIO4 Waiting 15 seconds for SCSI devices to settle sa0 at sym0 bus 0 target 6 lun 0 sa0: <HP C1537A L708> Removable Sequential Access SCSI-2 device sa0: 10.000MB/s transfers (10.000MHz, offset 16) Mounting root from ufs:/dev/md0 /stand/sysinstall running as init on serial console These are the predefined terminal types available to sysinstall when running stand-alone. Please choose the closest match for your particular terminal. 1 ...................... Standard ANSI terminal. 2 ...................... VT100 or compatible terminal. 3 ...................... FreeBSD system console (color). 4 ...................... FreeBSD system console (monochrome). 5 ...................... xterm terminal emulator. Your choice: (1-5) 1 module_register: module pci/txp already exists! Module pci/txp failed to register: 17 uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0-0x1f at device 20.2 on pci0 pcib0: unable to route slot 20 INTD uhci0: Could not allocate irq device_probe_and_attach: uhci0 attach returned 6 interface cd9660.1 already present in the KLD 'kernel'! interface sysvmsg.1 already present in the KLD 'kernel'! module_register: module pccard/xe already exists! Module pccard/xe failed to register: 17 module_register: module pci/pcn already exists! Module pci/pcn failed to register: 17 module_register: module pcn/miibus already exists! Module pcn/miibus failed to register: 17 uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0-0x1f at device 20.2 on pci0 pcib0: unable to route slot 20 INTD uhci0: Could not allocate irq device_probe_and_attach: uhci0 attach returned 6 module_register: module pci/vr already exists! Module pci/vr failed to register: 17 module_register: module vr/miibus already exists! Module vr/miibus failed to register: 17 uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0-0x1f at device 20.2 on pci0 pcib0: unable to route slot 20 INTD uhci0: Could not allocate irq device_probe_and_attach: uhci0 attach returned 6 module_register: module pci/ste already exists! Module pci/ste failed to register: 17 module_register: module ste/miibus already exists! Module ste/miibus failed to register: 17 uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0-0x1f at device 20.2 on pci0 pcib0: unable to route slot 20 INTD uhci0: Could not allocate irq device_probe_and_attach: uhci0 attach returned 6 module_register: module if_tun already exists! Module if_tun failed to register: 17 can't re-use a leaf (if_tun_debug)! module_register: module uhub/cue already exists! Module uhub/cue failed to register: 17 module_register: module cardbus/xl already exists! Module cardbus/xl failed to register: 17 module_register: module pci/xl already exists! Module pci/xl failed to register: 17 module_register: module xl/miibus already exists! Module xl/miibus failed to register: 17 uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0-0x1f at device 20.2 on pci0 pcib0: unable to route slot 20 INTD uhci0: Could not allocate irq device_probe_and_attach: uhci0 attach returned 6 module_register: module pccard/ed already exists! Module pccard/ed failed to register: 17 module_register: module ed/miibus already exists! Module ed/miibus failed to register: 17 module_register: module pci/ed already exists! Module pci/ed failed to register: 17 module_register: module isa/ed already exists! Module isa/ed failed to register: 17 uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0-0x1f at device 20.2 on pci0 pcib0: unable to route slot 20 INTD uhci0: Could not allocate irq device_probe_and_attach: uhci0 attach returned 6 module_register: module pci/bge already exists! Module pci/bge failed to register: 17 module_register: module bge/miibus already exists! Module bge/miibus failed to register: 17 uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0-0x1f at device 20.2 on pci0 pcib0: unable to route slot 20 INTD uhci0: Could not allocate irq device_probe_and_attach: uhci0 attach returned 6 module_register: module pci/re already exists! Module pci/re failed to register: 17 module_register: module cardbus/re already exists! Module cardbus/re failed to register: 17 module_register: module re/miibus already exists! Module re/miibus failed to register: 17 uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0-0x1f at device 20.2 on pci0 pcib0: unable to route slot 20 INTD uhci0: Could not allocate irq device_probe_and_attach: uhci0 attach returned 6 module_register: module pci/wb already exists! Module pci/wb failed to register: 17 module_register: module wb/miibus already exists! Module wb/miibus failed to register: 17 uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0-0x1f at device 20.2 on pci0 pcib0: unable to route slot 20 INTD uhci0: Could not allocate irq device_probe_and_attach: uhci0 attach returned 6 module_register: module pci/rl already exists! Module pci/rl failed to register: 17 module_register: module cardbus/rl already exists! Module cardbus/rl failed to register: 17 module_register: module rl/miibus already exists! Module rl/miibus failed to register: 17 uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0-0x1f at device 20.2 on pci0 pcib0: unable to route slot 20 INTD uhci0: Could not allocate irq device_probe_and_attach: uhci0 attach returned 6 module_register: module pci/sis already exists! Module pci/sis failed to register: 17 module_register: module sis/miibus already exists! Module sis/miibus failed to register: 17 uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0-0x1f at device 20.2 on pci0 pcib0: unable to route slot 20 INTD uhci0: Could not allocate irq device_probe_and_attach: uhci0 attach returned 6 module_register: module cardbus/dc already exists! Module cardbus/dc failed to register: 17 module_register: module pci/dc already exists! Module pci/dc failed to register: 17 module_register: module dc/miibus already exists! Module dc/miibus failed to register: 17 can't re-use a leaf (dc_quick)! uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0-0x1f at device 20.2 on pci0 pcib0: unable to route slot 20 INTD uhci0: Could not allocate irq device_probe_and_attach: uhci0 attach returned 6 interface sysvshm.1 already present in the KLD 'kernel'! module_register: module pci/bfe already exists! Module pci/bfe failed to register: 17 module_register: module bfe/miibus already exists! Module bfe/miibus failed to register: 17 uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0-0x1f at device 20.2 on pci0 pcib0: unable to route slot 20 INTD uhci0: Could not allocate irq device_probe_and_attach: uhci0 attach returned 6 module_register: module uhub/aue already exists! Module uhub/aue failed to register: 17 module_register: module aue/miibus already exists! Module aue/miibus failed to register: 17 interface miibus.1 already present in the KLD 'kernel'! module_register: module pci/lnc already exists! Module pci/lnc failed to register: 17 module_register: module isa/lnc already exists! Module isa/lnc failed to register: 17 uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0-0x1f at device 20.2 on pci0 pcib0: unable to route slot 20 INTD uhci0: Could not allocate irq device_probe_and_attach: uhci0 attach returned 6 interface sysvsem.1 already present in the KLD 'kernel'! module_register: module pccard/fe already exists! Module pccard/fe failed to register: 17 module_register: module isa/fe already exists! Module isa/fe failed to register: 17 module_register: module pci/fxp already exists! Module pci/fxp failed to register: 17 module_register: module cardbus/fxp already exists! Module cardbus/fxp failed to register: 17 module_register: module fxp/miibus already exists! Module fxp/miibus failed to register: 17 can't re-use a leaf (fxp_rnr)! can't re-use a leaf (fxp_noflow)! uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0-0x1f at device 20.2 on pci0 pcib0: unable to route slot 20 INTD uhci0: Could not allocate irq device_probe_and_attach: uhci0 attach returned 6 module_register: module uhub/kue already exists! Module uhub/kue failed to register: 17 module_register: module pci/sf already exists! Module pci/sf failed to register: 17 module_register: module sf/miibus already exists! Module sf/miibus failed to register: 17 uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0-0x1f at device 20.2 on pci0 pcib0: unable to route slot 20 INTD uhci0: Could not allocate irq device_probe_and_attach: uhci0 attach returned 6 [;H[2J [11;11H+---------------------------------------------------------+[12;11H| Probing devices, please wait (this can take a while)... |[13;11H+---------------------------------------------------------+[A[11;11H[K [K [K[24;80H[H +------------------------ sysinstall Main Menu -------------------------+ | Welcome to the FreeBSD installation and configuration tool. Please | | select one of the options below by using the arrow keys or typing the | | first character of the option name you're interested in. Invoke an | | option with [SPACE] or [ENTER]. To exit, use [TAB] to move to Exit. | | +-------------------------------------------------------------------+ | | | Usage Quick start - How to use this menu system | | | | Standard Begin a standard installation (recommended) | | | | Express Begin a quick installation (for experts) | | | | Custom Begin a custom installation (for experts) | | | | Configure Do post-install configuration of FreeBSD | | | | Doc Installation instructions, README, etc. | | | | Keymap Select keyboard type | | | | Options View/Set various installation options | | | | Fixit Repair mode with CDROM/DVD/floppy or start shell | | | | Upgrade Upgrade an existing system | | | | Load Config Load default install configuration | | | | Index Glossary of functions | | | +-------------------------------------------------------------------+ | +-----------------------------------------------------------------------+ | [Select] X Exit Install | +------------------[ Press F1 for Installation Guide ]------------------+[22;30H ======[end of boot log]========== _______________________________________________ [email protected] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-qa To unsubscribe, send any mail to "[email protected]"