Re: kern/47451: 5.0 GENERIC(sysinstall CD) locks during boot onProliant ML530

The following reply was made to PR kern/47451; it has been noted by GNATS.

From: John Baldwin <[email protected]>
To: [email protected]
Cc: Sergei Kolobov <[email protected]>,
	[email protected]
Subject: Re: kern/47451: 5.0 GENERIC(sysinstall CD) locks during boot onProliant ML530
Date: Fri, 20 Aug 2004 10:48:53 -0400

 On Friday 20 August 2004 02:20 am, Sergei Kolobov wrote:
 > On 2004-08-18 at 15:33 -0400, John Baldwin wrote:
 > > On Wednesday 18 August 2004 12:10 pm, Sergei Kolobov wrote:
 > > >  uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0-0x1f at device
 > > > 20.2 on pci0 pcib0: unable to route slot 20 INTD
 > > >  uhci0: Could not allocate irq
 > > >  device_probe_and_attach: uhci0 attach returned 6
 > >
 > > This might be indicative of the problem.  Can you try the following
 > > tweaks to the BIOS setup:
 > >
 > > 1) Ensure that PnP OS is set to "no"
 >
 > The closest equivalent I could find for this is "Primary Operating
 > System: Other". Remember - this is Compaq hardware, and they have
 > nothing even distantly resembling "normal" Award/Phoenix BIOS.
 > Instead, you have to use that (EISA) System Configuration Utility
 > from the System Partition or SmartStart CD-ROM.
 
 You might try some of the different operating system settings there and see if 
 they help.  I would try them all to be honest and see if any of them allow 
 the install CD to boot ok.
 
 > > 3) Enable USB in the BIOS if it is disabled.
 >
 > There no USB-related option at all. In fact, there are *NO* USB ports
 > in this server (it is circa '98-99). Isn't it funny the kernel found
 > some USB controller, is it?
 
 Hmm, it's probably in the chipset but the manufacturer might have chosen not 
 to install any USB ports for some reason.
 
 > Believe it or not, but I was finally able to install 5.2.1 on this
 > hardware. After you mentioned that USB might be causing this,
 > I have compiled a custom kernel on another 5.x machine (which happened
 > to be my laptop running a recent -CURRENT) and put it on the kernel
 > floppy, replacing GENERIC in kernel.gz. Voila - it booted without
 > a problem, and I was able to use sysinstall on regular console (as
 > opposed to serial console I had to use to capture the previous boot
 > log).
 >
 > What I still do not understand - why then it would boot the same GENERIC
 > kernel without a problem when the system was already installed?
 > What is the difference between the boot process for install CD/floppy
 > and the installed system?
 
 The 5.2.1 install floppies don't use GENERIC but a stripped down kernel.  The 
 install CD should use GENERIC though if you boot off of the CD and don't use 
 any floppies.
 
 -- 
 John Baldwin <[email protected]>  <><  http://www.FreeBSD.org/~jhb/
 "Power Users Use the Power to Serve"  =  http://www.FreeBSD.org
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-qa
To unsubscribe, send any mail to "[email protected]"