no smp with compaq proliant ml570
Stefan Hauser <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.smp |
|---|---|
| Message-ID | <[email protected]> |
hello
i tried freebsd 6.1-rc on a compaq proliant ml 570 with 4 cpu. but freebsd
doesnt want to do smp there. tried 7-current to, no difference.
kernel(s) do have option SMP in the config file. thats not the problem.
mptable shows 4 cpus, but also an 'mptable out of order'. and i dont see
'APIC' in the feature list of the cpu.
anyone has any hints how to get smp going on this machine ?
following is the verbose boot and mptable output.
etienne
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.1-RC #0: Sat Apr 22 21:18:36 CEST 2006
[email protected]:/usr/obj/usr/src/sys/PROLIANT
Preloaded elf kernel "/boot/kernel/kernel" at 0xc09d8000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc09d8188.
Calibrating clock(s) ... i8254 clock: 1193119 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 701599194 Hz
CPU: Intel Pentium III Xeon (701.60-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6a1 Stepping = 1
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 4127178752 (3935 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c28000 - 0x00000000f1a93fff, 4041654272 bytes (986732 pages)
avail memory = 4041433088 (3854 MB)
bios32: Found BIOS32 Service Directory header at 0xc00ffee0
bios32: Entry = 0xf0000 (c00f0000) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0x84
Other BIOS signatures found:
wlan: <802.11 Link Layer>
mem: <memory>
Pentium Pro MTRR support enabled
nfslock: pseudo-device
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
io: <I/O>
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <COMPAQ YORKTOWN> on motherboard
acpi0: [MPSAFE]
acpi0: Power Button (fixed)
atpic: Programming IRQ9 as level/low
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=00081166)
pcibios: BIOS version 2.10
AcpiOsDerivePciId: bus 0 dev 0 func 1
unknown: I/O range not supported
AcpiOsDerivePciId: bus 0 dev 0 func 2
AcpiOsDerivePciId: bus 0 dev 0 func 3
pci_link1: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 3 N 0 15
pci_link1: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link1: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link2: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link2: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link2: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link3: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 10 N 0 15
pci_link3: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link3: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link4: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link4: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link4: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link5: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link5: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link5: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link6: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link6: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link6: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link7: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 5 N 0 15
pci_link7: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link7: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link8: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link8: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link8: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link9: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link9: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link9: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link10: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link10: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link10: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link11: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link11: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link11: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link12: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link12: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link12: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link13: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 5 N 0 15
pci_link13: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link13: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link14: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 15
pci_link14: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link14: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link15: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 15 N 0 15
pci_link15: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 15 N 0 15
pci_link15: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link16: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link16: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
pci_link16: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 15
ACPI timer: 1/0 1/0 1/0 1/0 1/0 1/0 1/0 1/0 1/0 1/0 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x240-0x243 on acpi0
cpu0: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> on acpi0
pci_link0: apparently invalid index 0
ACPI: Found matching pin for 0.4.INTA at func 0: 11
pci_link14: BIOS IRQ 11 for 0.4.INTA is invalid
ACPI: Found matching pin for 0.4.INTB at func 1: 5
pci_link13: BIOS IRQ 5 for 0.4.INTB is invalid
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x1166, dev=0x0008, revid=0x23
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1166, dev=0x0008, revid=0x01
bus=0, slot=0, func=1
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0147, statreg=0x2200, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1166, dev=0x0006, revid=0x01
bus=0, slot=0, func=2
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0142, statreg=0x2200, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1166, dev=0x0006, revid=0x01
bus=0, slot=0, func=3
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0142, statreg=0x2200, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x0e11, dev=0xa0f0, revid=0x00
bus=0, slot=3, func=0
class=08-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0143, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
map[10]: type 4, range 32, base 00001800, size 8, enabled
map[14]: type 1, range 32, base f7af0000, size 8, enabled
found-> vendor=0x1000, dev=0x000a, revid=0x02
bus=0, slot=4, func=0
class=01-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0157, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0xff (7650 ns), mingnt=0x1e (7500 ns), maxlat=0x08 (2000 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 00002000, size 8, enabled
map[14]: type 1, range 32, base f7ae0000, size 10, enabled
map[18]: type 1, range 32, base f7ad0000, size 12, enabled
pcib0: matched entry for 0.4.INTA (src \\_SB_.INAD:0)
pci_link14: Picked IRQ 9 with weight 0
pcib0: slot 4 INTA routed to irq 9 via \\_SB_.INAD
found-> vendor=0x1000, dev=0x000a, revid=0x02
bus=0, slot=4, func=1
class=01-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0157, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0xff (7650 ns), mingnt=0x1e (7500 ns), maxlat=0x08 (2000 ns)
intpin=b, irq=5
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 00002400, size 8, enabled
map[14]: type 1, range 32, base f7ac0000, size 10, enabled
map[18]: type 1, range 32, base f7ab0000, size 12, enabled
pcib0: matched entry for 0.4.INTB (src \\_SB_.INAC:0)
pci_link13: Picked IRQ 9 with weight 1
pcib0: slot 4 INTB routed to irq 9 via \\_SB_.INAC
found-> vendor=0x1002, dev=0x4756, revid=0x7a
bus=0, slot=5, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0087, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
powerspec 1 supports D0 D3 current D0
map[10]: type 3, range 32, base f6000000, size 24, enabled
map[14]: type 4, range 32, base 00002800, size 8, enabled
map[18]: type 1, range 32, base f7aa0000, size 12, enabled
found-> vendor=0x1166, dev=0x0200, revid=0x51
bus=0, slot=15, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[90]: type 4, range 32, base 00000000, size 4, enabled
found-> vendor=0x1166, dev=0x0211, revid=0x00
bus=0, slot=15, func=1
class=01-01-8a, hdrtype=0x00, mfdev=1
cmdreg=0x0145, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 00002c00, size 4, enabled
pci0: <base peripheral> at device 3.0 (no driver attached)
sym0: <1510d> port 0x2000-0x20ff mem 0xf7ae0000-0xf7ae03ff,0xf7ad0000-0xf7ad0fff irq 9 at device 4.0 on pci0
sym0: Reserved 0x400 bytes for rid 0x14 type 3 at 0xf7ae0000
sym0: Reserved 0x1000 bytes for rid 0x18 type 3 at 0xf7ad0000
sym0: chip clock is 40401KHz
sym0: No NVRAM, ID 7, Fast-40, LVD, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: [GIANT-LOCKED]
sym1: <1510d> port 0x2400-0x24ff mem 0xf7ac0000-0xf7ac03ff,0xf7ab0000-0xf7ab0fff irq 9 at device 4.1 on pci0
sym1: Reserved 0x400 bytes for rid 0x14 type 3 at 0xf7ac0000
sym1: Reserved 0x1000 bytes for rid 0x18 type 3 at 0xf7ab0000
sym1: chip clock is 40401KHz
sym1: No NVRAM, ID 7, Fast-40, LVD, parity checking
sym1: open drain IRQ line driver, using on-chip SRAM
sym1: using LOAD/STORE-based firmware.
sym1: [GIANT-LOCKED]
pci0: <display, VGA> at device 5.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <ServerWorks ROSB4 UDMA33 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x2c00-0x2c0f at device 15.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x2c00
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=01
ata0: stat0=0x10 err=0x01 lsb=0x14 msb=0xeb
ata0: stat1=0x00 err=0x01 lsb=0x7f msb=0x7f
ata0: reset tp2 stat0=10 stat1=00 devices=0x4<ATAPI_MASTER>
ata0: [MPSAFE]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=00 ostat0=ff ostat1=ff
ata1: [MPSAFE]
pcib1: <ACPI Host-PCI bridge> on acpi0
ACPI: Found matching pin for 2.6.INTA at func 0: 3
pci_link1: BIOS IRQ 3 for 2.6.INTA is invalid
ACPI: Found matching pin for 2.8.INTA at func 0: 10
pci_link3: BIOS IRQ 10 for 2.8.INTA is invalid
ACPI: Found matching pin for 2.5.INTA at func 0: 15
pci2: <ACPI PCI bus> on pcib1
pci2: physical bus=2
found-> vendor=0x0e11, dev=0xa0f7, revid=0x12
bus=2, slot=5, func=0
class=08-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0142, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=15
MSI supports 1 message, 64 bit
map[10]: type 1, range 32, base f7df0000, size 8, enabled
pcib1: matched entry for 2.5.INTA (src \\_SB_.INAE:0)
pcib1: slot 5 INTA routed to irq 15 via \\_SB_.INAE
found-> vendor=0x8086, dev=0x1229, revid=0x08
bus=2, slot=6, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0157, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns)
intpin=a, irq=3
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base f7de0000, size 12, enabled
map[14]: type 4, range 32, base 00003000, size 6, enabled
map[18]: type 1, range 32, base f7c00000, size 20, enabled
pcib1: matched entry for 2.6.INTA (src \\_SB_.INA0:0)
pci_link1: Picked IRQ 15 with weight 1
pcib1: slot 6 INTA routed to irq 15 via \\_SB_.INA0
found-> vendor=0x8086, dev=0x1000, revid=0x03
bus=2, slot=8, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0156, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 1 supports D0 D3 current D0
map[10]: type 1, range 32, base f7be0000, size 17, enabled
pcib1: matched entry for 2.8.INTA (src \\_SB_.INA2:0)
pci_link3: Picked IRQ 9 with weight 2
pcib1: slot 8 INTA routed to irq 9 via \\_SB_.INA2
pci2: <base peripheral, PCI hot-plug controller> at device 5.0 (no driver attached)
fxp0: <Intel 82559 Pro/100 Ethernet> port 0x3000-0x303f mem 0xf7de0000-0xf7de0fff,0xf7c00000-0xf7cfffff irq 15 at device 6.0 on pci2
fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xf7de0000
fxp0: using memory space register mapping
fxp0: PCI IDs: 8086 1229 0e11 b144 0008
fxp0: Dynamic Standby mode is disabled
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: bpf attached
fxp0: Ethernet address: 00:50:8b:bb:b1:74
fxp0: [MPSAFE]
em0: <Intel(R) PRO/1000 Network Connection Version - 3.2.18> mem 0xf7be0000-0xf7bfffff irq 9 at device 8.0 on pci2
em0: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xf7be0000
em0: [MPSAFE]
em0: bpf attached
em0: Ethernet address: 00:08:c7:86:1d:f6
em0: Speed:N/A Duplex:N/A
pcib2: <ACPI Host-PCI bridge> on acpi0
ACPI: Found matching pin for 7.6.INTA at func 0: 5
pci_link7: BIOS IRQ 5 for 7.6.INTA is invalid
ACPI: Found matching pin for 7.5.INTA at func 0: 15
pci7: <ACPI PCI bus> on pcib2
pci7: physical bus=7
found-> vendor=0x0e11, dev=0xa0f7, revid=0x12
bus=7, slot=5, func=0
class=08-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0142, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=15
MSI supports 1 message, 64 bit
map[10]: type 1, range 32, base f7ff0000, size 8, enabled
pcib2: matched entry for 7.5.INTA (src \\_SB_.INAE:0)
pcib2: slot 5 INTA routed to irq 15 via \\_SB_.INAE
found-> vendor=0x0e11, dev=0xb060, revid=0x02
bus=7, slot=6, func=0
class=01-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0157, statreg=0x0230, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=5
powerspec 2 supports D0 D1 D3 current D0
map[10]: type 1, range 32, base f7f80000, size 18, enabled
map[14]: type 1, range 32, base f7e00000, size 20, enabled
map[20]: type 4, range 32, base 00004000, size 8, enabled
pcib2: matched entry for 7.6.INTA (src \\_SB_.INA6:0)
pci_link7: Picked IRQ 15 with weight 4
pcib2: slot 6 INTA routed to irq 15 via \\_SB_.INA6
pci7: <base peripheral, PCI hot-plug controller> at device 5.0 (no driver attached)
ciss0: <Compaq Smart Array 5300> port 0x4000-0x40ff mem 0xf7f80000-0xf7fbffff,0xf7e00000-0xf7efffff irq 15 at device 6.0 on pci7
ciss0: Reserved 0x40000 bytes for rid 0x10 type 3 at 0xf7f80000
ciss0: Reserved 0x100000 bytes for rid 0x14 type 3 at 0xf7e00000
ciss0: [GIANT-LOCKED]
ciss0: using 256 of 1024 available commands
ciss0: firmware 1.62
ciss0: 2 SCSI channels
ciss0: signature 'CISS'
ciss0: valence 1
ciss0: supported I/O methods 0xe<simple,performant,MEMQ>
ciss0: active I/O method 0x3<simple>
ciss0: 4G page base 0x00000000
ciss0: interrupt coalesce delay 1000us
ciss0: interrupt coalesce count 0
ciss0: max outstanding commands 1024
ciss0: bus types 0x2<ultra3>
ciss0: server name ''
ciss0: heartbeat 0x20000071
ciss0: 8 physical devices
ciss0: 2 logical drives
ciss0: logical drive (b0t0): RAID 1, 8192MB online
ciss0: logical drive (b0t1): RAID 5, 51712MB online
acpi_tz0: <Thermal Zone> on acpi0
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x1d0000
atkbd0: [GIANT-LOCKED]
psm0: current command byte:0065
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model Generic PS/2 mouse, device ID 0-00, 3 buttons
psm0: config:00000000, flags:00000008, packet size:3
psm0: syncmask:c0, syncbits:00
ppc0: using extended I/O port range
ppc0: SPP
ppc0: <Standard parallel printer port> port 0x378-0x37f,0x778-0x77d irq 7 drq 0 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
fdc0: <floppy drive controller> port 0x3f2-0x3f5 irq 6 drq 2 on acpi0
fdc0: ic_type 90 part_id 73
fdc0: [MPSAFE]
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: irq maps: 0x1 0x11 0x1 0x1
sio0: <Standard PC COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A, console
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0x1 0x1 0x1 0x1
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0x1 0x1 0x1 0x1
sio1: probe failed test(s): 0 1 2 4 6 7 9
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sio: sio0 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
ahc_isa_probe 2: ioport 0x2c00 alloc failed
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc97ff,0xc9800-0xcd7ff,0xe8000-0xedfff,0xee000-0xeffff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0x1 0x1 0x1 0x1
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
Reducing kern.maxvnodes 253078 -> 100000
procfs registered
Timecounter "TSC" frequency 701599194 Hz quality 800
Timecounters tick every 1.000 msec
lo0: bpf attached
ata0-master: pio=PIO4 wdma=WDMA2 udma=UNSUPPORTED cable=40 wire
acd0: setting PIO4 on ROSB4 chip
acd0: <COMPAQ SC-140S/SE04> CDROM drive at ata0 as master
acd0: read 171KB/s (6875KB/s), 128KB buffer, PIO4
acd0: Reads: CDR, CDRW, CDDA stream, packet
acd0: Writes:
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
Waiting 2 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
(noperiph:sym1:0:-1:-1): SCSI BUS reset delivered.
(probe45:ata0:0:0:0): error 22
(probe45:ata0:0:0:0): Unretryable Error
(probe45:ata0:0:0:0): error 6
(probe45:ata0:0:0:0): Unretryable Error
ciss0: command status 0x1 (target status) scsi status 0x2
ciss0: command status 0x1 (target status) scsi status 0x2
(probe0:ciss0:0:0:0): error 22
(probe0:ciss0:0:0:0): Unretryable Error
(probe1:ciss0:0:1:0): error 22
(probe1:ciss0:0:1:0): Unretryable Error
ciss0: command status 0x1 (target status) scsi status 0x2
ciss0: command status 0x1 (target status) scsi status 0x2
(probe0:ciss0:0:0:0): error 22
(probe0:ciss0:0:0:0): Unretryable Error
(probe1:ciss0:0:1:0): error 22
(probe1:ciss0:0:1:0): Unretryable Error
(probe45:ata0:0:0:0): error 22
(probe45:ata0:0:0:0): Unretryable Error
ciss0: command status 0x1 (target status) scsi status 0x2
(probe0:ciss0:0:0:0): error 22
(probe0:ciss0:0:0:0): Unretryable Error
ciss0: command status 0x1 (target status) scsi status 0x2
ciss0: command status 0x1 (target status) scsi status 0x2
(probe1:ciss0:0:1:0): error 22
(probe1:ciss0:0:1:0): Unretryable Error
(probe0:ciss0:0:0:0): error 22
(probe0:ciss0:0:0:0): Unretryable Error
ciss0: command status 0x1 (target status) scsi status 0x2
(probe1:ciss0:0:1:0): error 22
(probe1:ciss0:0:1:0): Unretryable Error
pass0 at ciss0 bus 0 target 0 lun 0
pass0: <COMPAQ RAID 1 VOLUME OK> Fixed Direct Access SCSI-0 device
pass0: 135.168MB/s transfers
pass1 at ciss0 bus 0 target 1 lun 0
pass1: <COMPAQ RAID 5 VOLUME OK> Fixed Direct Access SCSI-0 device
pass1: 135.168MB/s transfers
pass2 at ata0 bus 0 target 0 lun 0
pass2: <COMPAQ SC-140S SE04> Removable CD-ROM SCSI-0 device
pass2: 16.000MB/s transfers
da0 at ciss0 bus 0 target 0 lun 0
da0: <COMPAQ RAID 1 VOLUME OK> Fixed Direct Access SCSI-0 device
da0: 135.168MB/s transfers
da0: 8673MB (17764320 512 byte sectors: 255H 32S/T 2177C)
da1 at ciss0 bus 0 target 1 lun 0
da1: <COMPAQ RAID 5 VOLUME OK> Fixed Direct Access SCSI-0 device
da1: 135.168MB/s transfers
da1: 52091MB (106683840 512 byte sectors: 255H 32S/T 13074C)
(cd0:ata0:0:0:0): error 6
(cd0:ata0:0:0:0): Unretryable Error
cd0 at ata0 bus 0 target 0 lun 0
cd0: <COMPAQ SC-140S SE04> Removable CD-ROM SCSI-0 device
cd0: 16.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
ATA PseudoRAID loaded
GEOM: new disk cd0
GEOM: new disk da0
GEOM: new disk da1
(cd0:ata0:0:0:0): error 6
(cd0:ata0:0:0:0): Unretryable Error
(cd0:ata0:0:0:0): error 6
(cd0:ata0:0:0:0): Unretryable Error
(cd0:ata0:0:0:0): error 6
(cd0:ata0:0:0:0): Unretryable Error
Trying to mount root from ufs:/dev/da0s2a
start_init: trying /sbin/init
Loading configuration files.
===============================================================================
MPTable
-------------------------------------------------------------------------------
MP Floating Pointer Structure:
location: BIOS
physical address: 0x000f4fd0
signature: '_MP_'
length: 16 bytes
version: 1.4
checksum: 0x00
mode: Virtual Wire
-------------------------------------------------------------------------------
MP Config Table Header:
physical address: 0x000f2ef8
signature: 'PCMP'
base table length: 532
version: 1.4
checksum: 0xe9
OEM ID: 'COMPAQ '
Product ID: 'PROLIANT '
OEM table pointer: 0x00000000
OEM table size: 0
entry count: 55
local APIC address: 0xfee00000
extended table length: 172
extended table checksum: 60
-------------------------------------------------------------------------------
MP Config Base Table Entries:
--
Processors: APIC ID Version State Family Model Step Flags
0 0x10 BSP, usable 6 2 1 0x0381
0 0x10 AP, usable 6 10 1 0x383fbff
1 0x10 AP, usable 6 10 1 0x383fbff
2 0x10 AP, usable 6 10 1 0x383fbff
--
Bus: Bus ID Type
0 PCI
1 PCI
2 PCI
15 ISA
--
I/O APICs: APIC ID Version State Address
8 0x11 usable 0xfec00000
--
I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
INT active-lo level 1 6:A 8 16
INT active-lo level 1 6:B 8 17
INT active-lo level 1 6:C 8 16
INT active-lo level 1 6:D 8 17
INT active-lo level 1 8:A 8 18
INT active-lo level 1 8:B 8 19
INT active-lo level 1 8:C 8 18
INT active-lo level 1 8:D 8 19
INT active-lo level 1 9:A 8 20
INT active-lo level 1 9:B 8 21
INT active-lo level 1 9:C 8 20
INT active-lo level 1 9:D 8 21
INT active-lo level 1 5:A 8 30
INT active-lo level 2 5:A 8 30
INT active-lo level 2 6:A 8 22
INT active-lo level 2 6:B 8 23
INT active-lo level 2 6:C 8 22
INT active-lo level 2 6:D 8 23
INT active-lo level 2 7:A 8 24
INT active-lo level 2 7:B 8 25
INT active-lo level 2 7:C 8 24
INT active-lo level 2 7:D 8 25
INT active-lo level 0 7:A 8 26
INT active-lo level 0 7:B 8 27
INT active-lo level 0 7:C 8 26
INT active-lo level 0 7:D 8 27
INT active-lo level 0 4:A 8 29
INT active-lo level 0 4:B 8 28
INT active-hi edge 15 1 8 1
INT active-hi edge 15 0 8 2
INT active-hi edge 15 3 8 3
INT active-hi edge 15 4 8 4
INT active-hi edge 15 5 8 5
INT active-hi edge 15 6 8 6
INT active-hi edge 15 7 8 7
INT active-hi edge 15 8 8 8
INT active-hi edge 15 9 8 9
INT active-hi edge 15 10 8 10
INT active-hi edge 15 11 8 11
INT active-hi edge 15 12 8 12
INT active-lo level 15 13 8 13
INT active-hi edge 15 14 8 14
INT active-hi edge 15 15 8 15
--
Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
ExtINT conforms conforms 15 0 255 0
NMI conforms conforms 15 0 255 1
--
MPTABLE OUT OF ORDER!
I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
ExtINT conforms conforms 15 0 8 0
-------------------------------------------------------------------------------
MP Config Extended Table Entries:
--
System Address Space
bus ID: 0 address type: I/O address
address base: 0x0
address range: 0x2c10
--
System Address Space
bus ID: 0 address type: memory address
address base: 0xf6000000
address range: 0x1b00000
--
System Address Space
bus ID: 1 address type: I/O address
address base: 0x3000
address range: 0x40
--
System Address Space
bus ID: 1 address type: memory address
address base: 0xf7b00000
address range: 0x300000
--
System Address Space
bus ID: 2 address type: I/O address
address base: 0x4000
address range: 0x100
--
System Address Space
bus ID: 2 address type: memory address
address base: 0xf7e00000
address range: 0x200000
--
System Address Space
bus ID: 0 address type: memory address
address base: 0xa0000
address range: 0x60000
--
Bus Heirarchy
bus ID: 15 bus info: 0x01 parent bus ID: 0
--
Compatibility Bus Address
bus ID: 0 address modifier: add
predefined range: 0x00000000
--
Compatibility Bus Address
bus ID: 1 address modifier: subtract
predefined range: 0x00000000
--
Compatibility Bus Address
bus ID: 2 address modifier: subtract
predefined range: 0x00000000
===============================================================================
_______________________________________________
[email protected] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-smp
To unsubscribe, send any mail to "[email protected]"