Problem Report: i915 driver most probably causing freezes on FreeBSD 13.1-RELEASE
Beñat Dagorret <[email protected]>
| Newsgroups | gmane.os.freebsd.devel.x11 |
|---|---|
| Message-ID | <[email protected]> |
Hello, I'm having an issue with the i915kms driver on a fresh FreeBSD 13.1-RELEASE install. The system boots and shows the Display Manager (LightDM) without any problem, but after logging in, X crashes leaving a black screen and a dead keyboard. The crash occurs always about 3 seconds after user login, no matter there was any user activity. I need to shutdown the system remotely from my laptop through ssh. Loading the xf86-video-intel driver from xorg.conf.d/ instead of the modesetting driver leads to the same result. Forcing DRI3 from configuration file in xorg.conf.d/ doesn't help, nor does changing the acceleration options. As of DRM, I have tried drm-kmod and drm-510-kmod, both installed from packages and ports. I'm pretty sure that it is NOT a desktop environment issue because I have the same behavior with LXDE and XFCE (the later installed just for testing purposes), and also because everything works as expected when the default xf86-video-vesa driver is used (but then the system is too slow and just unusable for everyday work). A very similar issue has been discussed for FreeBSD 13.0 here [https://forums.freebsd.org/threads/i915-driver-causing-freezes-on-freebsd-13-0.80016/], and I have added some details about my own experience with FreeBSD 13.1 here [https://forums.freebsd.org/threads/i915-driver-causing-freezes-on-freebsd-13-0.80016/post-582154]. I attach hereafter the output of several commands, as suggested in this page: https://wiki.freebsd.org/Graphics#Issues_.2F_Bugs . I can give more details if needed. Not sure whether this is the right place and/or way for reporting, so please be indulgent if I'm wrong. Thanks. Any advise or help will be welcomed, as I'm just clueless at this point after having tried every different configuration I can think of. Big thanks. Regards.
devinfo-vr.out
(text/plain, 13.8 KB)
nexus0
smbios0
I/O memory addresses:
0xf9c00-0xf9c1e
cryptosoft0
vtvga0
I/O memory addresses:
0xa0000-0xaffff
aesni0
ram0
I/O memory addresses:
0x0-0x9dbff
0x100000-0xda00bfff
0xda013000-0xda454fff
0xda7fa000-0xdadb0fff
0xdae33000-0xdae60fff
0xdaf74000-0xdafc5fff
0xdb047000-0xdb04cfff
0xdb065000-0xdb0bbfff
0xdb0c9000-0xdbe64fff
0xdbea5000-0xdbef3fff
0xdbfe4000-0xdbffcfff
0xdbfff000-0xdbffffff
0x100000000-0x31edfffff
apic0
I/O memory addresses:
0xfec00000-0xfec0001f
acpi0
Interrupt request lines:
0x9
I/O ports:
0x10-0x1f
0x22-0x3f
0x44-0x5f
0x62-0x63
0x65-0x6f
0x72-0x7f
0x80
0x84-0x86
0x88
0x8c-0x8e
0x90-0x9f
0xa2-0xbf
0xe0-0xef
0x4d0-0x4d1
0xa10-0xa1f
0xa20-0xa3f
0x1854-0x1857
I/O memory addresses:
0xf7fdf000-0xf7fdffff
0xf7fe0000-0xf7feffff
0xf8000000-0xfbffffff
0xfed10000-0xfed17fff
0xfed18000-0xfed18fff
0xfed19000-0xfed19fff
0xfed1c000-0xfed1ffff
0xfed20000-0xfed3ffff
0xfed40000-0xfed44fff
0xfed45000-0xfed8ffff
0xfed90000-0xfed93fff
0xfee00000-0xfeefffff
0xff000000-0xffffffff
cpu0 pnpinfo _HID=none _UID=0 _CID=none at handle=\_PR_.CPU0
est0
p4tcc0
acpi_perf0
cpufreq0
coretemp0
cpu1 pnpinfo _HID=none _UID=0 _CID=none at handle=\_PR_.CPU1
est1
p4tcc1
acpi_perf1
cpufreq1
coretemp1
unknown pnpinfo _HID=none _UID=0 _CID=none at handle=\_PR_.CPU2
unknown pnpinfo _HID=none _UID=0 _CID=none at handle=\_PR_.CPU3
unknown pnpinfo _HID=none _UID=0 _CID=none at handle=\_PR_.CPU4
unknown pnpinfo _HID=none _UID=0 _CID=none at handle=\_PR_.CPU5
unknown pnpinfo _HID=none _UID=0 _CID=none at handle=\_PR_.CPU6
unknown pnpinfo _HID=none _UID=0 _CID=none at handle=\_PR_.CPU7
pcib0 pnpinfo _HID=PNP0A08 _UID=0 _CID=PNP0A03 at handle=\_SB_.PCI0
I/O ports:
0xcf8-0xcff
pci0
PCI domain 0 bus numbers:
0
hostb0 pnpinfo vendor=0x8086 device=0x0c00 subvendor=0x103c subdevice=0x21d0 class=0x060000 at slot=0 function=0 dbsf=pci0:0:0:0
vgapci0 pnpinfo vendor=0x8086 device=0x0402 subvendor=0x103c subdevice=0x21d0 class=0x030000 at slot=2 function=0 dbsf=pci0:0:2:0 handle=\_SB_.PCI0.GFX0
Interrupt request lines:
0x26
I/O ports:
0xf000-0xf03f
I/O memory addresses:
0xe0000000-0xefffffff
0xf7800000-0xf7bfffff
drm0
drm1
drm2
i2c6
drm3
drm4
i2c7
drm5
drmn0
drm128
i2c0
i2c1
i2c2
i2c3
i2c4
i2c5
fbd0
hdac0 pnpinfo vendor=0x8086 device=0x0c0c subvendor=0x103c subdevice=0x21d0 class=0x040300 at slot=3 function=0 dbsf=pci0:0:3:0 handle=\_SB_.PCI0.B0D3
Interrupt request lines:
0x20
I/O memory addresses:
0xf7c34000-0xf7c37fff
hdacc0 pnpinfo vendor=0x8086 device=0x2807 revision=0x00 stepping=0x00 at cad=0
hdaa0 pnpinfo type=0x01 subsystem=0x80860101 at nid=1
pcm0 at nid=3
xhci0 pnpinfo vendor=0x8086 device=0x8c31 subvendor=0x103c subdevice=0x21d0 class=0x0c0330 at slot=20 function=0 dbsf=pci0:0:20:0 handle=\_SB_.PCI0.XHC_
Interrupt request lines:
0x21
I/O memory addresses:
0xf7c20000-0xf7c2ffff
usbus0
uhub1
ukbd0 pnpinfo vendor=0x04d9 product=0x1503 devclass=0x00 devsubclass=0x00 devproto=0x00 sernum="" release=0x0310 mode=host intclass=0x03 intsubclass=0x01 intprotocol=0x01 at bus=0 hubaddr=1 port=9 devaddr=3 interface=0 ugen=ugen0.3
uhid0 pnpinfo vendor=0x04d9 product=0x1503 devclass=0x00 devsubclass=0x00 devproto=0x00 sernum="" release=0x0310 mode=host intclass=0x03 intsubclass=0x00 intprotocol=0x00 at bus=0 hubaddr=1 port=9 devaddr=3 interface=1 ugen=ugen0.3
ums0 pnpinfo vendor=0x046d product=0xc077 devclass=0x00 devsubclass=0x00 devproto=0x00 sernum="" release=0x7200 mode=host intclass=0x03 intsubclass=0x01 intprotocol=0x02 at bus=0 hubaddr=1 port=13 devaddr=4 interface=0 ugen=ugen0.4
unknown pnpinfo vendor=0x8086 device=0x8c3a subvendor=0x103c subdevice=0x21d0 class=0x078000 at slot=22 function=0 dbsf=pci0:0:22:0
I/O memory addresses:
0xf7c40000-0xf7c4000f
uart2 pnpinfo vendor=0x8086 device=0x8c3d subvendor=0x103c subdevice=0x21d0 class=0x070002 at slot=22 function=3 dbsf=pci0:0:22:3
Interrupt request lines:
0x22
I/O ports:
0xf0e0-0xf0e7
I/O memory addresses:
0xf7c3e000-0xf7c3efff
em0 pnpinfo vendor=0x8086 device=0x153a subvendor=0x103c subdevice=0x21d0 class=0x020000 at slot=25 function=0 dbsf=pci0:0:25:0 handle=\_SB_.PCI0.GLAN
Interrupt request lines:
0x23
I/O ports:
0xf080-0xf09f
I/O memory addresses:
0xf7c00000-0xf7c1ffff
0xf7c3d000-0xf7c3dfff
ehci0 pnpinfo vendor=0x8086 device=0x8c2d subvendor=0x103c subdevice=0x21d0 class=0x0c0320 at slot=26 function=0 dbsf=pci0:0:26:0 handle=\_SB_.PCI0.EHC2
Interrupt request lines:
0x10
I/O memory addresses:
0xf7c3c000-0xf7c3c3ff
usbus1
uhub0
uhub3 pnpinfo vendor=0x8087 product=0x8008 devclass=0x09 devsubclass=0x00 devproto=0x01 sernum="" release=0x0004 mode=host intclass=0x09 intsubclass=0x00 intprotocol=0x00 at bus=1 hubaddr=1 port=1 devaddr=2 interface=0 ugen=ugen1.2
hdac1 pnpinfo vendor=0x8086 device=0x8c20 subvendor=0x103c subdevice=0x21d0 class=0x040300 at slot=27 function=0 dbsf=pci0:0:27:0 handle=\_SB_.PCI0.HDEF
Interrupt request lines:
0x24
I/O memory addresses:
0xf7c30000-0xf7c33fff
hdacc1 pnpinfo vendor=0x10ec device=0x0221 revision=0x00 stepping=0x03 at cad=0
hdaa1 pnpinfo type=0x01 subsystem=0x103c21d0 at nid=1
pcm1 at nid=23,26
pcm2 at nid=20,33
pcib1 pnpinfo vendor=0x8086 device=0x8c10 subvendor=0x103c subdevice=0x21d0 class=0x060400 at slot=28 function=0 dbsf=pci0:0:28:0 handle=\_SB_.PCI0.RP01
PCI domain 0 bus numbers:
4
pci1
pcib1 bus numbers:
4
pcib2 pnpinfo vendor=0x8086 device=0x8c18 subvendor=0x103c subdevice=0x21d0 class=0x060400 at slot=28 function=4 dbsf=pci0:0:28:4 handle=\_SB_.PCI0.RP05
PCI domain 0 bus numbers:
8
pci2
pcib2 bus numbers:
8
ehci1 pnpinfo vendor=0x8086 device=0x8c26 subvendor=0x103c subdevice=0x21d0 class=0x0c0320 at slot=29 function=0 dbsf=pci0:0:29:0 handle=\_SB_.PCI0.EHC1
Interrupt request lines:
0x17
I/O memory addresses:
0xf7c3b000-0xf7c3b3ff
usbus2
uhub2
uhub4 pnpinfo vendor=0x8087 product=0x8000 devclass=0x09 devsubclass=0x00 devproto=0x01 sernum="" release=0x0004 mode=host intclass=0x09 intsubclass=0x00 intprotocol=0x00 at bus=2 hubaddr=1 port=1 devaddr=2 interface=0 ugen=ugen2.2
isab0 pnpinfo vendor=0x8086 device=0x8c4c subvendor=0x103c subdevice=0x21d0 class=0x060100 at slot=31 function=0 dbsf=pci0:0:31:0 handle=\_SB_.PCI0.LPCB
isa0
orm0 pnpinfo pnpid=ORM0000
I/O memory addresses:
0xd0000-0xd0fff
sc0
vga0 pnpinfo pnpid=PNP0900
I/O ports:
0x3c0-0x3df
fdc0
ppc0
uart0
uart1
ahci0 pnpinfo vendor=0x8086 device=0x8c02 subvendor=0x103c subdevice=0x21d0 class=0x010601 at slot=31 function=2 dbsf=pci0:0:31:2 handle=\_SB_.PCI0.SAT0
Interrupt request lines:
0x25
I/O ports:
0xf060-0xf07f
0xf0a0-0xf0a3
0xf0b0-0xf0b7
0xf0c0-0xf0c3
0xf0d0-0xf0d7
I/O memory addresses:
0xf7c3a000-0xf7c3a7ff
ahcich0 at channel=0
I/O memory addresses:
0xf7c3a100-0xf7c3a17f
ahcich1 at channel=1 (disabled)
ahcich2 at channel=2 (disabled)
ahcich3 at channel=3 (disabled)
ahcich4 at channel=4 (disabled)
ahcich5 at channel=5 (disabled)
ahciem0
I/O memory addresses:
0xf7c3a020-0xf7c3a023
0xf7c3a580-0xf7c3a587
ichsmb0 pnpinfo vendor=0x8086 device=0x8c22 subvendor=0x103c subdevice=0x21d0 class=0x0c0500 at slot=31 function=3 dbsf=pci0:0:31:3 handle=\_SB_.PCI0.SBUS
Interrupt request lines:
0x12
I/O ports:
0xf040-0xf05f
I/O memory addresses:
0xf7c39000-0xf7c390ff
smbus0
acpi_sysresource0 pnpinfo _HID=PNP0C01 _UID=1 _CID=none at handle=\_SB_.PCI0.TPMX
atdma0 pnpinfo _HID=PNP0200 _UID=0 _CID=none at handle=\_SB_.PCI0.LPCB.DMAC
DMA request lines:
4
I/O ports:
0xc0-0xdf
unknown pnpinfo _HID=INT0800 _UID=0 _CID=none at handle=\_SB_.PCI0.LPCB.FWHD
hpet0 pnpinfo _HID=PNP0103 _UID=0 _CID=none at handle=\_SB_.PCI0.LPCB.HPET
Interrupt request lines:
0x18
0x19
0x1a
0x1b
0x1c
0x1d
0x1e
0x1f
I/O memory addresses:
0xfed00000-0xfed003ff
unknown pnpinfo _HID=PNP0000 _UID=0 _CID=none at handle=\_SB_.PCI0.LPCB.IPIC
I/O ports:
0x20-0x21
0xa0-0xa1
fpupnp0 pnpinfo _HID=PNP0C04 _UID=0 _CID=none at handle=\_SB_.PCI0.LPCB.MATH
I/O ports:
0xf0
acpi_sysresource1 pnpinfo _HID=PNP0C02 _UID=2 _CID=none at handle=\_SB_.PCI0.LPCB.LDRC
atrtc0 pnpinfo _HID=PNP0B00 _UID=0 _CID=none at handle=\_SB_.PCI0.LPCB.RTC_
Interrupt request lines:
0x8
I/O ports:
0x70-0x71
attimer0 pnpinfo _HID=PNP0100 _UID=0 _CID=none at handle=\_SB_.PCI0.LPCB.TIMR
Interrupt request lines:
0x0
I/O ports:
0x40-0x43
acpi_sysresource2 pnpinfo _HID=INT3F0D _UID=0 _CID=PNP0C02 at handle=\_SB_.PCI0.LPCB.CWDT
acpi_sysresource3 pnpinfo _HID=PNP0C02 _UID=273 _CID=none at handle=\_SB_.PCI0.LPCB.SIO1
atkbdc0 pnpinfo _HID=PNP0303 _UID=0 _CID=PNP030B at handle=\_SB_.PCI0.LPCB.PS2K
Interrupt request lines:
0x1
I/O ports:
0x60
0x64
atkbd0
psm0
psmcpnp0 pnpinfo _HID=PNP0F03 _UID=0 _CID=PNP0F13 at handle=\_SB_.PCI0.LPCB.PS2M
acpi_sysresource4 pnpinfo _HID=PNP0C02 _UID=16 _CID=none at handle=\_SB_.PCI0.LPCB.RMSC
unknown pnpinfo _HID=PNP0501 _UID=1 _CID=none at handle=\_SB_.PCI0.LPCB.UAR1 (disabled)
unknown pnpinfo _HID=PNP0501 _UID=2 _CID=none at handle=\_SB_.PCI0.LPCB.UAR2 (disabled)
unknown pnpinfo _HID=PNP0401 _UID=0 _CID=none at handle=\_SB_.PCI0.LPCB.LPTE (disabled)
unknown pnpinfo _HID=IFX0102 _UID=1 _CID=PNP0C31 at handle=\_SB_.PCI0.LPCB.TPM_
unknown pnpinfo _HID=PNP0C09 _UID=1 _CID=none at handle=\_SB_.PCI0.LPCB.H_EC (disabled)
unknown pnpinfo _HID=PNP0C0A _UID=0 _CID=none at handle=\_SB_.PCI0.LPCB.H_EC.BAT0 (disabled)
unknown pnpinfo _HID=PNP0C0A _UID=1 _CID=none at handle=\_SB_.PCI0.LPCB.H_EC.BAT1 (disabled)
unknown pnpinfo _HID=PNP0C0A _UID=2 _CID=none at handle=\_SB_.PCI0.LPCB.H_EC.BAT2 (disabled)
acpi_sysresource5 pnpinfo _HID=PNP0C02 _UID=1 _CID=none at handle=\_SB_.PCI0.PDRC
unknown pnpinfo _HID=INTC0102 _UID=0 _CID=PNP0C31 at handle=\_SB_.PCI0.ITPM (disabled)
unknown pnpinfo _HID=ABCD0000 _UID=2 _CID=PNP0C15 at handle=\_SB_.PCI0.DOCK (disabled)
pci_link0 pnpinfo _HID=PNP0C0F _UID=1 _CID=none at handle=\_SB_.LNKA
pci_link1 pnpinfo _HID=PNP0C0F _UID=2 _CID=none at handle=\_SB_.LNKB
pci_link2 pnpinfo _HID=PNP0C0F _UID=3 _CID=none at handle=\_SB_.LNKC
pci_link3 pnpinfo _HID=PNP0C0F _UID=4 _CID=none at handle=\_SB_.LNKD
pci_link4 pnpinfo _HID=PNP0C0F _UID=5 _CID=none at handle=\_SB_.LNKE
pci_link5 pnpinfo _HID=PNP0C0F _UID=6 _CID=none at handle=\_SB_.LNKF
pci_link6 pnpinfo _HID=PNP0C0F _UID=7 _CID=none at handle=\_SB_.LNKG
pci_link7 pnpinfo _HID=PNP0C0F _UID=8 _CID=none at handle=\_SB_.LNKH
acpi_button0 pnpinfo _HID=PNP0C0C _UID=170 _CID=none at handle=\_SB_.PWRB
unknown pnpinfo _HID=INT33A1 _UID=1 _CID=PNP0D80 at handle=\_SB_.PEPD (disabled)
unknown pnpinfo _HID=INT3420 _UID=0 _CID=none at handle=\_SB_.BTKL (disabled)
unknown pnpinfo _HID=PNP0C0D _UID=0 _CID=none at handle=\_SB_.LID0 (disabled)
unknown pnpinfo _HID=PNP0C01 _UID=2 _CID=none at handle=\_SB_.MEM2 (disabled)
acpi_wmi0 pnpinfo _HID=PNP0C14 _UID=0 _CID=none at handle=\_SB_.WMID
unknown pnpinfo _HID=none _UID=0 _CID=none at handle=\_TZ_.FN00
unknown pnpinfo _HID=PNP0C0B _UID=0 _CID=none at handle=\_TZ_.FAN0
unknown pnpinfo _HID=none _UID=0 _CID=none at handle=\_TZ_.FN01
unknown pnpinfo _HID=PNP0C0B _UID=1 _CID=none at handle=\_TZ_.FAN1
acpi_tz0 pnpinfo _HID=none _UID=0 _CID=none at handle=\_TZ_.TZ00
acpi_tz1 pnpinfo _HID=none _UID=0 _CID=none at handle=\_TZ_.TZ01
unknown pnpinfo _HID=PNP0C02 _UID=5 _CID=none at handle=\HTAM (disabled)
acpi_timer0 pnpinfo unknown
I/O ports:
0x408-0x40b
inxi-F.out
(text/plain, 1.6 KB)
System:
Host: ilargi Kernel: FreeBSD 13.1-RELEASE amd64 bits: 64
Console: pty pts/0 OS: FreeBSD 13.1-RELEASE
Machine:
Type: Desktop System: Hewlett-Packard
product: HP ProDesk 600 G1 DM v: N/A serial: XXXXXXXXXX
Mobo: Hewlett-Packard model: 21D0 serial: XXXXXXXXXX
UEFI: Hewlett-Packard v: L04 v02.07 rev: 2.7 date: 07/15/2014
CPU:
Info: dual core model: Intel Pentium G3240T bits: 64
type: MCP cache: L2: 512 KiB note: check
Speed (MHz): 2693 min/max: N/A
cores: No OS support for core speeds.
Graphics:
Device-1: Intel Xeon E3-1200 v3/4th Gen Core Processor
Integrated Graphics
driver: vgapci
Display: server: X.org 1.20.14 driver: loaded: modesetting
tty: 66x22
Message: Advanced graphics data unavailable in console for
root.
Audio:
Device-1: Intel Xeon E3-1200 v3/4th Gen Core Processor HD
Audio
driver: hdac
Device-2: Intel 8 Series/C220 Series High Definition Audio
driver: hdac
Sound Server-1: OSS v: 2009061500 running: yes
Network:
Device-1: Intel Ethernet I217-LM driver: em
IF: em0 state: active speed: 100baseTX duplex: full-duplex
mac: 40:a8:f0:5a:8f:b1
Drives:
Local Storage: total: 232.89 GiB used: 15.87 GiB (6.8%)
ID-1: /dev/ada0 vendor: Crucial
model: CT250MX500SSD1 M3CR045 size: 232.89 GiB scheme: GPT
Partition:
ID-1: / size: 221.7 GiB used: 15.87 GiB (7.2%) fs: ufs
dev: /dev/rootfs
Swap:
ID-1: swap-1 type: partition size: 4 GiB used: 0 KiB (0.0%)
dev: /dev/gpt/swapfs
Sensors:
System Temperatures: cpu: 42.0 C mobo: N/A
Fan Speeds (RPM): N/A
Info:
Processes: 68 Uptime: 32m Memory: 11.88 GiB
used: 1.12 GiB (9.4%) Init: init (BSD) Shell: Bash
inxi: 3.3.11
lspci-xxvvv.out
(text/plain, 29.3 KB)
00:00.0 Host bridge: Intel Corporation 4th Gen Core Processor DRAM Controller (rev 06) Subsystem: Hewlett-Packard Company Device 21d0 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> 00: 86 80 00 0c 06 01 90 20 06 00 00 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 d0 21 30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 40: 01 90 d1 fe 00 00 00 00 01 00 d1 fe 00 00 00 00 50: 09 02 00 00 31 00 00 00 17 00 10 df 01 00 00 dc 60: 05 00 00 f8 00 00 00 00 01 80 d1 fe 00 00 00 00 70: 00 00 00 fe 02 00 00 00 00 0c 00 fe 7f 00 00 00 80: 10 11 11 01 00 00 33 00 1a 00 00 00 00 00 00 00 90: 01 00 00 fe 02 00 00 00 01 00 d0 1e 03 00 00 00 a0: 01 00 00 00 03 00 00 00 01 00 e0 1e 03 00 00 00 b0: 01 00 20 dd 01 00 00 dd 01 00 00 dc 01 00 20 df c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 09 00 0c 01 61 80 84 62 e0 00 24 44 00 00 00 00 f0: 00 00 00 00 c8 0f 03 00 00 00 00 00 00 00 00 00 00:02.0 VGA compatible controller: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor Integrated Graphics Controller (rev 06) (prog-if 00 [VGA controller]) Subsystem: Hewlett-Packard Company Device 21d0 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at f7800000 (64-bit, non-prefetchable) Region 2: Memory at e0000000 (64-bit, prefetchable) Region 4: I/O ports at f000 Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee00000 Data: 003e Capabilities: [d0] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [a4] PCI Advanced Features AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP- 00: 86 80 02 04 07 04 90 00 06 00 00 03 00 00 00 00 10: 04 00 80 f7 00 00 00 00 0c 00 00 e0 00 00 00 00 20: 01 f0 00 00 00 00 00 00 00 00 00 00 3c 10 d0 21 30: 00 00 00 00 90 00 00 00 00 00 00 00 10 01 00 00 40: 09 00 0c 01 61 80 84 62 e0 00 24 44 00 00 00 00 50: 09 02 00 00 31 00 00 00 00 00 00 00 01 00 20 dd 60: 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 05 d0 01 00 00 00 e0 fe 3e 00 00 00 00 00 00 00 a0: 00 00 00 00 13 00 06 03 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 01 a4 22 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 80 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 06 00 18 d0 f8 db 00:03.0 Audio device: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller (rev 06) Subsystem: Hewlett-Packard Company Device 21d0 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at f7c34000 (64-bit, non-prefetchable) Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee02000 Data: 0031 Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0 ExtTag- RBE- FLReset+ DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend- 00: 86 80 0c 0c 06 05 10 00 06 00 03 04 10 00 00 00 10: 04 40 c3 f7 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 d0 21 30: 00 00 00 00 50 00 00 00 00 00 00 00 10 01 00 00 40: 00 00 00 00 61 80 84 62 e0 00 24 44 31 00 00 00 50: 01 60 02 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 05 70 01 00 00 20 e0 fe 31 00 00 00 00 00 00 00 70: 10 00 91 00 c0 0f 00 10 00 08 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI (rev 04) (prog-if 30 [XHCI]) Subsystem: Hewlett-Packard Company Device 21d0 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at f7c20000 (64-bit, non-prefetchable) Capabilities: [70] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+ Address: 00000000fee00000 Data: 003a 00: 86 80 31 8c 06 05 90 02 04 30 03 0c 00 00 00 00 10: 04 00 c2 f7 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 d0 21 30: 00 00 00 00 70 00 00 00 00 00 00 00 10 01 00 00 40: fd 01 36 80 89 c6 0f 80 00 00 00 00 00 00 00 00 50: 9f 6e 88 07 00 00 00 00 00 00 00 00 00 00 00 00 60: 30 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 01 80 c2 c1 08 00 00 00 00 00 00 00 00 00 00 00 80: 05 00 87 00 00 00 e0 fe 00 00 00 00 3a 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 40 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 0f 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 50 02 00 01 00 00 00 03 03 20 00 10 00 00 00 00 d0: ff 3f 00 00 ff 3f 00 00 3f 00 00 00 3f 00 00 00 e0: a0 00 00 00 c4 2e 00 00 0c 00 00 00 d8 d8 d8 08 f0: 00 00 00 00 00 00 00 00 b1 0f 06 08 00 00 00 00 00:16.0 Communication controller: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #1 (rev 04) Subsystem: Hewlett-Packard Company Device 21d0 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at f7c40000 (64-bit, non-prefetchable) Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [8c] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 00: 86 80 3a 8c 06 00 10 00 04 00 80 07 00 00 80 00 10: 04 00 c4 f7 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 d0 21 30: 00 00 00 00 50 00 00 00 00 00 00 00 10 01 00 00 40: 45 02 00 1e 20 00 01 80 06 23 00 60 e0 2f 00 10 50: 01 8c 03 c8 08 00 00 00 00 00 00 00 00 00 00 00 60: 00 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 05 00 80 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 02 00 00 c0 c0: c7 0e c8 82 e6 15 04 02 33 78 0f b4 c0 2e fd 74 d0: a7 a2 84 8d 76 8b db 6e 66 14 b8 85 2b 02 1b 50 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:16.3 Serial controller: Intel Corporation 8 Series/C220 Series Chipset Family KT Controller (rev 04) (prog-if 02 [16550]) Subsystem: Hewlett-Packard Company Device 21d0 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: I/O ports at f0e0 Region 1: Memory at f7c3e000 (32-bit, non-prefetchable) Capabilities: [c8] Power Management version 3 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee02000 Data: 0032 00: 86 80 3d 8c 07 04 b0 00 04 02 00 07 00 00 00 00 10: e1 f0 00 00 00 e0 c3 f7 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 d0 21 30: 00 00 00 00 c8 00 00 00 00 00 00 00 13 02 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 01 d0 23 00 08 00 00 00 d0: 05 00 81 00 00 20 e0 fe 00 00 00 00 32 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:19.0 Ethernet controller: Intel Corporation Ethernet Connection I217-LM (rev 04) Subsystem: Hewlett-Packard Company Device 21d0 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 20 Region 0: Memory at f7c00000 (32-bit, non-prefetchable) Region 1: Memory at f7c3d000 (32-bit, non-prefetchable) Region 2: I/O ports at f080 Capabilities: [c8] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee00000 Data: 003b Capabilities: [e0] PCI Advanced Features AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP- 00: 86 80 3a 15 07 05 10 00 04 00 00 02 00 00 00 00 10: 00 00 c0 f7 00 d0 c3 f7 81 f0 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 d0 21 30: 00 00 00 00 c8 00 00 00 00 00 00 00 14 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 04 54 00 00 8f b1 00 80 a0: 00 00 00 00 00 00 00 00 46 08 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 01 d0 22 c8 00 20 00 07 d0: 05 e0 81 00 00 00 e0 fe 00 00 00 00 3b 00 00 00 e0: 13 00 06 03 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:1a.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #2 (rev 04) (prog-if 20 [EHCI]) Subsystem: Hewlett-Packard Company Device 21d0 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at f7c3c000 (32-bit, non-prefetchable) Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP- 00: 86 80 2d 8c 06 01 90 02 04 20 03 0c 00 00 00 00 10: 00 c0 c3 f7 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 d0 21 30: 00 00 00 00 50 00 00 00 00 00 00 00 10 01 00 00 40: 00 00 00 00 a8 0a 05 1b 00 00 00 00 00 00 00 00 50: 01 58 c2 c9 00 00 00 00 0a 98 a0 20 00 00 00 00 60: 20 20 ff 07 3c 00 00 00 01 00 00 01 00 20 00 40 70: 00 00 df 3f 00 00 00 03 4f 01 00 01 8c 40 00 00 80: 00 00 80 00 11 88 0c 93 70 0d 00 24 01 04 02 00 90: 00 00 00 00 00 00 00 00 13 00 06 03 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 aa ff 00 00 00 78 e2 27 00 00 00 e0: 00 00 00 00 ff ff ff ff ff ff ff ff bc eb f7 29 f0: 00 00 00 00 88 85 80 00 b1 0f 06 08 08 17 1a 20 00:1b.0 Audio device: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller (rev 04) Subsystem: Hewlett-Packard Company Device 21d0 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 22 Region 0: Memory at f7c30000 (64-bit, non-prefetchable) Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee00000 Data: 003c Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0 ExtTag- RBE- FLReset+ DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01 Status: NegoPending- InProgress- VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=2 ArbSelect=Fixed TC/VC=04 Status: NegoPending- InProgress- 00: 86 80 20 8c 06 05 10 00 04 00 03 04 10 00 00 00 10: 04 00 c3 f7 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 d0 21 30: 00 00 00 00 50 00 00 00 00 00 00 00 16 01 00 00 40: 03 00 00 17 00 00 00 00 00 00 00 00 00 00 00 00 50: 01 60 42 c8 00 00 00 00 00 00 00 00 00 00 00 00 60: 05 70 81 00 00 00 e0 fe 00 00 00 00 3c 00 00 00 70: 10 00 91 00 00 00 00 10 00 08 10 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 04 02 01 00 60 00 00 00 0c 85 82 10 00 33 02 d0: 00 0c 85 02 10 00 33 02 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 b1 0f 06 08 00 00 00 00 00:1c.0 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #1 (rev d4) (prog-if 00 [Normal decode]) Subsystem: Hewlett-Packard Company Device 21d0 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: [disabled] [16-bit] Memory behind bridge: [disabled] [32-bit] Prefetchable memory behind bridge: [disabled] [64-bit] Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0 ExtTag- RBE+ DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend- LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <1us, L1 <4us ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp- LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes, Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x0 TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Slot #0, PowerLimit 0W; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock- Changed: MRL- PresDet- LinkState- RootCap: CRSVisible- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Range ABC, TimeoutDis+ NROPrPrP- LTR+ 10BitTagComp- 10BitTagReq- OBFF Via WAKE#, ExtFmt- EETLPPrefix- EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit- FRS- LN System CLS Not Supported, TPHComp- ExtTPHComp- ARIFwd- AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR+ 10BitTagReq- OBFF Disabled, ARIFwd- AtomicOpsCtl: ReqEn- EgressBlck- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance Preset/De-emphasis: -6dB de-emphasis, 0dB preshoot LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete- EqualizationPhase1- EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest- Retimer- 2Retimers- CrosslinkRes: unsupported Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [90] Subsystem: Hewlett-Packard Company Device 21d0 Capabilities: [a0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 00: 86 80 10 8c 07 01 10 00 d4 00 04 06 10 00 81 00 10: 00 00 00 00 00 00 00 00 00 04 04 00 f0 00 00 20 20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 10 01 12 00 40: 10 80 42 01 00 80 00 00 00 00 10 00 12 4c 31 01 50: 03 00 01 10 60 00 04 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 17 08 08 00 00 04 00 00 00 00 00 00 70: 02 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 05 90 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 0d a0 00 00 3c 10 d0 21 00 00 00 00 00 00 00 00 a0: 01 00 03 c8 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 01 00 08 00 00 02 00 11 09 00 00 00 00 e0: 00 3f 00 00 00 00 00 00 03 00 00 00 00 00 00 00 f0: 50 00 00 00 80 f5 00 00 b1 0f 06 08 01 00 0b 41 00:1c.4 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #5 (rev d4) (prog-if 00 [Normal decode]) Subsystem: Hewlett-Packard Company Device 21d0 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Bus: primary=00, secondary=08, subordinate=08, sec-latency=0 I/O behind bridge: [disabled] [16-bit] Memory behind bridge: [disabled] [32-bit] Prefetchable memory behind bridge: [disabled] [64-bit] Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0 ExtTag- RBE+ DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend- LnkCap: Port #5, Speed 5GT/s, Width x4, ASPM L0s L1, Exit Latency L0s <1us, L1 <16us ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp- LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes, Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x0 TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #4, PowerLimit 25W; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState- RootCap: CRSVisible- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Range ABC, TimeoutDis+ NROPrPrP- LTR+ 10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix- EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit- FRS- LN System CLS Not Supported, TPHComp- ExtTPHComp- ARIFwd- AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR+ 10BitTagReq- OBFF Disabled, ARIFwd- AtomicOpsCtl: ReqEn- EgressBlck- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance Preset/De-emphasis: -6dB de-emphasis, 0dB preshoot LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete- EqualizationPhase1- EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest- Retimer- 2Retimers- CrosslinkRes: unsupported Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [90] Subsystem: Hewlett-Packard Company Device 21d0 Capabilities: [a0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 00: 86 80 18 8c 07 01 10 00 d4 00 04 06 10 00 81 00 10: 00 00 00 00 00 00 00 00 00 08 08 00 f0 00 00 20 20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 10 01 12 00 40: 10 80 42 01 00 80 00 00 00 00 10 00 42 4c 32 05 50: 03 00 01 10 00 fd 24 00 00 00 48 00 00 00 00 00 60: 00 00 00 00 17 08 00 00 00 04 00 00 00 00 00 00 70: 02 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 05 90 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 0d a0 00 00 3c 10 d0 21 00 00 00 00 00 00 00 00 a0: 01 00 03 c8 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 01 02 08 00 00 08 80 11 8b 00 00 00 00 e0: 00 3f 00 00 00 00 00 00 03 00 00 00 00 00 00 00 f0: 50 00 00 00 40 00 00 00 b1 0f 06 08 00 c0 00 05 00:1d.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #1 (rev 04) (prog-if 20 [EHCI]) Subsystem: Hewlett-Packard Company Device 21d0 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at f7c3b000 (32-bit, non-prefetchable) Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP- 00: 86 80 26 8c 06 01 90 02 04 20 03 0c 00 00 00 00 10: 00 b0 c3 f7 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 d0 21 30: 00 00 00 00 50 00 00 00 00 00 00 00 17 01 00 00 40: 00 00 00 00 c2 13 d2 19 00 00 00 00 00 00 00 00 50: 01 58 c2 c9 00 00 00 00 0a 98 a0 20 00 00 00 00 60: 20 20 ff 07 a4 00 00 00 01 00 00 01 00 20 08 40 70: 00 00 df 3f 50 02 00 01 4f 01 00 01 8c 40 00 00 80: 00 00 80 00 11 88 0c 93 70 0d 00 24 01 04 02 00 90: 00 00 00 00 00 00 00 00 13 00 06 03 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 aa ff 00 00 00 ff ff 27 00 00 00 e0: 00 00 00 00 ff ff ff ff ff ff ff ff 28 43 32 29 f0: 00 00 00 00 88 85 80 00 b1 0f 06 08 08 17 1a 20 00:1f.0 ISA bridge: Intel Corporation Q85 Express LPC Controller (rev 04) Subsystem: Hewlett-Packard Company Device 21d0 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> 00: 86 80 4c 8c 07 01 10 02 04 00 01 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 d0 21 30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 40: 01 04 00 00 80 00 00 00 01 05 00 00 11 00 00 00 50: f8 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 8b 80 8b 8a 90 00 00 00 85 80 83 84 f8 f0 00 00 70: 78 f0 78 f0 78 f0 78 f0 78 f0 78 f0 78 f0 78 f0 80: 10 00 08 14 01 0a fc 00 01 08 fc 00 00 00 00 00 90: 00 00 00 00 00 0f 00 00 00 00 00 00 00 00 00 00 a0: 38 5e 80 18 09 38 06 00 00 46 00 00 00 00 01 80 b0: 00 00 00 00 00 00 00 00 00 10 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 33 22 11 00 67 45 00 00 cf ff 00 00 2a 00 00 00 e0: 09 00 0c 10 00 00 00 00 01 00 c0 91 00 00 00 00 f0: 01 c0 d1 fe 00 00 00 00 b1 0f 06 08 00 00 00 00 00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 04) (prog-if 01 [AHCI 1.0]) Subsystem: Hewlett-Packard Company Device 21d0 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: I/O ports at f0d0 Region 1: I/O ports at f0c0 Region 2: I/O ports at f0b0 Region 3: I/O ports at f0a0 Region 4: I/O ports at f060 Region 5: Memory at f7c3a000 (32-bit, non-prefetchable) Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee00000 Data: 003d Capabilities: [70] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004 00: 86 80 02 8c 07 05 b0 02 04 01 06 01 00 00 00 00 10: d1 f0 00 00 c1 f0 00 00 b1 f0 00 00 a1 f0 00 00 20: 61 f0 00 00 00 a0 c3 f7 00 00 00 00 3c 10 d0 21 30: 00 00 00 00 80 00 00 00 00 00 00 00 13 02 00 00 40: 00 80 00 80 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 01 a8 03 40 08 00 00 00 00 00 00 00 00 00 00 00 80: 05 70 01 00 00 00 e0 fe 3d 00 00 00 00 00 00 00 90: 60 3e 01 81 83 01 00 3e 20 02 5c 20 20 00 00 80 a0: a8 00 00 00 00 00 00 00 12 00 10 00 48 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 b1 0f 06 08 00 00 00 00 00:1f.3 SMBus: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller (rev 04) Subsystem: Hewlett-Packard Company Device 21d0 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 18 Region 0: Memory at f7c39000 (64-bit, non-prefetchable) Region 4: I/O ports at f040 00: 86 80 22 8c 03 01 80 02 04 00 05 0c 00 00 00 00 10: 04 90 c3 f7 00 00 00 00 00 00 00 00 00 00 00 00 20: 41 f0 00 00 00 00 00 00 00 00 00 00 3c 10 d0 21 30: 00 00 00 00 00 00 00 00 00 00 00 00 12 03 00 00 40: 11 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 03 04 04 00 00 00 08 08 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 b1 0f 06 08 00 00 00 00
piconf-lvbce.out
(text/plain, 8.1 KB)
hostb0@pci0:0:0:0: class=0x060000 rev=0x06 hdr=0x00 vendor=0x8086 device=0x0c00 subvendor=0x103c subdevice=0x21d0
vendor = 'Intel Corporation'
device = '4th Gen Core Processor DRAM Controller'
class = bridge
subclass = HOST-PCI
cap 09[e0] = vendor (length 12) Intel cap 0 version 1
PCI errors = Received Master-Abort
vgapci0@pci0:0:2:0: class=0x030000 rev=0x06 hdr=0x00 vendor=0x8086 device=0x0402 subvendor=0x103c subdevice=0x21d0
vendor = 'Intel Corporation'
device = 'Xeon E3-1200 v3/4th Gen Core Processor Integrated Graphics Controller'
class = display
subclass = VGA
bar [10] = type Memory, range 64, base 0xf7800000, size 4194304, enabled
bar [18] = type Prefetchable Memory, range 64, base 0xe0000000, size 268435456, enabled
bar [20] = type I/O Port, range 32, base 0xf000, size 64, enabled
cap 05[90] = MSI supports 1 message enabled with 1 message
cap 01[d0] = powerspec 2 supports D0 D3 current D0
cap 13[a4] = PCI Advanced Features: FLR TP
hdac0@pci0:0:3:0: class=0x040300 rev=0x06 hdr=0x00 vendor=0x8086 device=0x0c0c subvendor=0x103c subdevice=0x21d0
vendor = 'Intel Corporation'
device = 'Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller'
class = multimedia
subclass = HDA
bar [10] = type Memory, range 64, base 0xf7c34000, size 16384, enabled
cap 01[50] = powerspec 2 supports D0 D3 current D0
cap 05[60] = MSI supports 1 message enabled with 1 message
cap 10[70] = PCI-Express 1 root endpoint max data 128(128) FLR NS
max read 128
xhci0@pci0:0:20:0: class=0x0c0330 rev=0x04 hdr=0x00 vendor=0x8086 device=0x8c31 subvendor=0x103c subdevice=0x21d0
vendor = 'Intel Corporation'
device = '8 Series/C220 Series Chipset Family USB xHCI'
class = serial bus
subclass = USB
bar [10] = type Memory, range 64, base 0xf7c20000, size 65536, enabled
cap 01[70] = powerspec 2 supports D0 D3 current D0
cap 05[80] = MSI supports 8 messages, 64 bit enabled with 1 message
none0@pci0:0:22:0: class=0x078000 rev=0x04 hdr=0x00 vendor=0x8086 device=0x8c3a subvendor=0x103c subdevice=0x21d0
vendor = 'Intel Corporation'
device = '8 Series/C220 Series Chipset Family MEI Controller'
class = simple comms
bar [10] = type Memory, range 64, base 0xf7c40000, size 16, enabled
cap 01[50] = powerspec 3 supports D0 D3 current D0
cap 05[8c] = MSI supports 1 message, 64 bit
uart2@pci0:0:22:3: class=0x070002 rev=0x04 hdr=0x00 vendor=0x8086 device=0x8c3d subvendor=0x103c subdevice=0x21d0
vendor = 'Intel Corporation'
device = '8 Series/C220 Series Chipset Family KT Controller'
class = simple comms
subclass = UART
bar [10] = type I/O Port, range 32, base 0xf0e0, size 8, enabled
bar [14] = type Memory, range 32, base 0xf7c3e000, size 4096, enabled
cap 01[c8] = powerspec 3 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit enabled with 1 message
em0@pci0:0:25:0: class=0x020000 rev=0x04 hdr=0x00 vendor=0x8086 device=0x153a subvendor=0x103c subdevice=0x21d0
vendor = 'Intel Corporation'
device = 'Ethernet Connection I217-LM'
class = network
subclass = ethernet
bar [10] = type Memory, range 32, base 0xf7c00000, size 131072, enabled
bar [14] = type Memory, range 32, base 0xf7c3d000, size 4096, enabled
bar [18] = type I/O Port, range 32, base 0xf080, size 32, enabled
cap 01[c8] = powerspec 2 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit enabled with 1 message
cap 13[e0] = PCI Advanced Features: FLR TP
ehci0@pci0:0:26:0: class=0x0c0320 rev=0x04 hdr=0x00 vendor=0x8086 device=0x8c2d subvendor=0x103c subdevice=0x21d0
vendor = 'Intel Corporation'
device = '8 Series/C220 Series Chipset Family USB EHCI'
class = serial bus
subclass = USB
bar [10] = type Memory, range 32, base 0xf7c3c000, size 1024, enabled
cap 01[50] = powerspec 2 supports D0 D3 current D0
cap 0a[58] = EHCI Debug Port at offset 0xa0 in map 0x14
cap 13[98] = PCI Advanced Features: FLR TP
hdac1@pci0:0:27:0: class=0x040300 rev=0x04 hdr=0x00 vendor=0x8086 device=0x8c20 subvendor=0x103c subdevice=0x21d0
vendor = 'Intel Corporation'
device = '8 Series/C220 Series Chipset High Definition Audio Controller'
class = multimedia
subclass = HDA
bar [10] = type Memory, range 64, base 0xf7c30000, size 16384, enabled
cap 01[50] = powerspec 2 supports D0 D3 current D0
cap 05[60] = MSI supports 1 message, 64 bit enabled with 1 message
cap 10[70] = PCI-Express 1 root endpoint max data 128(128) FLR NS
max read 128
ecap 0002[100] = VC 1 max VC1
pcib1@pci0:0:28:0: class=0x060400 rev=0xd4 hdr=0x01 vendor=0x8086 device=0x8c10 subvendor=0x103c subdevice=0x21d0
vendor = 'Intel Corporation'
device = '8 Series/C220 Series Chipset Family PCI Express Root Port'
class = bridge
subclass = PCI-PCI
cap 10[40] = PCI-Express 2 root port max data 128(128)
max read 128
link x0(x1) speed 0.0(5.0) ASPM L0s/L1(L0s/L1)
slot 0 power limit 0 mW HotPlug(empty) surprise
cap 05[80] = MSI supports 1 message
cap 0d[90] = PCI Bridge subvendor=0x103c subdevice=0x21d0
cap 01[a0] = powerspec 3 supports D0 D3 current D0
pcib2@pci0:0:28:4: class=0x060400 rev=0xd4 hdr=0x01 vendor=0x8086 device=0x8c18 subvendor=0x103c subdevice=0x21d0
vendor = 'Intel Corporation'
device = '8 Series/C220 Series Chipset Family PCI Express Root Port'
class = bridge
subclass = PCI-PCI
cap 10[40] = PCI-Express 2 root port max data 128(128)
max read 128
link x0(x4) speed 0.0(5.0) ASPM L0s/L1(L0s/L1)
slot 4 power limit 250 mW
cap 05[80] = MSI supports 1 message
cap 0d[90] = PCI Bridge subvendor=0x103c subdevice=0x21d0
cap 01[a0] = powerspec 3 supports D0 D3 current D0
ehci1@pci0:0:29:0: class=0x0c0320 rev=0x04 hdr=0x00 vendor=0x8086 device=0x8c26 subvendor=0x103c subdevice=0x21d0
vendor = 'Intel Corporation'
device = '8 Series/C220 Series Chipset Family USB EHCI'
class = serial bus
subclass = USB
bar [10] = type Memory, range 32, base 0xf7c3b000, size 1024, enabled
cap 01[50] = powerspec 2 supports D0 D3 current D0
cap 0a[58] = EHCI Debug Port at offset 0xa0 in map 0x14
cap 13[98] = PCI Advanced Features: FLR TP
isab0@pci0:0:31:0: class=0x060100 rev=0x04 hdr=0x00 vendor=0x8086 device=0x8c4c subvendor=0x103c subdevice=0x21d0
vendor = 'Intel Corporation'
device = 'Q85 Express LPC Controller'
class = bridge
subclass = PCI-ISA
cap 09[e0] = vendor (length 12) Intel cap 1 version 0
features: AMT, 4 PCI-e x1 slots
ahci0@pci0:0:31:2: class=0x010601 rev=0x04 hdr=0x00 vendor=0x8086 device=0x8c02 subvendor=0x103c subdevice=0x21d0
vendor = 'Intel Corporation'
device = '8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode]'
class = mass storage
subclass = SATA
bar [10] = type I/O Port, range 32, base 0xf0d0, size 8, enabled
bar [14] = type I/O Port, range 32, base 0xf0c0, size 4, enabled
bar [18] = type I/O Port, range 32, base 0xf0b0, size 8, enabled
bar [1c] = type I/O Port, range 32, base 0xf0a0, size 4, enabled
bar [20] = type I/O Port, range 32, base 0xf060, size 32, enabled
bar [24] = type Memory, range 32, base 0xf7c3a000, size 2048, enabled
cap 05[80] = MSI supports 1 message enabled with 1 message
cap 01[70] = powerspec 3 supports D0 D3 current D0
cap 12[a8] = SATA Index-Data Pair
ichsmb0@pci0:0:31:3: class=0x0c0500 rev=0x04 hdr=0x00 vendor=0x8086 device=0x8c22 subvendor=0x103c subdevice=0x21d0
vendor = 'Intel Corporation'
device = '8 Series/C220 Series Chipset Family SMBus Controller'
class = serial bus
subclass = SMBus
bar [10] = type Memory, range 64, base 0xf7c39000, size 256, enabled
bar [20] = type I/O Port, range 32, base 0xf040, size 32, enabled
sysctl_hw.model.out
(text/plain, 51 B)
hw.model: Intel(R) Pentium(R) CPU G3240T @ 2.70GHz
Xorg.0.log
(text/plain, 26.4 KB)
[ 11.994] X.Org X Server 1.20.14 X Protocol Version 11, Revision 0 [ 11.994] Build Operating System: FreeBSD 13.1-RELEASE-p2 amd64 [ 11.994] Current Operating System: FreeBSD ilargi 13.1-RELEASE FreeBSD 13.1-RELEASE releng/13.1-n250148-fc952ac2212 GENERIC amd64 [ 11.995] Build Date: 04 September 2022 10:47:59AM [ 11.995] [ 11.995] Current version of pixman: 0.40.0 [ 11.995] Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. [ 11.995] Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. [ 11.995] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Sep 21 15:47:27 2022 [ 11.997] (==) Using config directory: "/usr/local/etc/X11/xorg.conf.d" [ 11.997] (==) Using system config directory "/usr/local/share/X11/xorg.conf.d" [ 11.998] (==) No Layout section. Using the first Screen section. [ 11.998] (**) |-->Screen "Desktop" (0) [ 11.998] (**) | |-->Monitor "AOC X24P1" [ 11.999] (**) | |-->Device "Xeon E3-1200" [ 11.999] (==) Automatically adding devices [ 11.999] (==) Automatically enabling devices [ 11.999] (==) Not automatically adding GPU devices [ 11.999] (==) Max clients allowed: 256, resource mask: 0x1fffff [ 12.005] (WW) The directory "/usr/local/share/fonts/misc/" does not exist. [ 12.005] Entry deleted from font path. [ 12.005] (**) FontPath set to: /usr/local/share/fonts/TTF/, /usr/local/share/fonts/OTF/, /usr/local/share/fonts/dejavu/, /usr/local/share/fonts/Type1/, /usr/local/share/fonts/75dpi/, /usr/local/share/fonts/100dpi/, /usr/local/share/fonts/Droid/, /usr/local/share/fonts/webfonts/, /usr/local/share/fonts/cantarell/, /usr/local/share/fonts/ubuntu-font/, /usr/local/share/fonts/urwfonts-ttf/, /usr/local/share/fonts/bitstream-vera/, /usr/local/share/fonts/roboto-fonts-ttf/, /usr/local/share/fonts/Caladea/, /usr/local/share/fonts/Carlito/, /usr/local/share/fonts/Liberation/, /usr/local/share/fonts/GentiumBasic/, /usr/local/share/fonts/LinLibertineG/, /usr/local/share/fonts/TTF/, /usr/local/share/fonts/OTF/, /usr/local/share/fonts/Type1/, /usr/local/share/fonts/100dpi/, /usr/local/share/fonts/75dpi/, catalogue:/usr/local/etc/X11/fontpath.d [ 12.005] (**) ModulePath set to "/usr/local/lib/xorg/modules" [ 12.005] (II) The server relies on udev to provide the list of input devices. If no devices become available, reconfigure udev or disable AutoAddDevices. [ 12.005] (II) Loader magic: 0x433270 [ 12.005] (II) Module ABI versions: [ 12.005] X.Org ANSI C Emulation: 0.4 [ 12.005] X.Org Video Driver: 24.1 [ 12.005] X.Org XInput driver : 24.1 [ 12.005] X.Org Server Extension : 10.0 [ 12.005] (--) PCI:*(0@0:2:0) 8086:0402:103c:21d0 rev 6, Mem @ 0xf7800000/4194304, 0xe0000000/268435456, I/O @ 0x0000f000/64, BIOS @ 0x????????/65536 [ 12.006] (II) LoadModule: "glx" [ 12.006] (II) Loading /usr/local/lib/xorg/modules/extensions/libglx.so [ 12.019] (II) Module glx: vendor="X.Org Foundation" [ 12.019] compiled for 1.20.14, module version = 1.0.0 [ 12.019] ABI class: X.Org Server Extension, version 10.0 [ 12.019] (II) LoadModule: "modesetting" [ 12.019] (II) Loading /usr/local/lib/xorg/modules/drivers/modesetting_drv.so [ 12.020] (II) Module modesetting: vendor="X.Org Foundation" [ 12.020] compiled for 1.20.14, module version = 1.20.14 [ 12.020] Module class: X.Org Video Driver [ 12.020] ABI class: X.Org Video Driver, version 24.1 [ 12.020] (II) modesetting: Driver for Modesetting Kernel Drivers: kms [ 12.020] (--) Using syscons driver with X support (version 2.0) [ 12.020] (++) using VT number 9 [ 12.043] (**) modeset(0): claimed PCI slot 0@0:2:0 [ 12.043] (II) modeset(0): using default device [ 12.043] (WW) VGA arbiter: cannot open kernel arbiter, no multi-card support [ 12.043] (==) modeset(0): Depth 24, (==) framebuffer bpp 32 [ 12.043] (**) modeset(0): Option "AccelMethod" "UXA" [ 12.043] (==) modeset(0): RGB weight 888 [ 12.043] (==) modeset(0): Default visual is TrueColor [ 12.043] (**) modeset(0): glamor disabled [ 12.043] (II) modeset(0): ShadowFB: preferred YES, enabled YES [ 12.043] (II) modeset(0): Double-buffered shadow updates: off [ 12.044] (II) modeset(0): Output VGA-1 using monitor section AOC X24P1 [ 12.052] (II) modeset(0): Output DP-1 has no monitor section [ 12.053] (II) modeset(0): Output HDMI-1 has no monitor section [ 12.053] (II) modeset(0): Output DP-2 has no monitor section [ 12.054] (II) modeset(0): Output HDMI-2 has no monitor section [ 12.054] (II) modeset(0): EDID for output VGA-1 [ 12.063] (II) modeset(0): EDID for output DP-1 [ 12.063] (II) modeset(0): Manufacturer: AOC Model: 2401 Serial#: 40329 [ 12.063] (II) modeset(0): Year: 2018 Week: 37 [ 12.063] (II) modeset(0): EDID Version: 1.4 [ 12.063] (II) modeset(0): Digital Display Input [ 12.063] (II) modeset(0): 8 bits per channel [ 12.063] (II) modeset(0): Digital interface is DisplayPort [ 12.063] (II) modeset(0): Max Image Size [cm]: horiz.: 52 vert.: 32 [ 12.063] (II) modeset(0): Gamma: 2.20 [ 12.063] (II) modeset(0): DPMS capabilities: Off [ 12.063] (II) modeset(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 YCrCb 4:2:2 [ 12.063] (II) modeset(0): First detailed timing is preferred mode [ 12.063] (II) modeset(0): Preferred mode is native pixel format and refresh rate [ 12.063] (II) modeset(0): redX: 0.653 redY: 0.338 greenX: 0.308 greenY: 0.626 [ 12.063] (II) modeset(0): blueX: 0.146 blueY: 0.054 whiteX: 0.313 whiteY: 0.329 [ 12.063] (II) modeset(0): Supported established timings: [ 12.063] (II) modeset(0): 720x400@70Hz [ 12.063] (II) modeset(0): 640x480@60Hz [ 12.063] (II) modeset(0): 640x480@67Hz [ 12.063] (II) modeset(0): 640x480@72Hz [ 12.063] (II) modeset(0): 640x480@75Hz [ 12.063] (II) modeset(0): 800x600@56Hz [ 12.063] (II) modeset(0): 800x600@60Hz [ 12.063] (II) modeset(0): 800x600@72Hz [ 12.063] (II) modeset(0): 800x600@75Hz [ 12.063] (II) modeset(0): 832x624@75Hz [ 12.063] (II) modeset(0): 1024x768@60Hz [ 12.063] (II) modeset(0): 1024x768@70Hz [ 12.063] (II) modeset(0): 1024x768@75Hz [ 12.063] (II) modeset(0): 1280x1024@75Hz [ 12.063] (II) modeset(0): Manufacturer's mask: 0 [ 12.063] (II) modeset(0): Supported standard timings: [ 12.063] (II) modeset(0): #0: hsize: 1920 vsize 1080 refresh: 60 vid: 49361 [ 12.063] (II) modeset(0): #1: hsize: 1680 vsize 1050 refresh: 60 vid: 179 [ 12.063] (II) modeset(0): #2: hsize: 1440 vsize 900 refresh: 60 vid: 149 [ 12.063] (II) modeset(0): #3: hsize: 1280 vsize 1024 refresh: 60 vid: 32897 [ 12.063] (II) modeset(0): #4: hsize: 1280 vsize 960 refresh: 60 vid: 16513 [ 12.063] (II) modeset(0): #5: hsize: 1280 vsize 720 refresh: 60 vid: 49281 [ 12.063] (II) modeset(0): Supported detailed timing: [ 12.063] (II) modeset(0): clock: 154.0 MHz Image Size: 518 x 324 mm [ 12.063] (II) modeset(0): h_active: 1920 h_sync: 1968 h_sync_end 2000 h_blank_end 2080 h_border: 0 [ 12.063] (II) modeset(0): v_active: 1200 v_sync: 1203 v_sync_end 1209 v_blanking: 1235 v_border: 0 [ 12.063] (II) modeset(0): Serial No: GMBJ9HA040329 [ 12.063] (II) modeset(0): Monitor name: 24P1X [ 12.063] (II) modeset(0): Ranges: V min: 50 V max: 76 Hz, H min: 30 H max: 83 kHz, PixClock max 175 MHz [ 12.063] (II) modeset(0): Supported detailed timing: [ 12.063] (II) modeset(0): clock: 148.5 MHz Image Size: 518 x 324 mm [ 12.063] (II) modeset(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0 [ 12.063] (II) modeset(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0 [ 12.063] (II) modeset(0): Supported detailed timing: [ 12.063] (II) modeset(0): clock: 74.2 MHz Image Size: 518 x 324 mm [ 12.063] (II) modeset(0): h_active: 1280 h_sync: 1390 h_sync_end 1430 h_blank_end 1650 h_border: 0 [ 12.063] (II) modeset(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0 [ 12.063] (II) modeset(0): Supported detailed timing: [ 12.063] (II) modeset(0): clock: 27.0 MHz Image Size: 518 x 324 mm [ 12.063] (II) modeset(0): h_active: 720 h_sync: 736 h_sync_end 798 h_blank_end 858 h_border: 0 [ 12.063] (II) modeset(0): v_active: 480 v_sync: 489 v_sync_end 495 v_blanking: 525 v_border: 0 [ 12.063] (II) modeset(0): Supported detailed timing: [ 12.063] (II) modeset(0): clock: 27.0 MHz Image Size: 518 x 324 mm [ 12.063] (II) modeset(0): h_active: 720 h_sync: 732 h_sync_end 796 h_blank_end 864 h_border: 0 [ 12.063] (II) modeset(0): v_active: 576 v_sync: 581 v_sync_end 586 v_blanking: 625 v_border: 0 [ 12.063] (II) modeset(0): Number of EDID sections to follow: 1 [ 12.063] (II) modeset(0): EDID (in hex): [ 12.063] (II) modeset(0): 00ffffffffffff0005e30124899d0000 [ 12.063] (II) modeset(0): 251c0104a53420783a6d75a7564ea025 [ 12.063] (II) modeset(0): 0d5054bfef00d1c0b300950081808140 [ 12.063] (II) modeset(0): 81c001010101283c80a070b023403020 [ 12.063] (II) modeset(0): 360006442100001a000000ff00474d42 [ 12.063] (II) modeset(0): 4a394841303430333239000000fc0032 [ 12.063] (II) modeset(0): 345031580a20202020202020000000fd [ 12.063] (II) modeset(0): 00324c1e5311010a202020202020019e [ 12.063] (II) modeset(0): 02031ef14b901f051404130312021101 [ 12.063] (II) modeset(0): 230907078301000065030c001000023a [ 12.063] (II) modeset(0): 801871382d40582c450006442100001e [ 12.063] (II) modeset(0): 011d007251d01e206e28550006442100 [ 12.063] (II) modeset(0): 001e8c0ad08a20e02d10103e96000644 [ 12.063] (II) modeset(0): 210000188c0ad090204031200c405500 [ 12.063] (II) modeset(0): 06442100001800000000000000000000 [ 12.063] (II) modeset(0): 00000000000000000000000000000059 [ 12.063] (II) modeset(0): Printing probed modes for output DP-1 [ 12.063] (II) modeset(0): Modeline "1920x1200"x60.0 154.00 1920 1968 2000 2080 1200 1203 1209 1235 +hsync -vsync (74.0 kHz eP) [ 12.063] (II) modeset(0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz e) [ 12.063] (II) modeset(0): Modeline "1920x1080"x50.0 148.50 1920 2448 2492 2640 1080 1084 1089 1125 +hsync +vsync (56.2 kHz e) [ 12.063] (II) modeset(0): Modeline "1920x1080"x59.9 148.35 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.4 kHz e) [ 12.063] (II) modeset(0): Modeline "1920x1080i"x60.0 74.25 1920 2008 2052 2200 1080 1084 1094 1125 interlace +hsync +vsync (33.8 kHz e) [ 12.063] (II) modeset(0): Modeline "1920x1080i"x50.0 74.25 1920 2448 2492 2640 1080 1084 1094 1125 interlace +hsync +vsync (28.1 kHz e) [ 12.063] (II) modeset(0): Modeline "1920x1080i"x59.9 74.18 1920 2008 2052 2200 1080 1084 1094 1125 interlace +hsync +vsync (33.7 kHz e) [ 12.063] (II) modeset(0): Modeline "1680x1050"x60.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz e) [ 12.063] (II) modeset(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e) [ 12.063] (II) modeset(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e) [ 12.063] (II) modeset(0): Modeline "1440x900"x59.9 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz e) [ 12.063] (II) modeset(0): Modeline "1280x960"x60.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e) [ 12.063] (II) modeset(0): Modeline "1280x720"x60.0 74.25 1280 1390 1430 1650 720 725 730 750 +hsync +vsync (45.0 kHz e) [ 12.063] (II) modeset(0): Modeline "1280x720"x50.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz e) [ 12.063] (II) modeset(0): Modeline "1280x720"x59.9 74.18 1280 1390 1430 1650 720 725 730 750 +hsync +vsync (45.0 kHz e) [ 12.063] (II) modeset(0): Modeline "1024x768"x75.0 78.75 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.0 kHz e) [ 12.063] (II) modeset(0): Modeline "1024x768"x70.1 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e) [ 12.063] (II) modeset(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e) [ 12.063] (II) modeset(0): Modeline "832x624"x74.6 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e) [ 12.063] (II) modeset(0): Modeline "800x600"x72.2 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e) [ 12.063] (II) modeset(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e) [ 12.063] (II) modeset(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e) [ 12.063] (II) modeset(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e) [ 12.063] (II) modeset(0): Modeline "720x576"x50.0 27.00 720 732 796 864 576 581 586 625 -hsync -vsync (31.2 kHz e) [ 12.063] (II) modeset(0): Modeline "720x480"x60.0 27.03 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz e) [ 12.063] (II) modeset(0): Modeline "720x480"x59.9 27.00 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz e) [ 12.063] (II) modeset(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e) [ 12.063] (II) modeset(0): Modeline "640x480"x72.8 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz e) [ 12.063] (II) modeset(0): Modeline "640x480"x66.7 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e) [ 12.063] (II) modeset(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e) [ 12.063] (II) modeset(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e) [ 12.063] (II) modeset(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e) [ 12.064] (II) modeset(0): EDID for output HDMI-1 [ 12.064] (II) modeset(0): EDID for output DP-2 [ 12.065] (II) modeset(0): EDID for output HDMI-2 [ 12.065] (II) modeset(0): Output VGA-1 disconnected [ 12.065] (II) modeset(0): Output DP-1 connected [ 12.065] (II) modeset(0): Output HDMI-1 disconnected [ 12.065] (II) modeset(0): Output DP-2 disconnected [ 12.065] (II) modeset(0): Output HDMI-2 disconnected [ 12.065] (II) modeset(0): Using exact sizes for initial modes [ 12.065] (II) modeset(0): Output DP-1 using initial mode 1920x1200 +0+0 [ 12.065] (==) modeset(0): Using gamma correction (1.0, 1.0, 1.0) [ 12.065] (==) modeset(0): DPI set to (96, 96) [ 12.065] (II) Loading sub module "fb" [ 12.065] (II) LoadModule: "fb" [ 12.065] (II) Loading /usr/local/lib/xorg/modules/libfb.so [ 12.066] (II) Module fb: vendor="X.Org Foundation" [ 12.066] compiled for 1.20.14, module version = 1.0.0 [ 12.066] ABI class: X.Org ANSI C Emulation, version 0.4 [ 12.066] (II) Loading sub module "shadow" [ 12.066] (II) LoadModule: "shadow" [ 12.066] (II) Loading /usr/local/lib/xorg/modules/libshadow.so [ 12.066] (II) Module shadow: vendor="X.Org Foundation" [ 12.066] compiled for 1.20.14, module version = 1.1.0 [ 12.066] ABI class: X.Org ANSI C Emulation, version 0.4 [ 12.077] (==) modeset(0): Backing store enabled [ 12.077] (==) modeset(0): Silken mouse enabled [ 12.161] (II) modeset(0): Initializing kms color map for depth 24, 8 bpc. [ 12.161] (==) modeset(0): DPMS enabled [ 12.161] (WW) modeset(0): Option "DRI" is not used [ 12.161] (II) Initializing extension Generic Event Extension [ 12.161] (II) Initializing extension SHAPE [ 12.161] (II) Initializing extension MIT-SHM [ 12.162] (II) Initializing extension XInputExtension [ 12.162] (II) Initializing extension XTEST [ 12.162] (II) Initializing extension BIG-REQUESTS [ 12.163] (II) Initializing extension SYNC [ 12.163] (II) Initializing extension XKEYBOARD [ 12.163] (II) Initializing extension XC-MISC [ 12.164] (II) Initializing extension SECURITY [ 12.164] (II) Initializing extension XFIXES [ 12.164] (II) Initializing extension RENDER [ 12.164] (II) Initializing extension RANDR [ 12.165] (II) Initializing extension COMPOSITE [ 12.165] (II) Initializing extension DAMAGE [ 12.165] (II) Initializing extension MIT-SCREEN-SAVER [ 12.165] (II) Initializing extension DOUBLE-BUFFER [ 12.165] (II) Initializing extension RECORD [ 12.166] (II) Initializing extension DPMS [ 12.166] (II) Initializing extension Present [ 12.166] (II) Initializing extension DRI3 [ 12.166] (II) Initializing extension X-Resource [ 12.166] (II) Initializing extension XVideo [ 12.167] (II) Initializing extension XVideo-MotionCompensation [ 12.167] (II) Initializing extension GLX [ 12.167] (II) AIGLX: Screen 0 is not DRI2 capable [ 12.461] (II) IGLX: Loaded and initialized swrast [ 12.461] (II) GLX: Initialized DRISWRAST GL provider for screen 0 [ 12.461] (II) Initializing extension XFree86-VidModeExtension [ 12.462] (II) Initializing extension XFree86-DGA [ 12.462] (II) Initializing extension XFree86-DRI [ 12.462] (II) Initializing extension DRI2 [ 12.462] (II) modeset(0): Damage tracking initialized [ 12.462] (II) modeset(0): Setting screen physical size to 508 x 317 [ 12.515] (II) config/udev: Adding input device System mouse (/dev/input/event0) [ 12.515] (**) System mouse: Applying InputClass "libinput pointer catchall" [ 12.515] (II) LoadModule: "libinput" [ 12.515] (II) Loading /usr/local/lib/xorg/modules/input/libinput_drv.so [ 12.520] (II) Module libinput: vendor="X.Org Foundation" [ 12.520] compiled for 1.20.14, module version = 1.2.0 [ 12.520] Module class: X.Org XInput Driver [ 12.520] ABI class: X.Org XInput driver, version 24.1 [ 12.520] (II) Using input driver 'libinput' for 'System mouse' [ 12.520] (**) System mouse: always reports core events [ 12.520] (**) Option "Device" "/dev/input/event0" [ 12.521] (**) Option "_source" "server/udev" [ 12.528] (II) event0 - System mouse: is tagged by udev as: Mouse [ 12.529] (II) event0 - System mouse: device is a pointer [ 12.530] (II) event0 - System mouse: device removed [ 12.530] (**) Option "config_info" "udev:/dev/input/event0" [ 12.530] (II) XINPUT: Adding extended input device "System mouse" (type: MOUSE, id 6) [ 12.530] (**) Option "AccelerationScheme" "none" [ 12.530] (**) System mouse: (accel) selected scheme none/0 [ 12.530] (**) System mouse: (accel) acceleration factor: 2.000 [ 12.530] (**) System mouse: (accel) acceleration threshold: 4 [ 12.532] (II) event0 - System mouse: is tagged by udev as: Mouse [ 12.533] (II) event0 - System mouse: device is a pointer [ 12.533] (II) config/udev: Adding input device System keyboard multiplexer (/dev/input/event1) [ 12.533] (**) System keyboard multiplexer: Applying InputClass "Evdev keyboard" [ 12.533] (**) System keyboard multiplexer: Applying InputClass "libinput keyboard catchall" [ 12.533] (**) System keyboard multiplexer: Applying InputClass "Keyboard" [ 12.533] (II) LoadModule: "kbd" [ 12.534] (WW) Warning, couldn't open module kbd [ 12.534] (EE) Failed to load module "kbd" (module does not exist, 0) [ 12.534] (EE) No input driver matching `kbd' [ 12.534] (II) Falling back to input driver `libinput' [ 12.534] (II) Using input driver 'libinput' for 'System keyboard multiplexer' [ 12.534] (**) System keyboard multiplexer: always reports core events [ 12.534] (**) Option "Device" "/dev/input/event1" [ 12.534] (**) Option "_source" "server/udev" [ 12.535] (II) event1 - System keyboard multiplexer: is tagged by udev as: Keyboard [ 12.535] (II) event1 - System keyboard multiplexer: device is a keyboard [ 12.537] (II) event1 - System keyboard multiplexer: device removed [ 12.537] (**) Option "config_info" "udev:/dev/input/event1" [ 12.537] (II) XINPUT: Adding extended input device "System keyboard multiplexer" (type: KEYBOARD, id 7) [ 12.537] (**) Option "xkb_rules" "evdev" [ 12.537] (**) Option "xkb_layout" "fr" [ 12.537] (**) Option "xkb_variant" "oss" [ 12.537] (**) Option "xkb_options" "terminate:ctrl_alt_bksp" [ 12.564] (II) event1 - System keyboard multiplexer: is tagged by udev as: Keyboard [ 12.564] (II) event1 - System keyboard multiplexer: device is a keyboard [ 12.565] (II) config/udev: Adding input device Power Button (/dev/input/event2) [ 12.565] (**) Power Button: Applying InputClass "Evdev keyboard" [ 12.565] (**) Power Button: Applying InputClass "libinput keyboard catchall" [ 12.565] (**) Power Button: Applying InputClass "Keyboard" [ 12.565] (II) LoadModule: "kbd" [ 12.566] (WW) Warning, couldn't open module kbd [ 12.566] (EE) Failed to load module "kbd" (module does not exist, 0) [ 12.566] (EE) No input driver matching `kbd' [ 12.566] (II) Falling back to input driver `libinput' [ 12.566] (II) Using input driver 'libinput' for 'Power Button' [ 12.566] (**) Power Button: always reports core events [ 12.566] (**) Option "Device" "/dev/input/event2" [ 12.566] (**) Option "_source" "server/udev" [ 12.567] (II) event2 - Power Button: is tagged by udev as: Keyboard [ 12.567] (II) event2 - Power Button: device is a keyboard [ 12.568] (II) event2 - Power Button: device removed [ 12.568] (**) Option "config_info" "udev:/dev/input/event2" [ 12.568] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8) [ 12.568] (**) Option "xkb_rules" "evdev" [ 12.568] (**) Option "xkb_layout" "fr" [ 12.568] (**) Option "xkb_variant" "oss" [ 12.568] (**) Option "xkb_options" "terminate:ctrl_alt_bksp" [ 12.570] (II) event2 - Power Button: is tagged by udev as: Keyboard [ 12.570] (II) event2 - Power Button: device is a keyboard [ 12.571] (II) config/udev: Adding input device AT keyboard (/dev/input/event3) [ 12.571] (**) AT keyboard: Applying InputClass "Evdev keyboard" [ 12.571] (**) AT keyboard: Applying InputClass "libinput keyboard catchall" [ 12.571] (**) AT keyboard: Applying InputClass "Keyboard" [ 12.571] (II) LoadModule: "kbd" [ 12.571] (WW) Warning, couldn't open module kbd [ 12.571] (EE) Failed to load module "kbd" (module does not exist, 0) [ 12.571] (EE) No input driver matching `kbd' [ 12.571] (II) Falling back to input driver `libinput' [ 12.571] (II) Using input driver 'libinput' for 'AT keyboard' [ 12.571] (**) AT keyboard: always reports core events [ 12.571] (**) Option "Device" "/dev/input/event3" [ 12.571] (**) Option "_source" "server/udev" [ 12.573] (II) event3 - AT keyboard: is tagged by udev as: Keyboard [ 12.573] (II) event3 - AT keyboard: device is a keyboard [ 12.575] (II) event3 - AT keyboard: device removed [ 12.575] (**) Option "config_info" "udev:/dev/input/event3" [ 12.575] (II) XINPUT: Adding extended input device "AT keyboard" (type: KEYBOARD, id 9) [ 12.576] (**) Option "xkb_rules" "evdev" [ 12.576] (**) Option "xkb_layout" "fr" [ 12.576] (**) Option "xkb_variant" "oss" [ 12.576] (**) Option "xkb_options" "terminate:ctrl_alt_bksp" [ 12.577] (II) event3 - AT keyboard: is tagged by udev as: Keyboard [ 12.577] (II) event3 - AT keyboard: device is a keyboard [ 12.580] (II) config/udev: Adding input device vendor 0x04d9 USB Keyboard (/dev/input/event4) [ 12.580] (**) vendor 0x04d9 USB Keyboard: Applying InputClass "Evdev keyboard" [ 12.580] (**) vendor 0x04d9 USB Keyboard: Applying InputClass "libinput keyboard catchall" [ 12.580] (**) vendor 0x04d9 USB Keyboard: Applying InputClass "Keyboard" [ 12.580] (II) LoadModule: "kbd" [ 12.580] (WW) Warning, couldn't open module kbd [ 12.580] (EE) Failed to load module "kbd" (module does not exist, 0) [ 12.580] (EE) No input driver matching `kbd' [ 12.580] (II) Falling back to input driver `libinput' [ 12.580] (II) Using input driver 'libinput' for 'vendor 0x04d9 USB Keyboard' [ 12.580] (**) vendor 0x04d9 USB Keyboard: always reports core events [ 12.580] (**) Option "Device" "/dev/input/event4" [ 12.580] (**) Option "_source" "server/udev" [ 12.582] (II) event4 - vendor 0x04d9 USB Keyboard, class 0/0, rev 1.10/3.10, addr 2: is tagged by udev as: Keyboard [ 12.582] (II) event4 - vendor 0x04d9 USB Keyboard, class 0/0, rev 1.10/3.10, addr 2: device is a keyboard [ 12.584] (II) event4 - vendor 0x04d9 USB Keyboard, class 0/0, rev 1.10/3.10, addr 2: device removed [ 12.584] (**) Option "config_info" "udev:/dev/input/event4" [ 12.584] (II) XINPUT: Adding extended input device "vendor 0x04d9 USB Keyboard" (type: KEYBOARD, id 10) [ 12.584] (**) Option "xkb_rules" "evdev" [ 12.584] (**) Option "xkb_layout" "fr" [ 12.584] (**) Option "xkb_variant" "oss" [ 12.584] (**) Option "xkb_options" "terminate:ctrl_alt_bksp" [ 12.585] (II) event4 - vendor 0x04d9 USB Keyboard, class 0/0, rev 1.10/3.10, addr 2: is tagged by udev as: Keyboard [ 12.586] (II) event4 - vendor 0x04d9 USB Keyboard, class 0/0, rev 1.10/3.10, addr 2: device is a keyboard [ 12.588] (II) config/udev: Adding input device Logitech USB Optical Mouse (/dev/input/event5) [ 12.588] (**) Logitech USB Optical Mouse: Applying InputClass "libinput pointer catchall" [ 12.588] (II) Using input driver 'libinput' for 'Logitech USB Optical Mouse' [ 12.588] (**) Logitech USB Optical Mouse: always reports core events [ 12.588] (**) Option "Device" "/dev/input/event5" [ 12.588] (**) Option "_source" "server/udev" [ 12.589] (II) event5 - Logitech USB Optical Mouse, class 0/0, rev 2.00/72.00, addr 3: is tagged by udev as: Mouse [ 12.590] (II) event5 - Logitech USB Optical Mouse, class 0/0, rev 2.00/72.00, addr 3: device is a pointer [ 12.591] (II) event5 - Logitech USB Optical Mouse, class 0/0, rev 2.00/72.00, addr 3: device removed [ 12.591] (**) Option "config_info" "udev:/dev/input/event5" [ 12.591] (II) XINPUT: Adding extended input device "Logitech USB Optical Mouse" (type: MOUSE, id 11) [ 12.591] (**) Option "AccelerationScheme" "none" [ 12.591] (**) Logitech USB Optical Mouse: (accel) selected scheme none/0 [ 12.591] (**) Logitech USB Optical Mouse: (accel) acceleration factor: 2.000 [ 12.591] (**) Logitech USB Optical Mouse: (accel) acceleration threshold: 4 [ 12.593] (II) event5 - Logitech USB Optical Mouse, class 0/0, rev 2.00/72.00, addr 3: is tagged by udev as: Mouse [ 12.594] (II) event5 - Logitech USB Optical Mouse, class 0/0, rev 2.00/72.00, addr 3: device is a pointer