Intel L440GX+ and SMP config

Hi everybody,
I'm new to UNIX and NetBSD in general.  I'm trying to configure a MP kernel on an L440GX+ Intel motherboard.  I'vetried using the MPBIOS option as well as the MPACPI option respectively with the same result.  I used the cpu* at mainbus? option both times and the ioapic* at mainbus? apid? option when I used MPACPI.  These are all set in the "GENERIC" config file (I renamed mine AOXOMOXOA) and commented out of GENERIC.MP (which I renamed AOXOMOXOA.MP).  I ftp'd the source tree before configuring, built the tools, etc. and did ./build.sh kernel=AOXOMOXOA.MP from /usr/src - which completes without errors.  I rename and mv the new kernel to /, renaming the old one to netbsd.old and reboot.  The dmesg output below is what I get regardless of whether I use MPBIOS or MPACPI. 

cpu1: starting - but at the end it says cpu failed to start

Any ideas?  This mb would only run FreeBSD-5.0-DP1 smp, other than that, nothing, in fact it would lock up bootingFreeBSD-5.0-release at the point where it waits for scsi devices to settle.  Never had any luck with 4.7 or 4.8 release from FreeBSD either, with pretty much the same outcome.  

NetBSD 1.6R (AOXOMOXOA.MP) #1: Thu May  1 22:54:52 EDT 2003
	[email protected]:/usr/src/sys/arch/i386/compile/AOXOMOXOA.MP
total memory = 287 MB
avail memory = 259 MB
using 3706 buffers containing 14824 KB of memory
BIOS32 rev. 0 found at 0xfd7e3
mainbus0 (root)
mainbus0: Intel MP Specification (Version 1.4) (INTEL    Lancewood   )
cpu0 at mainbus0: apid 1 (boot processor)
cpu0: Intel Pentium III (686-class), 447.72 MHz, id 0x673
cpu0: features 387fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features 387fbff<PGE,MCA,CMOV,PAT,PSE36,PN,MMX>
cpu0: features 387fbff<FXSR,SSE>
cpu0: I-cache 16 KB 32b/line 4-way, D-cache 16 KB 32b/line 4-way
cpu0: L2 cache 512 KB 32b/line 4-way
cpu0: ITLB 32 4 KB entries 4-way, 2 4 MB entries fully associative
cpu0: DTLB 64 4 KB entries 4-way, 8 4 MB entries 4-way
cpu0: serial number 0000-0673-0003-B3DF-7BBF-D7B1
cpu0: calibrating local timer
cpu0: apic clock running at 99 MHz
cpu0: 32 page colors
cpu1 at mainbus0: apid 0 (application processor)
cpu1: starting
cpu1: Intel Pentium III (686-class), 447.69 MHz, id 0x673
cpu1: features 387fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu1: features 387fbff<PGE,MCA,CMOV,PAT,PSE36,PN,MMX>
cpu1: features 387fbff<FXSR,SSE>
cpu1: I-cache 16 KB 32b/line 4-way, D-cache 16 KB 32b/line 4-way
cpu1: L2 cache 512 KB 32b/line 4-way
cpu1: ITLB 32 4 KB entries 4-way, 2 4 MB entries fully associative
cpu1: DTLB 64 4 KB entries 4-way, 8 4 MB entries 4-way
cpu1: serial number 0000-0673-0002-A334-8E6C-0D6D
mpbios: bus 0 is type PCI   
mpbios: bus 1 is type PCI   
mpbios: bus 2 is type PCI   
mpbios: bus 3 is type ISA   
ioapic0 at mainbus0 apid 2 (I/O APIC)
ioapic0: pa 0xfec00000, version 11, 24 pins
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82443GX Host Bridge/Controller (rev. 0x00)
agp0 at pchb0: aperture at 0xf8000000, size 0x4000000
ppb0 at pci0 dev 1 function 0: Intel 82443GX AGP Interface (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
ppb1 at pci1 dev 15 function 0: Digital Equipment product 0x0023 (rev. 0x06)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
ahc1 at pci0 dev 12 function 0
ahc1: interrupting at apic 2 int 19 (irq 11)
ahc1: aic7896/97: Ultra2 Wide Channel A, SCSI Id=6, 32/253 SCBs
scsibus0 at ahc1: 16 targets, 8 luns per target
ahc2 at pci0 dev 12 function 1
ahc2: interrupting at apic 2 int 19 (irq 11)
ahc2: aic7896/97: Ultra2 Wide Channel B, SCSI Id=7, 32/253 SCBs
scsibus1 at ahc2: 16 targets, 8 luns per target
fxp0 at pci0 dev 14 function 0: i82559 Ethernet, rev 8
fxp0: interrupting at apic 2 int 21 (irq 10)
fxp0: Ethernet address 00:a0:c9:fc:29:5c
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib0 at pci0 dev 18 function 0
pcib0: Intel 82371AB PCI-to-ISA Bridge (PIIX4) (rev. 0x02)
pciide0 at pci0 dev 18 function 1: Intel 82371AB IDE controller (PIIX4) (rev. 0x01)
pciide0: bus-master DMA support present
pciide0: primary channel wired to compatibility mode
pciide0: disabling primary channel (no drives)
pciide0: secondary channel wired to compatibility mode
pciide0: disabling secondary channel (no drives)
uhci0 at pci0 dev 18 function 2: Intel 82371AB USB Host Controller (PIIX4) (rev. 0x01)
uhci0: interrupting at apic 2 int 21 (irq 10)
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
Intel 82371AB Power Management Controller (PIIX4) (miscellaneous bridge, revision 0x02) at pci0 dev 18 function 3 not configured
vga1 at pci0 dev 20 function 0: Cirrus Logic CL-GD5480 (rev. 0x23)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
isapnp0: no ISA Plug 'n Play devices found
ioapic0: enabling
Kernelized RAIDframe activated
scsibus0: waiting 2 seconds for devices to settle...
scsibus1: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 0 lun 0: <SEAGATE, ST39102LCSUN9.0G, 0828> disk fixed
sd0: 8637 MB, 4926 cyl, 27 head, 133 sec, 512 bytes/sect x 17689267 sectors
sd0: sync (25.00ns offset 15), 16-bit (80.000MB/s) transfers, tagged queueing
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs
cpu failed to start
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
ftpd (pid 1407) changing logname from bob to ftp
ftpd (pid 1431) changing logname from ftp to bob