Re: adding support for new PHY?

Johan A. van Zanten <[email protected]> wrote:
> 
> > Johan A. van Zanten <[email protected]> writes:
> > >  I built a new kernel with:
> > >
> > >      rgephy* at mii? phy ?
> > >  And it is recognized during the boot:
> > >
> > > re0 at pci0 dev 14 function 0: RealTek 8169S Single-chip Gigabit Ethernet
> > > re0: interrupting at dec 6600 irq 35
> > > re0: Ethernet address 00:e0:4c:77:79:80
> > > re0: using 512 tx descriptors
> > > rgephy0 at re0 phy 7: RTL8169S/8110S 1000BASE-T media interface, rev. 0
> > >
> > >  But i can't get it to work (via 'ifconfig re0 media 100baseTX mediaopt
> > > full-duplex' for example) with the switch at anything other than 10baseT.
> 
> "Perry E. Metzger" <[email protected]> wrote:
> > 
> > Generally speaking, gig e switches demand that you autonegotiate. Try
> > it again with autonegotiation instead of nailing it.
> 
>  If i set the switch to "auto" and do:
> 
>   ifconfig re0 media autoselect
> 
> ...then i get 10 Mbps half-duplex.
> 
> I even rebooted the machine to see.  Without me issuing any (manual)
> ifconfig commands, here's what the interface looks like:
> 
> sarasvati:/root # ifconfig re0
> re0: flags=8a02<BROADCAST,ALLMULTI,SIMPLEX,MULTICAST> mtu 1500
>         capabilities=87<IP4CSUM,TCP4CSUM,UDP4CSUM,TSO4>
>         enabled=0
>         address: 00:e0:4c:77:79:80
>         media: Ethernet autoselect (10baseT)
>         status: active


 OK, my apologies for not being more thorough before posting -- the
store-bought (not home-made) cable i was using with the card seems to have
been the problem.  I got another CAT 5E cable today, and when i plug it
in, success!:

sarasvati:/tew/001/rdist # ifconfig re0 
re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
        capabilities=87<IP4CSUM,TCP4CSUM,UDP4CSUM,TSO4>
        enabled=0
        address: 00:e0:4c:77:79:80
        media: Ethernet autoselect (1000baseT full-duplex)
        status: active
        inet 192.168.100.99 netmask 0xffffff00 broadcast 192.168.100.255
        inet6 fe80::2e0:4cff:fe77:7980%re0 prefixlen 64 scopeid 0x3


From /var/run/dmesg:

re0 at pci0 dev 14 function 0: RealTek 8169S Single-chip Gigabit Ethernet
re0: interrupting at dec 6600 irq 35
re0: Ethernet address 00:e0:4c:77:79:80
re0: using 512 tx descriptors
rgephy0 at re0 phy 7: RTL8169S/8110S 1000BASE-T media interface, rev. 0
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto


I think the problem i was having with the other machine (and a home-made
cable) was related to using ukphy instead of rgephy.

Thanks for your help, as well as the others!

 -johan