Re: Possible fix for DEC 2000 / Jensen

Hi,

> First of all thanks for committing the patch and there is still hope that
> the Jensen will ever run NetBSD :)
> I have tried to boot the latest snapshot, but it still hangs  at the same
> point.

Umm, bad news..

> Full log attached.
> 
> [   1.0000000] vga0 at isa0 port 0x3b0-0x3df iomem 0xa0000-0xbffff
> [   1.0000000] wsdisplay0 at vga0 (kbdmux ignored)
> [   1.0000000] fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
> 
> As always I am ready to test anything as it is sitting below my desk.

I wonder when COM_REG_MCR is written on startup because
cominit() doesn't refer sc->sc_mcr on writing COM_REG_MCR
(because it's called from early cninit).
 https://nxr.netbsd.org/xref/src/sys/dev/ic/com.c?r=1.359#2461

Could you try the following patch?
(if you need a pre-build kernel please let me know)

Index: sys/arch/alpha/jensenio/com_jensenio.c
===================================================================
RCS file: /cvsroot/src/sys/arch/alpha/jensenio/com_jensenio.c,v
retrieving revision 1.16
diff -u -p -d -r1.16 com_jensenio.c
--- sys/arch/alpha/jensenio/com_jensenio.c	19 Sep 2020 16:54:34 -0000	1.16
+++ sys/arch/alpha/jensenio/com_jensenio.c	22 Sep 2020 15:56:05 -0000
@@ -93,6 +93,7 @@ com_jensenio_attach(device_t parent, dev
 	struct com_jensenio_softc *jsc = device_private(self);
 	struct com_softc *sc = &jsc->sc_com;
 	struct jensenio_attach_args *ja = aux;
+	struct com_regs *regsp = &sc->sc_regs;
 	bus_space_handle_t ioh;
 
 	sc->sc_dev = self;
@@ -102,7 +103,7 @@ com_jensenio_attach(device_t parent, dev
 		aprint_error(": can't map i/o space\n");
 		return;
 	}
-	com_init_regs(&sc->sc_regs, ja->ja_iot, ioh, ja->ja_ioaddr);
+	com_init_regs(regsp, ja->ja_iot, ioh, ja->ja_ioaddr);
 
 	sc->sc_frequency = COM_FREQ;
 
@@ -110,11 +111,13 @@ com_jensenio_attach(device_t parent, dev
 	 * According to comments in Linux drivers/tty/serial/8250/8250.h,
 	 * the driver has to set OUT1 and OUT2 lines for "some ALPHA"
 	 * otherwise "the machine locks up with endless interrupts."
-	 * Note OUT2 (MCR_IENABLE) is set in MI com_attach_subr()
-	 * so we have to set OUT1 (MCR_DSR) in the MD attachment.
+	 * Note OUT2 (MCR_IENABLE) is also set in MI com_attach_subr()
+	 * but we have to set them before interrupts are enabled.
 	 * See also PR/36628.
 	 */
-	SET(sc->sc_mcr, MCR_DRS);
+	SET(sc->sc_mcr, MCR_DRS | MCR_IENABLE);
+	bus_space_write_1(regsp->cr_iot, regsp->cr_ioh,
+	    regsp->cr_map[COM_REG_MCR], sc->sc_mcr);
 
 	com_attach_subr(sc);
 


Thanks,

---
Izumi Tsutsui