Tyne boots into single user

Hi,

I've committed several fixes for DeskStation Tyne support
and now it boots into single user. (dmesg attached)

Many thanks to TAKEUCHI Yoji for providing the Tyne board.
---
Izumi Tsutsui
[email protected]

---
Initialize Tyne RISC PC
Initialize LogiCore Chip Set
Copy C code from EPROM to memory
Jump into C code
80000278
800FFFFC
30410000
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.6T (GRANDIS) #31: Sun Jun 15 07:14:29 JST 2003
	tsutsui@mirage:/usr/src/sys/arch/arc/compile/GRANDIS
DESKTECH DeskStation Tyne
total memory = 65536 KB
avail memory = 55964 KB
using 844 buffers containing 3376 KB of memory
mainbus0 (root)
cpu0 at mainbus0: QED R4600 Orion CPU (0x2010) Rev. 1.0 with built-in FPU Rev. 0.0
cpu0: 16KB/32B 2-way set-associative L1 Instruction cache, 48 TLB entries
cpu0: 16KB/32B 2-way set-associative write-back L1 Data cache
tyneisabr0 at mainbus0
isa0 at tyneisabr0
3COM 3C509B Ethernet card in PnP mode
ne1 at isa0 port 0x300-0x31f irq 10
ne1: NE2000 Ethernet
ne1: Ethernet address 00:80:c8:3a:6c:99
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0 (mux ignored)
wdc0 at isa0 port 0x1f0-0x1f7 irq 14
atapibus0 at wdc0 channel 0: 2 targets
cd0 at atapibus0 drive 1: <FX800S, , R03> cdrom removable
cd0: drive supports PIO mode 3, DMA mode 1
wd0 at wdc0 channel 0 drive 0: <WDC AC22000L>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 1907 MB, 3876 cyl, 16 head, 63 sec, 512 bytes/sect x 3907008 sectors
wd0: drive supports PIO mode 4, DMA mode 2
vga0 at isa0 port 0x3b0-0x3df iomem 0xa0000-0xbffff
wsdisplay0 at vga0 (kbdmux ignored)
lpt0 at isa0 port 0x378-0x37b irq 7
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
timer0 at isa0 port 0x40-0x43
mcclock0 at isa0 port 0x70-0x71: mc146818 or compatible
isapnp0: read port 0x203
ep0 at isapnp0 port 0x210/16 irq 5
ep0: 3Com 3C509B EtherLink III 
ep0: address 00:a0:24:07:17:7a, 8KB byte-wide FIFO, 5:3 Rx:Tx split
ep0: 10baseT, 10base5 (default 10baseT)
boot device: <unknown>
root device: ne1
dump device: 
file system (default generic): 
root on ne1
mountroot: trying nfs...
nfs_boot: trying DHCP/BOOTP
nfs_boot: DHCP next-server: 192.168.20.8
nfs_boot: my_domain=ceres.dti.ne.jp
nfs_boot: my_addr=192.168.20.16
nfs_boot: my_mask=255.255.255.0
nfs_boot: gateway=192.168.20.8
root on diamante:/export/NetBSD/arc/root
root time: 0x3eeba136
readclock: 23/06/14/22/38/74WARNING: preposterous clock chip time
setclock: 23/06/14/22/27/02
 -- CHECK AND RESET THE DATE!
root file system type: nfs
init path (default /sbin/init): 
init: copying out flags `-s' 3
init: copying out path `/sbin/init' 11
Enter pathname of shell or RETURN for /bin/sh: 
Terminal type is vt220.
We recommend creating a non-root account and using su(1) for root access.
#