Re: Raspberry Pi Zero W almost useless

El 8/2/24 a las 16:48, Nat Sloss escribió:
> Hi,
> 
> There's a little more required to add support for the FTV variant judging by
> changes made to openbsd's if_urtwn.c.
> 
> There's new firware that needs to be uploaded to the device.  And new power on
> and rssi functions (It seems judging by the changes they've made it some what
> is similar to the 8188EUS).
> 
> I'm going to see if I can get one of these adaptors on ebay.
> 
> I't will be awhile though before I try to get it working.
> 
> This is best done on the new wifi stack, so I doubt it will get backported to
> -10.
> 
> In the meantime if you search for an 8192eu variant that will work with -10
> and -9.
> 
> Best regards,
> 
> Nat

Hello Nat,

Thanks for your great explanation, I understand. I then abandon the 
tests with the 8188FTV and wait for your improvements. They will be 
appreciated. I cannot fix anything, the driver world seems to be a hell! :-)

I have just received today from Amazon a TL-WN725N USB WIFI adaptor and 
it just work in the raspberry Pi Zero W:

[     1.710793] urtwn0 at uhub0 port 1
[     1.710793] urtwn0: Realtek (0x0bda) 802.11n NIC (0x8179), rev 
2.00/0.00, addr 2
[     1.770890] urtwn0: MAC/BB RTL8188EU, RF 6052 1T1R, address 
e4:fa:c4:52:ac:4c
[     1.770890] urtwn0: 1 rx pipe, 2 tx pipes



netbsd-raspa# ifconfig
urtwn0: flags=0x8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
	ssid MiFibra-3422 nwkey 65536:"",0xc81111000336c6e2b40b047cd2f5ef44,"",""
	powersave off
	bssid 60:8d:26:32:34:24 chan 1
	address: e4:fa:c4:52:ac:4c
	media: IEEE802.11 autoselect (OFDM54 mode 11g)
	status: active
	inet6 fe80::e6fa:c4ff:fe52:ac4c%urtwn0/64 flags 0 scopeid 0x1
	inet 192.168.1.230/24 broadcast 192.168.1.255 flags 0
lo0: flags=0x8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33176
	status: active
	inet6 ::1/128 flags 0x20<NODAD>
	inet6 fe80::1%lo0/64 flags 0 scopeid 0x2
	inet 127.0.0.1/8 flags 0
bwfm0: flags=0x8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
	ssid "" nwkey 65536:"","","",""
	powersave off
	address: b8:27:eb:ed:85:47
	media: IEEE802.11 autoselect
	status: no network
netbsd-raspa#

I have also the same problem that I had with the chineese 8188FTV,  as 
soon I connect it to the raspberry pi it reboots inmediately. In the 
next reboot it works fine. It occurs the same in another Zero W that I 
own  with Raspbian and a different power supply. So I doubt that the 
culprit is the power supply. The Zero W seems to be a very flaky device 
in terms of power supply.

I am going to test it during several days to see if it works better than 
the flaky bwfm driver for the built in WIFI.

I do not know if I have to  disable the bwfm driver to avoid any 
interaction or I can leave it as is.

Thanks so much.
Ramiro.