Re: booting Zynq 7000 ...

On Thu, Mar 14, 2024 at 01:54:10PM +1300, Lloyd Parkes wrote:
> Kia ora,
> I managed to get NetBSD 10.0_RC5 (the version I happened to have already
> built) booted on a Digilent Zybo. I did this by making a Frankenstein image
> and then using some advice from Brook Milligan about booting a BeagleBone
> Black.
> 
> I took an SD card with a NetBSD arm7.img.gz written to it and then I copied
> over boot.bin and u-boot.img from a FreeBSD image I had found into the
> MS-DOS partition.
> 
> At this point booting the SD card leaves me at the u-boot prompt because I
> haven't configured a uEnv.txt boot script. This suits me fine.
> 
> I can boot NetBSD with the following commands
> 
> 	setenv bootargs "root=ld0a"
> 	fatload mmc 0:1 ${kernel_addr_r} netbsd-GENERIC.ub
> 	fatload mmc 0:1 ${fdt_addr_r} dtb/zynq-zybo.dtb
> 	bootm $kernel_addr_r - $fdt_addr_r

Thanks, Lloyd!  I think this is getting me closer.  I had tried to EFI
boot but that does not seem to be how this board is ordinarily booted.

What do you see on the console after you type `bootm`?  Here is the
typescript of my attempt:

| U-Boot 2016.07 (Apr 28 2022 - 08:48:05 +0000), Build:
| jenkins-redpitaya-master-122-16-15
| 
| Model: Red Pitaya Board
| Board: Xilinx Zynq
| I2C:   ready
| DRAM:  ECC disabled 480 MiB
| I2C:EEPROM selection failed
| MMC:   sdhci@e0100000: 0
| In:    serial@e0000000
| Out:   serial@e0000000
| Err:   serial@e0000000
| Model: Red Pitaya Board
| Board: Xilinx Zynq
| Net:   ZYNQ GEM: e000b000, phyaddr 1, interface rgmii-id
| eth0: ethernet@e000b000
| Hit any key to stop autoboot:  0 
| Running script from SD...
| Device: sdhci@e0100000
| Manufacturer ID: 3
| OEM: 5344
| Name: SC32G 
| Tran Speed: 50000000
| Rd Block Len: 512
| SD version 3.0
| High Capacity: Yes
| Capacity: 29.7 GiB
| Bus Width: 4-bit
| Erase Group Size: 512 Bytes
| reading u-boot.scr
| ** Unable to read file u-boot.scr **
| Zynq> fatload mmc 0 0x04000000 device~1.dtb
| reading device~1.dtb
| 18061 bytes read in 20 ms (881.8 KiB/s)
| Zynq> fatload mmc 0 0x02004000 netbsd.ub
| reading netbsd.ub
| 11854044 bytes read in 700 ms (16.1 MiB/s)
| Zynq> bootm 0x02004000 - 0x04000000      
| ## Booting kernel from Legacy Image at 02004000 ...
|    Image Name:   NetBSD/earmv7hf 10.99.10
|    Image Type:   ARM Linux Kernel Image (no loading done) (uncompressed)
|    Data Size:    11853980 Bytes = 11.3 MiB
|    Load Address: 00000000
|    Entry Point:  00000000
|    Verifying Checksum ... OK
| ## Flattened Device Tree blob at 04000000
|    Booting using the fdt blob at 0x4000000
|    XIP Kernel Image (no loading done) ... OK
|    Loading Device Tree to 1cb3e000, end 1cb4568c ... OK
| 
| Starting kernel ...

It hangs there.

> That DTB file (dtb/zynq-zybo.dtb) is one that NetBSD builds and puts into
> the image. The DTB file that came with the FreeBSD image didn't work for me
> (with NetBSD).

Ok.  Right now I use the .dtb that comes from Red Pitaya.

I wonder what it is that NetBSD needs in the .dtb that the FreeBSD .dtb
does not have....

David

-- 
David Young
[email protected]    Urbana, IL    (217) 721-9981