Re: Can't boot NetBSD from SDcard via UEFI on Raspber ry Pi 5 (8GB D0) - sdmmc1: couldn’t enable card: 60

On 02/01/2026 14:00, Tim McIntosh wrote:
> Hello,
> 
> I recently purchased a Raspberry Pi 5 (8GB, D0 stepping) and have been trying to boot NetBSD on it via UEFI (following the instructions on the wiki <https://wiki.netbsd.org/ports/evbarm/raspberry_pi/>), but have had no luck.
> 
> I believe I’ve tried all of the following:
> 
> https://nycdn.netbsd.org/pub/NetBSD-daily/netbsd-10/latest/evbarm-aarch64/binary/gzimg/arm64.img.gz
> https://nycdn.netbsd.org/pub/NetBSD-daily/netbsd-11/latest/evbarm-aarch64/binary/gzimg/arm64.img.gz
> https://nycdn.netbsd.org/pub/arm/HEAD/20260101113528Z/NetBSD-HEAD-aarch64-20260101113528Z-generic.img.gz
> 
> I’ve also tried fiddling with the UEFI settings, with no improvement.
> 
> In all cases, boot fails after these errors:
> 
> [4.3283271] sdmmc1: couldn’t send I/O OCR
> [4.3383275] sdmmc1: couldn’t enable card: 60
> [7.4883652] sdmmc1: couldn’t send I/O OCR
> [7.4983656] sdmmc1: couldn't enable card: 60
> [10.3984004] sdmmc0: couldn't enable card: 60
> 
> Is this a known issue?

yes, it is. USB or NVME (via hat) storage is best for root anway.

> 
> I saw some previous discussion concerning a similar error recently <https://mail-index.netbsd.org/port-arm/2025/09/18/msg009409.html>, but I’m not sure if that’s related, as that fix would appear to be in at least the HEAD build that I tested.
> 
> The SD card is a new SanDisk Extreme PLUS microSDHC UHS-I 32GB <https://shop.sandisk.com/products/memory-cards/microsd-cards/sandisk-extreme-uhs-i-microsd?sku=SDSQXAF-032G-GN6MA>. I used the Raspberry Pi Imager app on macOS to write the NetBSD image, mounted the boot partition with diskutil, and then copied over the firmware from <https://github.com/NumberOneGit/rpi5-uefi/releases/download/v0.1/RPI5_D0.zip> to the boot partition as instructed before unmounting and attempting to boot from the card.
> 
> Thank you,
> 
> Tim McIntosh
> 
> 
> HDMI console output follows (recovered from photo via OCR):
> 
> 3.3V, re-tuning mode 1(16s timer), 2048 byte blocks
> [1.0000040] sdmmc1 at sdhc1 slot 0
> [1.0000040] genfb0 at simplebus1: Simple Framebuffer (1920x1080 32-bpp @ 0x3f400000)
> [1.0000040] genfb0: framebuffer at 0x3f400000, size 1920x1080, depth 32, stride 7680
> [1.0000040] wsdisplay0 at genfb0 kbdmux 1: console (default, vt100 emulation)
> [1.1674422] uhub0 at usb0: NetBSD (0x0000) xHCI root hub (0x0000), class 9/0, rev 3.00/1.00, addr 0
> [1.1674422] uhub1 at usb1: NetBSD (0x0000) xHCI root hub (0x0000), class 9/0, rev 2.00/1.00, addr 0
> [1.1674422] uhub2 at usb2: NetBSD (0x0000) xHCI root hub (0x0000), class 9/0, rev 3.00/1.00, addr 0
> [1.1674422] uhub3 at usb3: NetBSD (0x0000) xHCI root hub (0x0000), class 9/0, rev 2.00/1.00, addr 0
> [1.1974442] cpu0: PMU interrupting on irq 48
> [1.1974442] cpu1: PWU interrupting on irq 49
> [1.1974442] cpu2: PMU interrupting on irq 50
> [1.1974442] сpuз: PMU interrupting on irq 51
> [1.7082955] uhidev0 at uhub1 port 2 configuration 1 interface 0
> ...
> [1.7182957] ums0 at uhidev0: 3 buttons and Z dir
> [1.7182957] wsmouse0 at ums0 mux 0
> [2.5283055] uhidev1 at uhub4 port 1 configuration 1 interface 0
> [2.5283055] uhidev1: Sony Computer Entertainment Inc. (0x054c) SCE USB Keyboard (0x005c), rev 1.10/0.01, addr 2, class 3/1
> [2.5483057] ukbd0 at uhidev1
> [2.6683072] wskbd0 at ukbd0: console keyboard, using wsdisplay0
> [4.3283271] sdmmc1: couldn’t send I/O OCR
> [4.3383275] sdmmc1: couldn’t enable card: 60
> [7.4883652] sdmmc1: couldn’t send I/O OCR
> [7.4983656] sdmmc1: couldn't enable card: 60
> [10.3984004] sdmmc0: couldn't enable card: 60
> [10.4184017] swwdog0: softuare watchdog initialized
> [10.4184017] WARNING: 5 errors while detecting hardware: check system log.
> [10.4184017] boot device: <unknoun>
> [10.4184017] root device:
> 
>