Re: Problems with my Qube 2

RAM is installed! fingers crossed! :D


Cobalt Microserver Diagnostics - 'We serve it, you surf it'
Built Tue May 25 15:58:41 PDT 1999

  1.LCD Test................................PASS
  2.Controller Test.........................PASS
  5.Bank 0:.................................64M
  6.Bank 1:.................................64M
  7.Bank 2:.................................64M
  8.Bank 3:.................................64M
  9.Serial Test.............................PASS
10.PCI Expansion Slot....................**Unknown Card**
12.IDE Test................................PASS
13.Ethernet Test...........................PASS
16.RTC Test................................PASS
BOOTLOADER ramcode: selected partition /dev/hda1
Decompressing done
Executing bootloader kernel...
Decompressing -- done.

 >> NetBSD/cobalt 5.0.1 Bootloader, Revision 0.9 [@0x80f00000]
 >> ([email protected], Wed Jul 29 19:03:37 UTC 2009)
 >> Model:               Cobalt Qube 2
 >> Memory:              262144 k
 >> PROM boot string:    root=/dev/hda1 ro
Boot [wd0a:netbsd]:
Loading: wd0a:netbsd
3769536+312180 [217328+210281]=0x44d39c
Starting at 0x80001000

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
     2006, 2007, 2008, 2009
     The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
     The Regents of the University of California.  All rights reserved.

NetBSD 5.0.1 (GENERIC) #0: Wed Jul 29 19:14:34 UTC 2009
 
[email protected]:/home/builds/ab/netbsd-5-0-1-RELEASE/cobalt/200907292356Z-obj/home/builds/ab/netbsd-5-0-1
-RELEASE/src/sys/arch/cobalt/compile/GENERIC
Cobalt Qube 2
total memory = 256 MB
avail memory = 245 MB
mainbus0 (root)
com0 at mainbus0 addr 0x1c800000 level 3: st16650a, working fifo
com0: console
cpu0 at mainbus0: QED RM5200 CPU (0x28a0) Rev. 10.0 with built-in FPU 
Rev. 10.0
cpu0: 32KB/32B 2-way set-associative L1 Instruction cache, 48 TLB entries
cpu0: 32KB/32B 2-way set-associative write-back L1 Data cache
mcclock0 at mainbus0 addr 0x10000070: mc146818 compatible time-of-day clock
panel0 at mainbus0 addr 0x1f000000
gt0 at mainbus0 addr 0x14000000
pci0 at gt0
pchb0 at pci0 dev 0 function 0: Galileo GT-64111 System Controller, rev 1
tlp0 at pci0 dev 7 function 0: DECchip 21143 Ethernet, pass 4.1
tlp0: interrupting at level 1
tlp0: Ethernet address 00:10:e0:
lxtphy0 at tlp0 phy 1: LXT970 10/100 media interface, rev. 3
lxtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib0 at pci0 dev 9 function 0
pcib0: VIA Technologies VT82C586 PCI-ISA Bridge, rev 39
viaide0 at pci0 dev 9 function 1
viaide0: VIA Technologies VT82C586 (Apollo VP) ATA33 controller
viaide0: primary channel interrupting at irq 14
atabus0 at viaide0 channel 0
viaide0: secondary channel interrupting at irq 15
atabus1 at viaide0 channel 1
VIA Technologies VT83C572 USB Controller (USB serial bus, revision 0x02) 
at pci0 dev 9 function 2 not configured
Acer Labs M5237 USB 1.1 Host Controller (USB serial bus, interface 0x10, 
revision 0x03) at pci0 dev 10 function 0 not
configured
Acer Labs M5237 USB 1.1 Host Controller (USB serial bus, interface 0x10, 
revision 0x03) at pci0 dev 10 function 1 not
configured
Acer Labs M5237 USB 1.1 Host Controller (USB serial bus, interface 0x10, 
revision 0x03) at pci0 dev 10 function 2 not
configured
Acer Labs M5239 USB 2.0 Host Controller (USB serial bus, interface 0x20, 
revision 0x01) at pci0 dev 10 function 3 not
configured
Acer Labs product 0x5253 (Firewire serial bus, interface 0x10) at pci0 
dev 10 function 4 not configured
tlp1 at pci0 dev 12 function 0: DECchip 21143 Ethernet, pass 4.1
tlp1: interrupting at level 2
tlp1: Ethernet address 00:10:e0:
lxtphy1 at tlp1 phy 1: LXT970 10/100 media interface, rev. 3
lxtphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
wd0 at atabus0 drive 0: <HDS728080PLAT20>
wd0: 78532 MB, 159557 cyl, 16 head, 63 sec, 512 bytes/sect x 160834367 
sectors
Kernelized RAIDframe activated
boot device: wd0
root on wd0a dumps on wd0b