Re: MI com(4) support patch (Re: hp300 switched to MI SCSI)

On Nov 3, 2003, at 2:20 AM, Izumi Tsutsui wrote:

> Could you try serial console? It's very difficult to debug kernel
> without working console anyway.

Seems to work fine on my 362 with serial console.  Alas, there's no 
support for the built-in framebuffer on the 362 and 382, and I need the 
single DIO-I slot for ethernet.  Unless someone out there has a spare 
add-on board for external ethernet/SCSI/HPIB?

Thanks,
   -- MW

NetBSD 1.6ZE (GENERIC) #3: Mon Nov  3 18:39:27 JST 2003
         tsutsui@mirage:/usr/src/sys/arch/hp300/compile/GENERIC
HP 9000/360 (25MHz MC68030 CPU+MMU, 25MHz MC68882 FPU)
cpu: delay divisor 81
total memory = 16372 KB
avail memory = 10976 KB
using 230 buffers containing 920 KB of memory
mainbus0 (root)
intio0 at mainbus0
rtc0 at intio0 addr 0x420000
hil0 at intio0 addr 0x428000 ipl 1
nhpib1 at intio0 addr 0x478000 ipl 3: internal HP-IB
hpibbus1 at nhpib1
dma0 at intio0 addr 0x500000 ipl 1: 98620C, 2 channels, 32-bit DMA
fb at intio0 not configured
dio0 at mainbus0
com0 at dio0 scode 9 ipl 5: ns16550a, working fifo
com0: console
internal parallel at dio0 scode 12 ipl 3 not configured
spc0 at dio0 scode 14 ipl 4: 98265A SCSI, 32-bit DMA, SCSI ID 7
scsibus0 at spc0: 8 targets, 8 luns per target
le0 at dio0 scode 21 ipl 5: address 08:00:09:10:d8:c2
le0: 8 receive buffers, 2 transmit buffers
WARNING: select code size unknown for id = 0x39 secid = 0x11
device id = 0x39 secid = 0x11 at dio0 scode 132 ipl 3 not configured
WARNING: select code size unknown for id = 0x39 secid = 0x11
device id = 0x39 secid = 0x11 at dio0 scode 133 ipl 3 not configured
WARNING: select code size unknown for id = 0x1 secid = 0x0
device id = 0x1 secid = 0x0 at dio0 scode 134 ipl 3 not configured
WARNING: select code size unknown for id = 0x1 secid = 0x0
device id = 0x1 secid = 0x0 at dio0 scode 135 ipl 3 not configured
interrupt levels: bio = 4, net = 5, tty = 5
Kernelized RAIDframe activated
scsibus0: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 0 lun 0: <TEAC, FC-1     HF   07, RV A> disk 
removable
sd0(spc0:0:0:0): not ready, data = 00 00 00 00 04 00 00 00
sd0: drive offline
sd0: async, 8-bit transfers
sd1 at scsibus0 target 2 lun 0: <SEAGATE, ST31230N, 0300> disk fixed
sd1: 1010 MB, 3992 cyl, 5 head, 103 sec, 512 bytes/sect x 2069860 
sectors
sd1: async, 8-bit transfers
sd0(spc0:0:0:0): not ready, data = 00 00 00 00 04 00 00 00
sd0(spc0:0:0:0): illegal request, data = 00 00 00 00 20 00 00 00