Re: 5.0 on hp382

Hi,

huh dmesg pr0n? I'm in :-)
My system is a 400t with a 030. Not heavly tested but seems to work OK, 
like 3.X which was installed before.

Boot: [[[sd3a:]netbsd][-a][-c][-d][-s][-v][-q]] :-
1113340+29108+201248 [253792+130156]=0x1a7fcc
Start @ 0xfc803400 [1=0xfc94c0d4-0x1a7fcc]...
Entry point: 0xfc803400
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.

NetBSD 5.0 (INSTALL) #0: Sun Apr 26 16:27:44 UTC 2009
[email protected]:/home/builds/ab/netbsd-5-0-RELEASE/hp300/200904260229Z-obj/home/builds/ab/netbsd-5-0-RELEASE/srL
HP 9000/400 (50MHz MC68030 CPU+MMU, 50MHz MC68882 FPU, 32K 
physical-address cache)
total memory = 57332 KB
avail memory = 53664 KB
mainbus0 (root)
intio0 at mainbus0
rtc0 at intio0 addr 0x420000
frodo0 at intio0 addr 0x41c000 ipl 5
dnkbd at frodo0 offset 0x0 not configured
com0 at frodo0 offset 0x40: ns8250 or ns16450, no fifo
com1 at frodo0 offset 0x60: ns8250 or ns16450, no fifo
hil0 at intio0 addr 0x428000 ipl 1
dma0 at intio0 addr 0x500000 ipl 1: 98620C, 2 channels, 32-bit DMA
dio0 at mainbus0
com2 at dio0 scode 9 ipl 5: ns16550a, working fifo
com2: console
device id = 0x6 secid = 0x0 at dio0 scode 12 ipl 3 not configured
spc0 at dio0 scode 14 ipl 4: 98265A SCSI, 32-bit DMA, SCSI ID 7
scsibus0 at spc0: 8 targets, 8 luns per target
le0 at dio0 scode 21 ipl 5: address XX:XX:XX:XX:XX:XX
le0: 8 receive buffers, 2 transmit buffers
topcat0 at dio0 scode 132 ipl 3: 1280 x 1024 256 color hi-res catseye 
display
grf0 at topcat0
ite0 at grf0
scsibus0: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 3 lun 0: <SEAGATE, ST32171N, HPM2> disk fixed
sd0: 2033 MB, 5172 cyl, 5 head, 161 sec, 512 bytes/sect x 4165272 sectors
sd0: async, 8-bit transfers
cd0 at scsibus0 target 4 lun 0: <TEAC, CD-ROM CD-532S, 1.0A> cdrom removable
cd0: async, 8-bit transfers
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs
Sun Apr 26 18:03:54 GMT 2009
swapctl: adding /dev/sd0b as swap device at priority 0
Starting file system checks:
/dev/rsd0a: file system is clean; not checking
/dev/rsd0e: file system is clean; not checking
Setting tty flags.

Best Regards
Stephan