Re: Console on 9000/425t with A1659A graphics

On Nov 30, 2018, at 3:33 PM, Izumi Tsutsui <[email protected]> wrote:
> 
> Could you post full dmesg on the serial console?

Below is a dmesg now that I’ve reinstalled the system reasonably. The only difference between the below and a dmesg from a default configuration of NetBSD on this system is the very last line, which was the result of adding to  /etc/rc.conf an entry that said wscons=YES.

  -- Chris

bootinfo found at 0xf8002000
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017,
    2018 The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 8.0 (GENERIC) #0: Tue Jul 17 14:59:51 UTC 2018
        [email protected]:/usr/src/sys/arch/hp300/compile/GENERIC
HP 9000/425t (25MHz MC68040 CPU+MMU+FPU, 4k on-chip physical I/D caches)
total memory = 127 MB
avail memory = 120 MB
timecounter: Timecounters tick every 10.000 msec
Kernelized RAIDframe activated
mainbus0 (root)
intio0 at mainbus0
rtc0 at intio0 addr 0x420000
frodo0 at intio0 addr 0x41c000 ipl 5
dnkbd0 at frodo0 offset 0x0: no keyboard
com1 at frodo0 offset 0x40: ns8250 or ns16450, no fifo
com2 at frodo0 offset 0x60: ns8250 or ns16450, no fifo
hil0 at intio0 addr 0x428000 ipl 1
dma0 at intio0 addr 0x500000 ipl 1: 98620C, 2 channels, 32-bit DMA
dio0 at mainbus0
com0 at dio0 scode 9 ipl 5: ns16550a, working fifo
com0: console
internal parallel at dio0 scode 12 ipl 3 not configured
spc0 at dio0 scode 14 ipl 4: 98265A SCSI, 32-bit DMA, SCSI ID 7
scsibus0 at spc0: 8 targets, 8 luns per target
le0 at dio0 scode 21 ipl 5: address 08:00:09:20:58:93
le0: 8 receive buffers, 2 transmit buffers
sgc0 at mainbus0
sti0 at sgc0 slot 3: rev 8.02;10, ID 0x26D1482A40A00499
sti0: HPA1659A, 2048x1024 frame buffer, 1280x1024x8 display
sti0: 10x20 font type 1, 40 bpc, charset 0-255
wsdisplay0 at sti0 kbdmux 1
wsmux1: connecting to wsdisplay0
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "mc6840" frequency 250000 Hz quality 100
scsibus0: waiting 2 seconds for devices to settle...
hilkbd0 at hil0 code 1: 109-key keyboard, layout 1f
wskbd0 at hilkbd0 mux 1
wskbd0: connecting to wsdisplay0
hilms0 at hil0 code 2: Mouse, 2 axes, 3 buttons
wsmouse0 at hilms0 mux 0
sd0 at scsibus0 target 1 lun 0: <QUANTUM, FIREBALL_TM2110S, 300X> disk fixed
sd0: 2014 MB, 6810 cyl, 4 head, 151 sec, 512 bytes/sect x 4124736 sectors
sd0: async, 8-bit transfers
cd0 at scsibus0 target 5 lun 0: <MATSHITA, CD-ROM CR-8012, 1.0g> cdrom removable
cd0: async, 8-bit transfers
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs
kern.module.path=/stand/hp300/8.0/modules
wsdisplay0: screen 1 added (std, vt100 emulation)