Re: MPC5200 support

On Sat, 18 Jul 2009 18:42:50 +0100 (BST)
Robert Swindells <[email protected]> wrote:

> I have put another snapshot of my MPC5200 code onto ftp.netbsd.org.
> 
> Path is ftp.netbsd.org:/pub/NetBSD/misc/rjs/efika-20090718.tar.gz

I compiled your latest patches and the kernel boots:

Loaded initial symtab at 0x3af750, strtab at 0x3d7ec4, # entries 10262
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.99.11 (EFIKA) #6: Sun Jul 19 22:41:13 CEST 2009
	[email protected]:/home/frank/netbsd_test/src/sys/arch/ofppc/compile/obj/EFIKA
Model: EFIKA5K2
total memory = 128 MB
avail memory = 99 MB
bootpath: 
mainbus0 (root)
rtas0 at mainbus0: version 1, entry @pa 0x1cc5000
cpu0 at mainbus0: G2 (Revision 1.4), ID 0 (primary)
cpu0: HID0 0x90c000<DOZE,DPM,ICE,DCE>, powersave: 1
cpu0: L1 I-cache 16 KB 32B/line, D-cache 16 KB 32B/line
ofwpci0 at mainbus0
Found MPC5200 PIC at f0000500
pci_configure_bus() failed
pci0 at ofwpci0 bus 0: OFW method configuration space access
vendor 0x1002 product 0x5960 (VGA display, revision 0x01) at pci0 dev 16 function 0 not configured
vendor 0x1002 product 0x5940 (miscellaneous display, revision 0x01) at pci0 dev 16 function 1 not configured
bestcomm0 at mainbus0
sram0 at mainbus0
mpcide0 at mainbus0
mapping irq 71 to virq 1
mpc5200_establish_irq: irq 71 type 3 pri 5
mpcide0: PIO1 562a1800 PIO2 050a0500 DMA1 00000000 DMA2 00000000
mpcide0: UDMA1 00000000 UDMA2 00000000 UDMA3 00000000 UDMA4 00000000 UDMA5 00000000
atabus0 at mpcide0 channel 0
ohci_match name: mpc5200-ohci
ohci0 at mainbus0
mapping irq 70 to virq 2
mpc5200_establish_irq: irq 70 type 2 pri 5
ohci0: OHCI version 1.0
usb0 at ohci0: USB revision 1.0
psc0 at mainbus0
psc0: console 0x0 0xa0069d00 0
psc0: psc_config MR1 73 MR2 7
mapping irq 65 to virq 3
mpc5200_establish_irq: irq 65 type 2 pri 7
cdm0 at mainbus0
cdm0: Config 01000001
cdm0: Fractional Divider 1bbbb
cdm0: Clock Enable ffffff
biomask 8000006 netmask 8000006 ttymask 8000006
wd0 at atabus0 drive 0: <TS64GSSD25-M>
wd0: 61136 MB, 124212 cyl, 16 head, 63 sec, 512 bytes/sect x 125206528 sectors
uhub0 at usb0: mpc5200-ohci OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1 at uhub0 port 1: vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/9.01, addr 2
boot device: rtas0
can't determine root device
root device (default rtas0):


When booting with USB keyboard connected, then it is detected by the
kernel but doesn't work. Do you know why?


> It still doesn't have any Bestcomm support so can't use the built in
> ethernet controller but I'm running it multi-user using a rtk(4) PCI
> ethernet card.

That's great! I have to look for a network card to try it.


-- 
    _  Frank Wille ([email protected])
 _ //  http://sun.hasenbraten.de/~frank/
 \X/   Phx @ #AmigaGer