Re: Trouble booting an IBM 7248 after installation

On 29 June 2014 06:45, William Orr <[email protected]> wrote:
> Hello all,
>
> I=E2=80=99ve *almost* successfully installed NetBSD on my IBM 7248. My sy=
stem is a little special though - the SCSI drive that it had was bad, so I =
instead installed on a CF Card that=E2=80=99s plugged into the IDE controll=
er. The installation of NetBSD went beautifully, however I can=E2=80=99t bo=
ot my system.
>
> The SMS sees the CF card as a bootable device, and when booting to it, th=
e serial console hangs and the system never comes up. There=E2=80=99s no re=
al activity happening on the CF card.
>
> I then tried creating a netbootable image with the hope of netbooting int=
o my installed system. I booted up the installer again, and dropped to a sh=
ell. I chrooted into my system and did /usr/mdec/mkbootimage -m prep -b /us=
r/mdec/boot_com0 -k /netbsd boot.fs and tried netbooting again. The system =
grabbed it via tftp, but it hung afterwards. Again, there were no reads on =
the CF card.
>
> It=E2=80=99s worth noting that the CF card is 8GB, and SMS only sees it a=
s roughly 3.7 GBs.
>
> Here=E2=80=99s the partition table:
>
> # fdisk /dev/wd0
> Disk: /dev/wd0c
> NetBSD disklabel disk geometry:
> cylinders: 15538, heads: 16, sectors/track: 63 (1008 sectors/cylinder)
> total sectors: 15662304
>
> BIOS disk geometry:
> cylinders: 975, heads: 255, sectors/track: 63 (16065 sectors/cylinder)
> total sectors: 15662304
>
> Partitions aligned to 16065 sector boundaries, offset 63
>
> Partition table:
> 0: Linux/MINIX (sharing disk with DRDOS) or Personal RISC boot (sysid 65)
>     start 63, size 9800 (5 MB, Cyls 0-0/156/35), Active
>         PBR is not bootable: All bytes are identical (0x00)
> 1: NetBSD (sysid 169)
>     start 9863, size 15652441 (7643 MB, Cyls 0/156/36-974/237/63)
>         PBR is not bootable: All bytes are identical (0x00)
> 2: <UNUSED>
> 3: <UNUSED>
> First active partition: 0
>
>
> And the disklabel:
>
> # /dev/wd0c:
> type: unknown
> disk: TS8GCF133
> label:
> flags:
> bytes/sector: 512
> sectors/track: 63
> tracks/cylinder: 16
> sectors/cylinder: 1008
> cylinders: 15538
> total sectors: 15662304
> rpm: 3600
> interleave: 1
> trackskew: 0
> cylinderskew: 0
> headswitch: 0           # microseconds
> track-to-track seek: 0  # microseconds
> drivedata: 0
>
> 8 partitions:
> #        size    offset     fstype [fsize bsize cpg/sgs]
>  a:  15127056      9863     4.2BSD   2048 16384     0  # (Cyl.      9*-  =
15016*)
>  b:    263088  15136919       swap                     # (Cyl.  15016*-  =
15277*)
>  c:  15662304         0     unused      0     0        # (Cyl.      0 -  =
15537)
>  e:      9800        63       boot                     # (Cyl.      0*-  =
    9*)
>
> Any help would be very much appreciated.

Its possible the 7248 is not happy with the CF to IDE adaptor, but
they are generally pretty compatible. Are you booting from SCSI CD and
running sysinst to install onto CF-on-IDE ?

I can't recall NetBSD's prep boot loader offhand - does it give a few
seconds countdown and an option to hit space to abort? If so could you
try interrupting the CD boot and then running 'boot netbsd -a'? If it
works it should prompt for a root device, which is probably going to
be wd0a to run from the installed system. If that works then it means
one workaround (for right now) would be to build a bootable CD with a
kernel set to use root on wd0a.