Re: SCSI changes for Indy machines?

Hi John,

In 4.x and beyond we have an MI version of the wdsc driver. Ben Harris  
took the sgimips code and modified it appropriately. It always worked  
fine for me, however.

Would it be possible to try a -current kernel? There have been some  
changes since, though none I can recall which I would immediately  
expect to fix your issue.

Steve

On Aug 23, 2008, at 3:09 PM, John Klos wrote:

> Hi,
>
> It's been a while since I've had my SGI Indy running NetBSD, and I  
> figured I'd get it running NetBSD 4. I loaded a freshly cross- 
> compiled netbsd-4 GENERIC kernel and OS via NetBSD-3 which was  
> already on this machine, but it can't go multiuser with NetBSD-4 (I  
> have two drives - one with NetBSD-3 and one with NetBSD-4):
>
> scsibus0: waiting 2 seconds for devices to settle...
> sd0 at scsibus0 target 1 lun 0: <SEAGATE, ST34371W, 0280> disk fixed
> sd0: 4148 MB, 5168 cyl, 10 head, 164 sec, 512 bytes/sect x 8496960  
> sectors
> sd0: sync (200.00ns offset 12), 8-bit (5.000MB/s) transfers, tagged  
> queueing
> sd1 at scsibus0 target 2 lun 0: <Maxtor 6, B250R0, BAH4> disk fixed
> sd1: 233 GB, 121586 cyl, 64 head, 63 sec, 512 bytes/sect x 490234752  
> sectors
> sd1: sync (200.00ns offset 8), 8-bit (5.000MB/s) transfers, tagged  
> queueing
> probe(wdsc0:0:3:0): wdsc0: timed out; asr=0x20 [acb 0x97dc4f88  
> (flags 0x1, dleft
> 24)], <state 5, nexus 0x97dc4f88, resid 24, msg(q 0,o  
> 0)>probe(wdsc0:0:3:0): AB
> ORT in timeout: csr=0xff, asr=0x20
> probe(wdsc0:0:3:0): sending ABORT command
> probe(wdsc0:0:3:0): Resetting bus
> probe(wdsc0:0:3:0): wdsc0: timed out; asr=0x00 [acb 0x97dc4f88  
> (flags 0x41, dlef
> t 24)], <state 8, nexus 0x97dc4f88, resid 24, msg(q 0,o  
> 0)>probe(wdsc0:0:3:0): A
> BORT in timeout: csr=0x01, asr=0x00
> probe(wdsc0:0:3:0): sending ABORT command
> probe(wdsc0:0:3:0): sending DISCONNECT to target
> wd33c93_wait: TIMEO @904 with asr=x0 csr=x1
> wd33c93_wait: TIMEO @904 with asr=x0 csr=x1
> wd33c93_wait: TIMEO @904 with asr=x0 csr=x1
> wd33c93_wait: TIMEO @904 with asr=x0 csr=x1
> wd33c93_wait: TIMEO @904 with asr=x0 csr=x1
> wd33c93_wait: TIMEO @904 with asr=x0 csr=x1
> wd33c93_wait: TIMEO @904 with asr=x0 csr=x1
> wd33c93_wait: TIMEO @904 with asr=x0 csr=x1
> wd33c93_wait: TIMEO @904 with asr=x0 csr=x1
>
> After doing this for a while, the system reboots itself.
>
> Any ideas about what might've changed that could've caused this? The  
> system is fine and happy with any amount of I/O on either or both  
> disks when booted into NetBSD-3.
>
> The Indy, BTW , is new enough that it boots ELF directly with an  
> R4600.
>
> Thanks,
> John Klos