Re: 5.1 panics on a Challenge S

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Hello,

On Feb 15, 2011, at 6:28 AM, George Harvey wrote:

> I tried to install 5.1 on my Challenge S and the kernel panics just
> after the 'panel0' line, see below for full output. The panic happens
> with both the INSTALL and GENERIC kernels on a Challenge S but both
> kernels boot normally on an Indy. I've built a custom kernel with the
> 'panel' line commented out of the config, that cures the panic and the
> kernel then boots normally.
>
> George
>
> == console capture ==
>
> NetBSD 5.1 (INSTALL32_IP2x) #0: Sat Nov  6 18:17:53 UTC 2010
> 	[email protected]:/hme/builds/ab/netbsd-5-1-RELEASE/sgimips/ 
> 20101101943Z-obj/home/builds/ab/netbsd-5-1-RELEASE/src/sys/arch/ 
> sgimips/cmpile/INSTALL32_IP2x
> total memory = 192 MB
> (768 KB reserved for ARCS)
> avail memory = 180 MB
> mainbus0 (rot): SGI-IP22 [SGI, 690ac9fb], 1 processor
> cpu0 at mainbus0: MIPS R5000 CPU (0x2310) Rev. 1.0 with built-in FPU
> Rev. 1.0 cpu0: 32KB/32B 2-way set-associative L1 Instruction cach, 48
> TLB entries cpu0: 32KB/32B 2-way set-associative write-back 1 Data  
> cache
> cpu0: 512KB/32B direct-mapped wrie-through L2 Data cache
> ioc0 at mainbus0 addr 0x1fbd9800: rev 0, machine Indy (Guinness),  
> board
> rev 0 int0 at mainbus0 addr 0x1fbd9880
> int0: bus 90MHz, CPU 180MHz
> imc0 at mainbus0 addr 0x1fa00000: revision 3
> gio0 at imc0
> giopci0 at gio0 slot 1 addr 0x1f400000: Phobos G130 10/100 Ethernet
> pci0 at giopci0 bus 0
> tlp0 at pci0 dev 0 function 0: DECchip 21143 Ethernet, pass 4.1
> tlp0: sorry, unable to handle your board
> hpc0 at gio0 addr 0x1fb80000: SGI HPC3 (onboard)
> zsc0 at hpc0 offset 0x59830
> zstty0 at zsc0 channel 1 (console i/o)
> zstty1 at zsc0 channel 0
> pckbc0 at hpc0 offset 0x59840
> sq0 at hpc0 offset 0x54000: SGI Seeq 80c03
> sq0: Ethernet address 08:00:69:0a:c9:fb
> wdsc0 at hpc0 offset 0x44000: WD33C93B (20.0 MHz clock, BURST DMA,  
> SCSI
> ID 0) wdsc0: microcode revision 0x0d, Fast SCSI
> scsibus0 at wdsc0: 8 targets, 8 luns per target
> dsclock0 at hpc0 offset 0x60000
> pi1ppc0 at hpc0 offset 0x58000
> pi1ppc0: capabilities=8<PS2>
> ppbus0 at pi1ppc0
> ppbus0: No IEEE1284 device found.
> panel0 at hpc0 offset 0x59800
> panic: invalid interrupt level
> Stopped in pid 0.1 (system) at  0x882dc0e4:     jr      ra
>                bdslot: nop
> db> bt
> 0+882dc0e4 (93ffe000,d,0,880478f4) ra 0 sz 0
> User-level: pid 0.1
> db>

Sounds like the panel driver screwing up - I only had a chance to test  
it on an Indy. Could you try a kernel without it?

have fun
Michael

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.7 (Darwin)

iQEVAwUBTVp+LspnzkX8Yg2nAQLHyQf8CeoWVMtOn5GnCgRA/WXbv/54Qmb7QJsZ
/HJw5+MajPuOGZS6rmjdE/68m4HHtO+wrPGfaWq3bgnnGHc1A+9XSfYhRJOZlH2v
nr0Jecjkv39kkKNyaczFqFAaEXbOf6AHjYnMWbyGnGD3TlAT78/aGe+ZGE6hNZDV
ib+BAzfegKXiWnn4NJD92DTiKTZ8zngFObYnj1Q4drJVvo+PQFdsbvcP6g1HlmA2
0uznGhoTiLOjxmXFYMj/9FoawiQGRK6L9AyJ221mCjAYON5cFIl+NL477L7RKBMX
1wrbbG23b0Lk4veT8uDbeeNeWRUpF3mK+MdqWEhRtT2UJgOwECEMrA==
=GUEl
-----END PGP SIGNATURE-----