Re: Keyboard Problem with V5.1 on an E4000

On Thu, Jul 28, 2011 at 2:16 PM, doomwarrior <[email protected]> wrote:
>
>> > From the kernel messages, can you tell what variant of {e,u,o}hci the
>> > usb
>> is on and what it says about the keyboard?
>>
>> Can you try a current snapshot?
>>
>> Martin
>>
> It is a E4000 - big Iron - this shouldn't have a USB-controller at all!
> Normal Keyboard-connector was still type5 keyboard back then - At least my
> E4500 has one.
> The E4000 and E4500 are very similar so I doubt there is a difference.
>
> Best Regards
>
>
>

It has the normal Sun non-USB keyboard port on an I/O board in slot 0.
It has a CGSix Sbus board on the I/O board in slot 0.

I pulled all of the CPU boards but one to simplify the configuration.

With the keyboard unplugged and using the serial console:

ok boot cdrom
Boot device: /sbus@3,0/SUNW,fas@3,8800000/sd@6,0:f  File and args:
NetBSD IEEE 1275 Bootblock
>> NetBSD/sparc64 OpenFirmware Boot, Revision 1.13
devopen: getdisklabel returned no disk label
=0xd59708
Loading netbsd: 6537784+5609160+442248=0xdc5b90
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.1 (INSTALL) #0: Sat Nov  6 19:23:36 UTC 2010
        [email protected]:/home/builds/ab/netbsd-5-1-RELEASE/sparc64/201011061943Z-obj/home/builds/ab/netbsd-5-1-RELEASE/src/sys/arch/sparc64/compile/INSTALL
total memory = 1024 MB
avail memory = 981 MB
mainbus0 (root): SUNW,Ultra-Enterprise (8-slot Sun Enterprise
E4500/E5500): hostid 809db71e
cpu0 at mainbus0: SUNW,UltraSPARC-II @ 336 MHz, UPA id 0
cpu0: 16K instruction (32 b/l), 16K data (32 b/l), 4096K external (64 b/l)
cpu at mainbus0 not configured
central at mainbus0 not configured
fhc at mainbus0 not configured
sbus0 at mainbus0 addr 0xffdb6000: clock = 25 MHz
DVMA map: ff800000 to ffffe000
IOTSB: 118e000 to 1190000
SUNW,socal at sbus0 slot 13 offset 0x10000 vector 22 ipl 2 not configured
cgsix0 at sbus0 slot 1 offset 0x0 vector 5 ipl 5: SUNW,501-2325, 1152
x 900, rev 11
cgsix0: attached to /dev/fb0
cgsix0: framebuffer size: 1 MB
cgsix0: FBC: 00229540
wsdisplay1 at cgsix0 kbdmux 1
fhc at mainbus0 not configured
timer0 at mainbus0 addr 0xffd99c00 irq vectors b0 and b1
sbus1 at mainbus0 addr 0xffd8e000: clock = 25 MHz
DVMA map: ff800000 to ffffe000
IOTSB: 1190000 to 1192000
hme0 at sbus1 slot 3 offset 0x8c00000 vector 4 ipl 6: Sun Happy Meal
Ethernet (SUNW,hme)
hme0: Ethernet address 08:00:20:9d:b7:1e
nsphy0 at hme0 phy 1: DP83840 10/100 media interface, rev. 1
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
esp0 at sbus1 slot 3 offset 0x8800000 vector 3 ipl 3: FAS366/HME,
40MHz, SCSI ID 7
scsibus0 at esp0: 16 targets, 8 luns per target
SUNW,socal at sbus1 slot 0 offset 0x0 vector 3 ipl 2 not configured
timer1 at mainbus0 addr 0xffd7fc00 irq vectors f0 and f1
pcons0 at mainbus0
scsibus0: waiting 2 seconds for devices to settle...
cd0 at scsibus0 target 6 lun 0: <TOSHIBA, XM5701TASUN12XCD, 0997>
cdrom removable
cd0: sync (100.00ns offset 8), 8-bit (10.000MB/s) transfers
Kernelized RAIDframe activated
root on md0a dumps on md0b
root file system type: ffs
WARNING: no TOD clock present
WARNING: using filesystem time
WARNING: CHECK AND RESET THE DATE!
erase ^?, werase ^W, kill ^U, intr ^C

If you are using a SUN type 4 keyboard, please enter "sun-type4".
Terminal type (just hit ENTER for 'sun'):

With the keyboard installed and after it changes the video configuration:

wsdisplay0 at cgsix0 kbdmux 1: console (std, sun emulation)
fhc at mainbus0 not configured
timer0 at mainbus0 addr 0xffd99c00 irq vectors b0 and b1
sbus1 at mainbus0 addr 0xffd8e000: clock = 25 MHz
DVMA map: ff800000 to ffffe000
IOTSB: 1190000 to 1192000
hme0 at sbus1 slot 3 offset 0x8c00000 vector 4 ipl 6: Sun Happy Meal
Ethernet (SUNW,hme)
hme0: Ethernet address 08:00:20:9d:b7:1e
nsphy0 at hme0 phy 1: DP83840 10/100 media interface, rev. 1
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
esp0 at sbus1 slot 3 offset 0x8800000 vector 3 ipl 3: FAS366/HME,
40MHz, SCSI ID 7
scsibus0 at esp0: 16 targets, 8 luns per target
SUNW,socal at sbus1 slot 0 offset 0x0 vector 3 ipl 2 not configured
timer1 at mainbus0 addr 0xffd7fc00 irq vectors f0 and f1
pcons0 at mainbus0 not configured
scsibus0: waiting 2 seconds for devices to settle...
cd0 at scsibus0 target 6 lun 0: <TOSHIBA, XM5701TASUN12XCD, 0997>
cdrom removable
cd0: sync (100.00ns offset 8), 8-bit (10.000MB/s) transfers
Kernelized RAIDframe activated
root on md0a dumps on md0b
root file system type: ffs
WARNING: no TOD clock present
WARNING: using filesystem time
WARNING: CHECK AND RESET THE DATE!
erase ^?, werase ^W, kill ^U, intr ^C

If you are using a SUN type 4 keyboard, please enter "sun-type4".
Terminal type (just hit ENTER for 'sun'):

At this point the keyboard is unresponsive, even to a Stop-A.

I installed NetBSD V5.1 on a SCSI disk and the system seems to run
fine using the serial port as the console. Time to add some more CPUs

-- 
Michael Thompson