Sun Fire v120, satalink etc.

Hello,

just for the record, that's my new toy:
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2
004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 6.99.23 (BRANCA) #0: Sun Sep  8 10:54:55 EDT 2013
        ml@connemara:/home/build/obj_sparc64/sys/arch/sparc64/compile/BRANCA
total memory = 2048 MB
avail memory = 2000 MB
timecounter: Timecounters tick every 10.000 msec
mainbus0 (root): SUNW,UltraAX-i2 (Sun Fire V120): hostid 8335d0de
cpu0 at mainbus0: SUNW,UltraSPARC-IIe @ 648 MHz, UPA id 0
cpu0: system tick frequency 11 MHz
cpu0: 16K instruction (32 b/l), 16K data (32 b/l), 512K external (64 b/l)
psycho0 at mainbus0
psycho0: SUNW,sabre: impl 0, version 0: ign 7c0 bus range 0 to 2; PCI bus 0
psycho_alloc_extent: no "available" property
psycho_alloc_extent: no "available" property
pci0 at psycho0
pci0: i/o space, memory space enabled
ppb0 at pci0 dev 1 function 1: Sun Microsystems Simba PCI Bridge (rev. 0x13)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
ebus0 at pci1 dev 12 function 0
ebus0: Sun Microsystems PCIO Ebus2 (US III), revision 0x01
flashprom at ebus0 addr 0-fffff not configured
clock0 at ebus0 addr 0-1fff: mk48t59
ebus_attach: idprom: incomplete
lom0 at ebus0 addr 200000-200003 ipl 2a: SUNW,lomh: LOMlite2 rev 3.12
lom0: 4 fan(s), 1 PSU(s), 1 temp sensor(s)
lom0: Watchdog timer configured.
alipm0 at pci1 dev 3 function 0: 74KHz clock
iic0 at alipm0: I2C bus
admtemp0 at iic0 addr 0x18: ADM1021 or compatible environmental sensor
spdmem0 at iic0 addr 0x54
spdmem0: SDRAM (registered), data ECC, 512MB, 133MHz (PC-133)
spdmem0: 13 rows, 11 cols, 1 banks, 4 banks/chip, 7.5ns cycle time
spdmem0: tAA-tRCD-tRP-tRAS: 3-15-15-37
spdmem0: voltage LvTTL (not 5V tolerant), refresh time 7.8us (self-refreshing)
spdmem1 at iic0 addr 0x55
spdmem1: SDRAM (registered), data ECC, 512MB, 133MHz (PC-133)
spdmem1: 13 rows, 11 cols, 1 banks, 4 banks/chip, 7.5ns cycle time
spdmem1: tAA-tRCD-tRP-tRAS: 3-15-15-37
spdmem1: voltage LvTTL (not 5V tolerant), refresh time 7.8us (self-refreshing)
spdmem2 at iic0 addr 0x56
spdmem2: SDRAM (registered), data ECC, 512MB, 133MHz (PC-133)
spdmem2: 13 rows, 11 cols, 1 banks, 4 banks/chip, 7.5ns cycle time
spdmem2: tAA-tRCD-tRP-tRAS: 3-15-15-37
spdmem2: voltage LvTTL (not 5V tolerant), refresh time 7.8us (self-refreshing)
spdmem3 at iic0 addr 0x57
spdmem3: SDRAM (registered), data ECC, 512MB, 133MHz (PC-133)
spdmem3: 13 rows, 11 cols, 1 banks, 4 banks/chip, 7.5ns cycle time
spdmem3: tAA-tRCD-tRP-tRAS: 3-15-15-37
spdmem3: voltage LvTTL (not 5V tolerant), refresh time 7.8us (self-refreshing)
seeprom0 at iic0 addr 0x50: i2c-nvram: size 8192
seeprom1 at iic0 addr 0x51: motherboard-fru: size 8192
ebus1 at pci1 dev 7 function 0
ebus1: Acer Labs M1533 PCI-ISA Bridge, revision 0x00
power at ebus1 addr 800-82f ipl 25 not configured
com0 at ebus1 addr 3f8-3ff ipl 2b: ns16550a, working fifo
com0: console
com1 at ebus1 addr 2e8-2ef ipl 2b: ns16550a, working fifo
gem0 at pci1 dev 12 function 1: Sun Microsystems ERI Ethernet (rev. 0x01)
gem0: interrupting at ivec 3006
ukphy0 at gem0 phy 1: OUI 0x0008bb, model 0x0002, rev. 1
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
gem0: Ethernet address 00:03:ba:35:d0:de, 2KB RX fifo, 2KB TX fifo
ohci0 at pci1 dev 12 function 3: Sun Microsystems USB Controller (rev. 0x01)
ohci0: interrupting at ivec 24
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
aceride0 at pci1 dev 13 function 0: Acer Labs M5229 UDMA IDE Controller (rev. 
0xc3)
aceride0: bus-master DMA support present
aceride0: using PIO transfers above 137GB as workaround for 48bit DMA access 
bug, expect reduced performance
aceride0: primary channel configured to native-PCI mode
aceride0: using ivec 180c for native-PCI interrupt
atabus0 at aceride0 channel 0
aceride0: secondary channel configured to native-PCI mode
atabus1 at aceride0 channel 1
gem1 at pci1 dev 5 function 1: Sun Microsystems ERI Ethernet (rev. 0x01)
gem1: interrupting at ivec 301c
ukphy1 at gem1 phy 1: OUI 0x0008bb, model 0x0002, rev. 1
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
gem1: Ethernet address 00:03:ba:35:d0:de, 2KB RX fifo, 2KB TX fifo
ohci1 at pci1 dev 5 function 3: Sun Microsystems USB Controller (rev. 0x01)
ohci1: interrupting at ivec 26
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
ppb1 at pci0 dev 1 function 0: Sun Microsystems Simba PCI Bridge (rev. 0x13)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
esiop0 at pci2 dev 8 function 0: Symbios Logic 53c896 (ultra2-wide scsi)
esiop0: using on-board RAM
esiop0: interrupting at ivec 1820
scsibus0 at esiop0: 16 targets, 8 luns per target
esiop1 at pci2 dev 8 function 1: Symbios Logic 53c896 (ultra2-wide scsi)
esiop1: using on-board RAM
esiop1: interrupting at ivec 1820
scsibus1 at esiop1: 16 targets, 8 luns per target
satalink0 at pci2 dev 5 function 0: Silicon Image SATALink 3512 (rev. 0x01)
satalink0: SATALink BA5 register space disabled
satalink0: bus-master DMA support present
satalink0: primary channel wired to native-PCI mode
satalink0: using ivec 15 for native-PCI interrupt
atabus2 at satalink0 channel 0
satalink0: secondary channel wired to native-PCI mode
atabus3 at satalink0 channel 1
pcons at mainbus0 not configured
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "tick-counter" frequency 648000000 Hz quality 100
timecounter: Timecounter "stick-counter" frequency 11111111 Hz quality 200
No counter-timer -- using STICK at 11MHz as system clock.
scsibus0: waiting 2 seconds for devices to settle...
scsibus1: waiting 2 seconds for devices to settle...
satalink0: port 0: device present, speed: 1.5Gb/s
wd0 at atabus2 drive 0
uhub0 at usb0: Sun Microsystems OHCI root hub, class 9/0, rev 1.00/1.00, addr 
1
uhub0: 4 ports with 4 removable, self powered
uhub1 at usb1: Sun Microsystems OHCI root hub, class 9/0, rev 1.00/1.00, addr 
1
uhub1: 4 ports with 4 removable, self powered
wd0: <WDC WD5000AVDS-73U7B1>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(satalink0:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
sd0 at scsibus0 target 0 lun 0: <NETAPP, X243_FAL7E073S10, NA00> disk fixed
sd0: 70092 MB, 29902 cyl, 8 head, 600 sec, 512 bytes/sect x 143550456 sectors
sd0: sync (25.00ns offset 31), 16-bit (80.000MB/s) transfers, tagged queueing

wd0 is an external disk hooked to a cheap SiI eSATA card. So, satalink Just 
Works(tm). Anything faster than 1.5GBit/s wouldn't make much sense anyway 
since the PCI slot is 32bit/33MHz and that disk can pretty much saturate it.

have fun
Michael