Re: can't get tcp/ip to work under qemu/SPARC64/NetBSD 6.1.5

thx it works

Am 11.08.2015 um 06:36 schrieb Jason:
> Its been a while since i wrote that guide, and back then the networking and disk emulation had issues..
>
> http://virtuallyfun.superglobalmegacorp.com/category/netbsd/
>
> In the gunkies article i omitted the networking as it was more stable without.
>
> Try adding this:
>
> —net nic,model=e1000 —net user
>
>
>  From Meizu MX4 Pro
>
> -------- Original message --------
> Sender: Dennis Luehring <[email protected]>
> Time: Tue 8/11 AM 01:01
> To: [email protected]
>   Subject: can't get tcp/ip to work under qemu/SPARC64/NetBSD 6.1.5
>
> >i try to build a system for while-develop big-endian/unaligned acces
> >checks, got a working debian-sparc64
> >running - buts its awfully slow due to 32/64-kernel/userland mixup -
> >NetBSD is pure SPARC64 and is blasting
> >fast under qemu - the installation runs very quick (just a few minutes)
> >from CD/with "full without X"
> >but i can't get the network to work - trying to use dhcp during
> >installation fails, manual IP settings fail also
> >i don't know if it is a hardware(emulation) problem or my little to none
> >knowledge of NetBSD
> >
> >Qemu:
> >
> >using git qemu 2.3.93 (latest release 2.2 isn't able to boot NetBSD at all)
> >
> >needed packages under ubuntu (15.04) for building
> >
> >g++
> >git
> >glib2.0-dev
> >libfdt-dev
> >libgtk2.0-dev
> >libncurses5-dev
> >libpixman-1-dev
> >libsdl1.2-dev
> >libvte-dev
> >zlib1g-dev
> >
> >git clone git://git.qemu-project.org/qemu.git
> >cd qemu
> >./configure --target-list=sparc64-softmmu
> >make // no "make install" neeeded
> >
> >Image:
> >
> >using the SPARC64 NetBSD 6.1.5 iso image
> >ftp://iso2.de.netbsd.org/pub/NetBSD/iso/6.1.5/NetBSD-6.1.5-sparc64.iso
> >
> >base on this small howto:
> >http://gunkies.org/wiki/Installing_NetBSD_6.1.5_Sparc64_on_Qemu
> >
> >Create image:
> >~/qemu/qemu-img create -f raw ~/netbsd/netbsd-615-sparc64.raw 2G
> >
> >Start installation (use cd0c if asked)
> >~/qemu/sparc64-softmmu/qemu-system-sparc64 -m 1024 -nographic -monitor
> >telnet::4440,server,nowait -serial telnet::3000,server -hda
> >./netbsd-615-sparc64.raw -cdrom ./NetBSD-6.1.5-sparc64.iso -boot d -net
> >nic -net user
> >
> >Run installed system (use wd0a if asked)
> >~/qemu/sparc64-softmmu/qemu-system-sparc64 -m 1024 -nographic -monitor
> >telnet::4440,server,nowait -serial telnet::3000,server -hda
> >./netbsd-615-sparc64.raw -cdrom ./NetBSD-6.1.5-sparc64.iso -boot c -net
> >nic -net user
> >
> >telnet localhost 3000 - guest
> >telnet localhost 4440 - qemu monitor