Re: Looking for V210/V240 testers

Here is what I got:

v240# uname -a
NetBSD v240.retronet.burn.net 11.99.5 NetBSD 11.99.5 (GENERIC) #0: Wed =
Feb 25 11:57:46 UTC 2026  =
[email protected]:/usr/src/sys/arch/sparc64/compile/GENERIC =
sparc64

v240# dmesg | grep -i adm1026hm0
[     1.000000] adm1026hm0 at iic0 addr 0x2e: ADM1026 hardware monitor: =
rev. 0x4, step. 0x5
[     1.000000] adm1026hm0: 8 fans, 3 temperatures, 15 voltages
[     1.000000] adm1026hm0 at iic0 addr 0x2e: ADM1026 hardware monitor: =
rev. 0x4, step. 0x5
[     1.000000] adm1026hm0: 7 fans, 3 temperatures, 15 voltages

I think that spans two different boots though.  8 fans and then 7 fans ?

Also to be honest - I saw this thread but didn=E2=80=99t follow it.  I =
will go back and try to read the archives to get the gist of this =
current work.

Let me know what else I can look at or test. =20

Full dmesg:

[ [   1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, =
2003,
[     1.000000]     2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, =
2012, 2013,
[     1.000000]     2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, =
2022, 2023,
[     1.000000]     2024, 2025, 2026
[     1.000000]     The NetBSD Foundation, Inc.  All rights reserved.
[     1.000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[     1.000000]     The Regents of the University of California.  All =
rights reserved.

[     1.000000] NetBSD 11.99.5 (GENERIC) #0: Wed Feb 25 11:57:46 UTC =
2026
[     1.000000]         =
[email protected]:/usr/src/sys/arch/sparc64/compile/GENERIC
[     1.000000] total memory =3D 4096 MB
[     1.000000] avail memory =3D 4002 MB
[     1.000000] timecounter: Timecounters tick every 10.000 msec
[     1.000000] Kernelized RAIDframe activated
[     1.000000] mainbus0 (root): SUNW,Sun-Fire-V240 (Sun Fire V240): =
hostid 84911c8e
[     1.000000] cpu0 at mainbus0: SUNW,UltraSPARC-IIIi @ 1503 MHz, CPU =
id 0
[     1.000000] cpu0: manuf 3e, impl 16, mask 34
[     1.000000] cpu0: system tick frequency 12 MHz
[     1.000000] cpu0: 32K instruction (32 b/l), 64K data (32 b/l), 1024K =
external (64 b/l)
[     1.000000] cpu1 at mainbus0: SUNW,UltraSPARC-IIIi @ 1503 MHz, CPU =
id 1
[     1.000000] cpu1: manuf 3e, impl 16, mask 34
[     1.000000] cpu1: system tick frequency 12 MHz
[     1.000000] cpu1: 32K instruction (32 b/l), 64K data (32 b/l), 1024K =
external (64 b/l)
[     1.000000] memory-controller at mainbus0 not configured
[     1.000000] memory-controller at mainbus0 not configured
[     1.000000] schizo0 at mainbus0: addr 4000ff00000: Tomatillo, =
version 4, ign 7c0, bus B 0 to 0
[     1.000000] schizo0:  pci0 at schizo0
[     1.000000] pci0: i/o space, memory space enabled
[     1.000000] bge0 at pci0 dev 2 function 0: Broadcom BCM5704C Dual =
Gigabit Ethernet
[     1.000000] bge0: interrupting at ivec 37c8
[     1.000000] bge0: HW config 00000000, 00000000, 00000000, 00000000 =
00000000
[     1.000000] bge0: ASIC BCM5704 B0 (0x2100), Ethernet address =
00:14:4f:91:1c:8e
[     1.000000] brgphy0 at bge0 phy 1: BCM5704 1000BASE-T media =
interface, rev. 0
[     1.000000] brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, =
1000baseT, 1000baseT-FDX, auto
[     1.000000] bge1 at pci0 dev 2 function 1: Broadcom BCM5704C Dual =
Gigabit Ethernet
[     1.000000] bge1: interrupting at ivec 37c9
[     1.000000] bge1: HW config 00000000, 00000000, 00000000, 00000000 =
00000000
[     1.000000] bge1: ASIC BCM5704 B0 (0x2100), Ethernet address =
00:14:4f:91:1c:8f
[     1.000000] brgphy1 at bge1 phy 1: BCM5704 1000BASE-T media =
interface, rev. 0
[     1.000000] brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, =
1000baseT, 1000baseT-FDX, auto
[     1.000000] schizo1 at mainbus0: addr 4000f600000: Tomatillo, =
version 4, ign 780, bus A 0 to 0
[     1.000000] schizo1:  pci1 at schizo1
[     1.000000] pci1: i/o space, memory space enabled
[     1.000000] ebus0 at pci1 dev 7 function 0: Acer Labs M1533 PCI-ISA =
Bridge, revision 0x00
[     1.000000] flashprom at ebus0 addr 0-fffff, 290-290 not configured
[     1.000000] rtc0 at ebus0 addr 70-71: mc146818 compatible =
time-of-day clock: m5819p
[     1.000000] pcfiic0 at ebus0 addr 320-321 ipl 2e
[     1.000000] iic0 at pcfiic0: I2C bus
[     1.000000] i2c-bridge (SUNW,i2c-imax) at iic0 addr 0x0b not =
configured
[     1.000000] i2c-bridge (SUNW,i2c-imax) at iic0 addr 0x0c not =
configured
[     1.000000] seeprom0 at iic0 addr 0x51: motherboard-fru-prom: size =
8192
[     1.000000] seeprom1 at iic0 addr 0x54: chassis-fru-prom: size 8192
[     1.000000] seeprom2 at iic0 addr 0x58: power-supply-fru-prom: size =
8192
[     1.000000] seeprom3 at iic0 addr 0x52: power-supply-fru-prom: size =
8192
[     1.000000] spdmem0 at iic0 addr 0x5b
[     1.000000] spdmem0: DDR SDRAM (registered), data ECC, 512MB, 286MHz =
(PC-2300)
[     1.000000] spdmem0: 13 rows, 11 cols, 1 ranks, 4 banks/chip, 7.0ns =
cycle time
[     1.000000] spdmem0: tAA-tRCD-tRP-tRAS: 1-3-3-7
[     1.000000] spdmem0: voltage SSTL 2.5V, refresh time 7.8us =
(self-refreshing)
[     1.000000] spdmem1 at iic0 addr 0x5c
[     1.000000] spdmem1: DDR SDRAM (registered), data ECC, 512MB, 286MHz =
(PC-2300)
[     1.000000] spdmem1: 13 rows, 11 cols, 1 ranks, 4 banks/chip, 7.0ns =
cycle time
[     1.000000] spdmem1: tAA-tRCD-tRP-tRAS: 1-3-3-7
[     1.000000] spdmem1: voltage SSTL 2.5V, refresh time 7.8us =
(self-refreshing)
[     1.000000] spdmem2 at iic0 addr 0x5d
[     1.000000] spdmem2: DDR SDRAM (registered), data ECC, 512MB, 333MHz =
(PC-2700)
[     1.000000] spdmem2: 13 rows, 11 cols, 1 ranks, 4 banks/chip, 6.0ns =
cycle time
[     1.000000] spdmem2: tAA-tRCD-tRP-tRAS: 1-3-3-7
[     1.000000] spdmem2: voltage SSTL 2.5V, refresh time 7.8us =
(self-refreshing)
[     1.000000] spdmem3 at iic0 addr 0x5e
[     1.000000] spdmem3: DDR SDRAM (registered), data ECC, 512MB, 333MHz =
(PC-2700)
[     1.000000] spdmem3: 13 rows, 11 cols, 1 ranks, 4 banks/chip, 6.0ns =
cycle time
[     1.000000] spdmem3: tAA-tRCD-tRP-tRAS: 1-3-3-7
[     1.000000] spdmem3: voltage SSTL 2.5V, refresh time 7.8us =
(self-refreshing)
[     1.000000] spdmem4 at iic0 addr 0x63
[     1.000000] spdmem4: DDR SDRAM (registered), data ECC, 512MB, 286MHz =
(PC-2300)
[     1.000000] spdmem4: 13 rows, 11 cols, 1 ranks, 4 banks/chip, 7.0ns =
cycle time
[     1.000000] spdmem4: tAA-tRCD-tRP-tRAS: 1-3-3-7
[     1.000000] spdmem4: voltage SSTL 2.5V, refresh time 7.8us =
(self-refreshing)
[     1.000000] spdmem5 at iic0 addr 0x64
[     1.000000] spdmem5: DDR SDRAM (registered), data ECC, 512MB, 286MHz =
(PC-2300)
[     1.000000] spdmem5: 13 rows, 11 cols, 1 ranks, 4 banks/chip, 7.0ns =
cycle time
[     1.000000] spdmem5: tAA-tRCD-tRP-tRAS: 1-3-3-7
[     1.000000] spdmem5: voltage SSTL 2.5V, refresh time 7.8us =
(self-refreshing)
[     1.000000] spdmem6 at iic0 addr 0x65
[     1.000000] spdmem6: DDR SDRAM (registered), data ECC, 512MB, 286MHz =
(PC-2300)
[     1.000000] spdmem6: 13 rows, 11 cols, 1 ranks, 4 banks/chip, 7.0ns =
cycle time
[     1.000000] spdmem6: tAA-tRCD-tRP-tRAS: 1-3-3-7
[     1.000000] spdmem6: voltage SSTL 2.5V, refresh time 7.8us =
(self-refreshing)
[     1.000000] spdmem7 at iic0 addr 0x66
[     1.000000] spdmem7: DDR SDRAM (registered), data ECC, 512MB, 286MHz =
(PC-2300)
[     1.000000] spdmem7: 13 rows, 11 cols, 1 ranks, 4 banks/chip, 7.0ns =
cycle time
[     1.000000] spdmem7: tAA-tRCD-tRP-tRAS: 1-3-3-7
[     1.000000] spdmem7: voltage SSTL 2.5V, refresh time 7.8us =
(self-refreshing)
[     1.000000] rscrtc (i2c-ds1307) at iic0 addr 0x68 not configured
[     1.000000] seeprom4 at iic0 addr 0x28: nvram: size 8192
[     1.000000] pcagpio0 at iic0 addr 0x22: PCA9555
[     1.000000] pcagpio1 at iic0 addr 0x23: PCA9555
[     1.000000] pcagpio2 at iic0 addr 0x25: PCA9555
[     1.000000] pcagpio3 at iic0 addr 0x34: PCA9555
[     1.000000] pcagpio4 at iic0 addr 0x44: PCA9555
[     1.000000] pcagpio5 at iic0 addr 0x38: PCA9556
[     1.000000] adm1026hm0 at iic0 addr 0x2e: ADM1026 hardware monitor: =
rev. 0x4, step. 0x5
[     1.000000] adm1026hm0: 7 fans, 3 temperatures, 15 voltages
[     1.000000] lmtemp0 at iic0 addr 0x4e: temperature-sensor LM75 =
Temperature Sensor
[     1.000000] power at ebus0 addr 800-82f ipl 20 not configured
[     1.000000] com0 at ebus0 addr 3f8-3ff ipl 2c: ns16550a, 16-byte =
FIFO
[     1.000000] com0: console
[     1.000000] com1 at ebus0 addr 2e8-2ef ipl 2c: ns16550a, 16-byte =
FIFO
[     1.000000] rmc-comm at ebus0 addr 3e8-3ef ipl 2c not configured
[     1.000000] alipm0 at pci1 dev 6 function 0: 223KHz clock
[     1.000000] iic1 at alipm0: I2C bus
[     1.000000] ohci0 at pci1 dev 10 function 0: Acer Labs M5237 USB 1.1 =
Host Controller (rev. 0x03)
[     1.000000] ohci0: interrupting at ivec 7a7
[     1.000000] ohci0: OHCI version 1.0, legacy support
[     1.000000] usb0 at ohci0: USB revision 1.0
[     1.000000] aceride0 at pci1 dev 13 function 0: Acer Labs M5229 UDMA =
IDE Controller (rev. 0xc4)
[     1.000000] aceride0: bus-master DMA support present
[     1.000000] aceride0: using PIO transfers above 137GB as workaround =
for 48bit DMA access bug, expect reduced performance
[     1.000000] aceride0: primary channel configured to native-PCI mode
[     1.000000] aceride0: using ivec 2f98 for native-PCI interrupt
[     1.000000] atabus0 at aceride0 channel 0
[     1.000000] aceride0: secondary channel configured to native-PCI =
mode
[     1.000000] atabus1 at aceride0 channel 1
[     1.000000] schizo2 at mainbus0: addr 4000e600000: Tomatillo, =
version 4, ign 700, bus A 0 to 0
[     1.000000] schizo2:  pci2 at schizo2
[     1.000000] pci2: i/o space, memory space enabled
[     1.000000] esiop0 at pci2 dev 2 function 0: Symbios Logic =
53c1010-66 (ultra3-wide scsi)
[     1.000000] esiop0: using on-board RAM
[     1.000000] esiop0: interrupting at ivec 2f29
[     1.000000] scsibus0 at esiop0: 16 targets, 8 luns per target
[     1.000000] esiop1 at pci2 dev 2 function 1: Symbios Logic =
53c1010-66 (ultra3-wide scsi)
[     1.000000] esiop1: using on-board RAM
[     1.000000] esiop1: interrupting at ivec 2f28
[     1.000000] scsibus1 at esiop1: 16 targets, 8 luns per target
[     1.000000] schizo3 at mainbus0: addr 4000ef00000: Tomatillo, =
version 4, ign 740, bus B 0 to 0
[     1.000000] schizo3:  pci3 at schizo3
[     1.000000] pci3: i/o space, memory space enabled
[     1.000000] bge2 at pci3 dev 2 function 0: Broadcom BCM5704C Dual =
Gigabit Ethernet
[     1.000000] bge2: interrupting at ivec 375c
[     1.000000] bge2: HW config 00000000, 00000000, 00000000, 00000000 =
00000000
[     1.000000] bge2: ASIC BCM5704 B0 (0x2100), Ethernet address =
00:14:4f:91:1c:90
[     1.000000] brgphy2 at bge2 phy 1: BCM5704 1000BASE-T media =
interface, rev. 0
[     1.000000] brgphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, =
1000baseT, 1000baseT-FDX, auto
[     1.000000] bge3 at pci3 dev 2 function 1: Broadcom BCM5704C Dual =
Gigabit Ethernet
[     1.000000] bge3: interrupting at ivec 375d
[     1.000000] bge3: HW config 00000000, 00000000, 00000000, 00000000 =
00000000
[     1.000000] bge3: ASIC BCM5704 B0 (0x2100), Ethernet address =
00:14:4f:91:1c:91
[     1.000000] brgphy3 at bge3 phy 1: BCM5704 1000BASE-T media =
interface, rev. 0
[     1.000000] brgphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, =
1000baseT, 1000baseT-FDX, auto
[     1.000000] pcons at mainbus0 not configured
[     1.000000] WARNING: system needs entropy for security; see =
entropy(7)
[     1.000000] timecounter: Timecounter "tick-counter" frequency =
1503000000 Hz quality 100
[     1.000003] timecounter: Timecounter "stick-counter" frequency =
12000000 Hz quality 200
[     1.000016] No counter-timer -- using %stick at 12MHz as system =
clock.
[     1.000016] timecounter: Timecounter "clockinterrupt" frequency 100 =
Hz quality 0
[     2.370204] scsibus0: waiting 2 seconds for devices to settle...
[     2.445897] scsibus1: waiting 2 seconds for devices to settle...
[     2.517642] uhub0 at usb0: NetBSD (0x0000) OHCI root hub (0x0000), =
class 9/0, rev 1.00/1.00, addr 1
[     2.625780] uhub0: 2 ports with 2 removable, self powered
[     2.680200] atapibus0 at atabus0: 2 targets
[     2.840200] cd0 at atapibus0 drive 0: <DV-28E-N, , 1.6A> cdrom =
removable
[     2.920200] cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA =
mode 2 (Ultra/33)
[     2.920200] cd0(aceride0:0:0): using PIO mode 4
[     4.630202] sd0 at scsibus0 target 0 lun 0: <SEAGATE, =
ST373207LSUN72G, 045A> disk fixed
[     4.723533] sd0: 70007 MB, 14089 cyl, 24 head, 424 sec, 512 =
bytes/sect x 143374738 sectors
[     4.830202] sd0: 25426 trailing sectors not covered by disklabel
[     4.910201] sd0: sync (12.50ns offset 62), 16-bit (160.000MB/s) =
transfers, tagged queueing
[     5.020200] sd1 at scsibus0 target 1 lun 0: <SEAGATE, =
ST373207LSUN72G, 045A> disk fixed
[     5.120729] sd1: 70007 MB, 14089 cyl, 24 head, 424 sec, 512 =
bytes/sect x 143374738 sectors
[     5.230201] sd1: sync (12.50ns offset 62), 16-bit (160.000MB/s) =
transfers, tagged queueing
[     7.310200] entropy: best effort
[    13.580199] swwdog0: software watchdog initialized
[    13.660202] sd0: 25426 trailing sectors not covered by disklabel
[    13.732387] sd0: 25426 trailing sectors not covered by disklabel
[    13.810201] root on sd1a dumps on sd1b
[    13.890201] root file system type: ffs
[    13.936913] kern.module.path=3D/stand/sparc64/11.99.5/modules
[    15.480201] entropy: ready=